OUTWATER SDH-SW12-SS User manual

Brand
OUTWATER
Model
SDH-SW12-SS
Type
User manual

OUTWATER SDH-SW12-SS is a premium sliding single wood door hardware kit made from 304-grade stainless steel. It features adjustable mounting brackets for standard 16" U.S. stud spacing or variations. The kit includes a 78-3/4" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, door stops, and an adjustable installation wrench.

OUTWATER SDH-SW12-SS is a premium sliding single wood door hardware kit made from 304-grade stainless steel. It features adjustable mounting brackets for standard 16" U.S. stud spacing or variations. The kit includes a 78-3/4" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, door stops, and an adjustable installation wrench.

BARN
DOOR
HARDWARE
THE
LOFT
Hardware kit for sliding single wood door.
MODEL No. SDH-SW12-SS INSTALLATION MANUAL
TOOLS REQUIRED INCLUDED IN KIT
• Plumb Line
• Pencil
• Phillips Head Screwdriver
• 10mm Drill Bit
• 5.5mm Drill Bit
• Level
• Tape Measure
• Power Drill
A
B C D E
F G H
I
JK
A78-3/4" Rail x1
BDoor Roller Hardware x2
CEnd Bracket x2
DCenter Bracket x2
EST4.8x50 Bolt x4
FST5.5x32 Screw x3
GFloor Anchor x3
HRouted Floor Guide x1
IDoor Stops x2
JAdjustable Installation Wrench x1
K4mm/8mm Allen Keys x1
Architectural Products by Outwater assumes no liability for improper installation.
304 Grade Stainless Steel
THE LOFT
Wall Blocking
1. To obtain maximum weight capacity, all fasteners
must be mounted into solid wood studs or wall
blocking or mounted to a header board.
2. Adjustable mounting brackets allow for standard
16" U.S. stud spacing, or any variation.
Suggested wall bracket spacing.
Brackets must be secured into wall blocking.
Attach rail to wall as shown.
NOTES
Architectural Products by Outwater assumes no liability for improper installation.
Find the centerline of the track. Using a level, mark
a horizontal line twice the door width long. Mark the
bracket screw locations into the wall blocking.
Attach the wall portion of the brackets as shown.
Consult a structural engineer if you have questions
about what type of wall blocking is required.
Architectural Products by Outwater assumes no liability for improper installation.
1. Remove the anti-rise pin and drill holes centered in door thickness. The door should be routed at this time.
2. Mount the rolling straps to the door and position the door on the rail.
Adjust the stops accordingly. Tighten the set screw with
sufcient force to drive the set screw into the bar after
making the nal adjustment.
Plumb the door and mark the positions of the oor
guides. Mount the oor guides to the oor.
THE LOFT
Adjust the door stops accordingly. Tighten the set screw
with sufcient force to drive the set screw into the bar
after making the nal adjustment.
Reattach the anti-rise pin to the door rollers
THE LOFT
Architectural Products by Outwater assumes no liability for improper installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

OUTWATER SDH-SW12-SS User manual

Brand
OUTWATER
Model
SDH-SW12-SS
Type
User manual

OUTWATER SDH-SW12-SS is a premium sliding single wood door hardware kit made from 304-grade stainless steel. It features adjustable mounting brackets for standard 16" U.S. stud spacing or variations. The kit includes a 78-3/4" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, door stops, and an adjustable installation wrench.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents