FURNITURE FSDH-STPKT-5-DD Installation guide

FSDH-STPKT-5-DD
Brand
FURNITURE
Model
FSDH-STPKT-5-DD
Type
Installation guide

FURNITURE FSDH-STPKT-5-DD is a sliding door hardware kit suitable for ¾" and 1" doors. It includes all the necessary components for a quick and easy installation, such as door rollers, anti-jump disks, door stops, end caps, mounting brackets, anchors, screws, and a 1.5mm Allen key. The rail can be trimmed up to 2½" on both sides to accommodate different door widths. Routed door guides are also included to ensure smooth and quiet operation.

FURNITURE FSDH-STPKT-5-DD is a sliding door hardware kit suitable for ¾" and 1" doors. It includes all the necessary components for a quick and easy installation, such as door rollers, anti-jump disks, door stops, end caps, mounting brackets, anchors, screws, and a 1.5mm Allen key. The rail can be trimmed up to 2½" on both sides to accommodate different door widths. Routed door guides are also included to ensure smooth and quiet operation.

Architectural Products by Outwater assumes no liability for improper installation.
MODEL No. FSDH-STPKT-*-5-DD INSTALLATION MANUAL
TOOLS REQUIRED INCLUDED IN KIT
• Plumb Line
• Pencil
• Phillips Head Screwdriver
• 4mm Drill Bit
• Wrench
• Level
• Power Drill
• Tape Measure
FURNITURE
FURNITURE
E F
G H
K
L
I
J
ADoor Roller Hardware x4
BAnti-Jump Disk x4
CDoor Stop Hardware x2
DEnd Cap x2
EMounting Bracket for ¾" and 1" Doors x4 ea.
FM6x60 Bolt + Washer x8
GRouted Door Guide x2
HST4.2x35 Screw x4
IAnchor x4
J1.5mm Allen Key x1
KHole Cover x4
L60" Rail x1
AB C D
PLEASE NOTE: The installation manual is a suggested guideline. Adjustments may need to be made based on your specic application.
Architectural Products by Outwater assumes no liability for improper installation.
3 ½” 3 ½”
6” 16”16”16”
60”
6”
Using a pencil, mark the locations where you will drill holes
as indicated.
Using a power drill with a 4mm drill bit, drill holes as indicated.
Before beginning installation, attach the door stops [C]
to the rail [L].
1
2
UNDERSTANDING YOUR RAIL
INSTALLATION
Architectural Products by Outwater assumes no liability for improper installation.
Install the rail, and mounting brackets [E].
3
Mounting Bracket [E]
4
Drill holes into the doors as indicated. Attach the roller straps [A].
5"
Mounting Screws
It is suggested that the roller straps [A] be mounted 5" from the edge of the
doors to the neck of the roller straps.
NOTE: Trimming the rail will alter the position of the roller hardware.
Adjust accordingly.
Architectural Products by Outwater assumes no liability for improper installation.
3⅛"
3⅛"
FOR ¾" DOORS
FOR 1" DOORS
Allow a minimum 3-1/8" clearance above the doors.
Architectural Products by Outwater assumes no liability for improper installation.
5
Attach the anti-jump disks [B] to the doors.
Attach the doors to the rail [L] and lock the anti-jump disks [B] into position. Doors should be routed beforehand
if using the routed door guides [G].
5
6
Roller Strap [A]
Anti-Jump Disk [B]
Anti-Jump Disk [B]
(x2)
(x2)
Architectural Products by Outwater assumes no liability for improper installation.
6
Use the hole covers [K] to give the rail a
nished look.
Once cut, add the end caps [D] to the ends of the rail and secure with a
set screw.
NOTE: If you are trimming the rail, do so equally. Each
rail can be trimmed equally up to 2½" on both sides.
However; trimming will alter the position of the roller
hardware. Adjust accordingly.
7
8
Routed Door Guide [G]
Hole Covers [K]
The rail can be trimmed if necessary using a band saw
or hacksaw. Use blades suitable for iron or stainless
steel depending on your rail.
9
End Cap [D]
End Cap [D]
2½" Max
2½" Max
If using the routed door guides [G], install them at this time.
Repeat steps 4-7 for additional door.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

FURNITURE FSDH-STPKT-5-DD Installation guide

FSDH-STPKT-5-DD
Brand
FURNITURE
Model
FSDH-STPKT-5-DD
Type
Installation guide

FURNITURE FSDH-STPKT-5-DD is a sliding door hardware kit suitable for ¾" and 1" doors. It includes all the necessary components for a quick and easy installation, such as door rollers, anti-jump disks, door stops, end caps, mounting brackets, anchors, screws, and a 1.5mm Allen key. The rail can be trimmed up to 2½" on both sides to accommodate different door widths. Routed door guides are also included to ensure smooth and quiet operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents