DALI RGBW Touch Controller 09.230PR6.04062
DALI Master/
DALI Master software
via computer
Function introduction
Important: Read All Instructions Prior to Installation
19.4 mm
60.3 mm
DALI Wall
Panel Controller
Front side
Back side
52.0 mm
60.3 mm
52.0 mm
Wiring diagram
12-24VDC
PSU AC 100-240V
Output Signal DALI signal
Power Supply 12-24VDC
Power consumption 200 mA
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 86x86x29.1mm
• Touch sensitive.
• Glass interface (white & black).
• Comply to DALI standard protocol IEC 62386-102, IEC
62386-207 and in compliance with DALI products from
other international incorporation.
• 4 light zones are available for switch, dimming and RGB
color control, each zone can control 4 DALI addresses.
• Enable to set start DALI address number (0-63) for the 4
zones by rotary switches on the back.
• Enable to save 1 scene for each light zone
• Built-in 8 Color Sequences
Product Data
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
Safety & Warnings
RGB color panel
ON/OFF button
012
3
4
5
6
7
89
012
3
4
5
6
7
89
(x10 )
(x1)
D1 D2V+V-
DC Power input
DALI signal output DALI Wall
Panel Contr oller
012
3
4
5
6
7
89
012
3
4
5
6
7
89
(x10)
(x1)
D1 D2V+V-
123
4
GND
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V/36V
CV PSU
Connect wi th R GBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
Connect wi th R GBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
123
4
GND
4 light zones, click to select,
press and hold down to turn
ON/OFF
R, G, B, W channel, click to turn
ON/OFF, press and hold down to
increase/decrease light intensity
1*(0~9) for setting
units position
10*(0~9) for setting
tens position
Rotary switches for setting start DALI address number (0-63),
the number equals to tens position plus units position
Waterproof grade Ip20
Scene button, press and
hold down to save a scene,
click to recall
Play/Pause button, click to
play/pause running effects,
press and hold down to
speed up/down
Brightness button, press and
hold down to
increase/decrease light
intensity
Installation
12-24VDC
Power Supply
Operation
1.Set start DALI address number for the light zones by rotary switches on the back:
Set the number as X (0-63):
Zone number Z1 will control DALI addresses X, X+1, X+2 and X+3,
Zone number Z2 will control DALI addresses X+4, X+5, X+6 and X+7,
Zone number Z3 will control DALI addresses X+8, X+9, X+10 and X+11,
Zone number Z4 will control DALI addresses X+12, X+13, X+14 and X+15,
Note: if X is set as 63, zone 1 will control DALI address 63, 00, 01 and 02, zone 2 will control address 03, 04, 05
and 06, zone 3 will control address 07, 08, 09 and 10, zone 4 will control address 11, 12, 13 and 14.
2. Save color/scene/mode:
1) Turn on the DALI master controller and click Z1, Z2, Z3 or Z4 that is paired with DALI slaves.
2) Touch the color panel to choose a color/scene, then press and hold down the button S for 3 seconds until the
LED indicator on the panel flashes twice, which means the color/scene is saved successfully.
3. Recall the saved colors/scenes
Turn on the DALI master controller and click any of Z1, Z2, Z3 or Z4 to select a zone that you would like to
recall, then click button S to recall the saved.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sunricher SR-2300TS-RGB-DT6 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Legrand DMX Dali Gateway Installation guide
-
-
SKYDANCE DA-P User manual
-
WAGO 753-647 User manual
-
ABB i-bus KNX User manual
-
-
-
-
PXM PX787 User manual
-