Zippity Outdoor Products ZP19018 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19018
Type
Operating instructions

Zippity Outdoor Products ZP19018:

With its 42”H x 92”W design, this fence is suitable for semi-permanent applications and can be trimmed horizontally to fit specific spaces using a fine-toothed circular saw or hacksaw. Assembly requires a cordless drill, level, hammer, and basic tools. The fence comes with 24 self-auguring stainless steel screws for secure installation into the ground. It features a scallop pattern created by pickets of varying heights, which slide into predrilled holes in the top and bottom rails. Joiner clips fasten the top and bottom rails together.

Zippity Outdoor Products ZP19018:

With its 42”H x 92”W design, this fence is suitable for semi-permanent applications and can be trimmed horizontally to fit specific spaces using a fine-toothed circular saw or hacksaw. Assembly requires a cordless drill, level, hammer, and basic tools. The fence comes with 24 self-auguring stainless steel screws for secure installation into the ground. It features a scallop pattern created by pickets of varying heights, which slide into predrilled holes in the top and bottom rails. Joiner clips fasten the top and bottom rails together.

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at
1 877 234 6196
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps
(4)
2. Top Rail
(
2) - 1½” x 1½“ x 92”
3.
Posts
(4) - 7/8“ x 1½” x 61½”
4. Pickets
(40) - 1 - ¼” x 1½” x 37 7/8“
2 - ¼” x 1½” x 36 1/4“
3 - ¼” x 1½” x 35 1/8“
4 - ¼” x 1½” x 34 1/4“
5 - ¼” x 1½” x 33 7/8“
5. Bottom
Rail (
2) - 1½“ x 1½” x 92“
6.
Joiner Clips
(4)
7.
3/4” Self-Auguring Stainless Steel Screw
(24)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Manchester Vinyl Picket Fence Kit
2-Pack (42”H x 92”W)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 2.0/060317
1
3
2
4
5
Ground
This fence can easily be trimmed down horizontally
to fit your custom space. Use a fine toothed circular
saw or hack saw.
7
Not to Scale
6
2 5/8 in
62 in
23 in23 in
92 in
10 1/2 in
26 1/2 in
36 in
2 in
42 in
20 in
46 in
44 1/2 in
THIS FENCE IS DESIGNED
FOR SEMI-PERMANENT
APPLICATIONS
2
Position the top & bottom rails as illustrated and slide the two
posts down thru the large routed holes in the top and bottom
rails until the predrilled holes in both rails are aligned with the
pre-drilled holes in both posts.
Note the difference between the top and bottom rails.
Tip!
Shine an LED light from smart phone or flashlight down the
end of the posts to help identify alignment of pre-drilled
holes if necessary.
Secure the rails to the post with screws on both sides of the
rails as illustrated.
1
2
STEP ONE
Manchester Vinyl Picket Fence Instructions
1
Note: Align Holes
2
Note: Orientate the bottom of Posts as Illustrated
Note: Underside of Bottom Rail is blank
compared to the Top Rail with
holes for pickets on both sides.
STEP TWO
Pickets are identified 1, 2, 3, 4 and 5 to create scallop pattern. Please
insert in pattern as identified in illustration. Starting with the
tallest picket, slide each one down thru the top rail and into the
bottom rail.
Note: The tabs on the bottom of the pickets are intended to go
into the bottom rail to lock picket into place.
1
3
Manchester Vinyl Picket Fence Instructions
1
Note: Once inserted, the
pickets will lock into place.
To remove the picket(s),
gently insert a butter knife
along the picket direction
as shown and slowly pull up
the picket(s).
x
x
x
x
STEP THREE
4
1
Install fence into Ground
Move the fence to its final location and identify the location
of posts.
Loosen the top 10” to 12” of the ground using a claw hammer
and screw driver (or something equivalent) as illustrated.
Add water to loosen soil.
Use a block of wood to the protect the top of post and
gently hammer each post into the ground equally.
2
2
x
x
1
3
4
Manchester Vinyl Picket Fence Instructions
Block of Wood
3
4
1
If your ground is too hard, or you have more than 3 or 4 panels
to install, please consider:
Purchase a 1 3/4” diameter auger bit (commonly used for
planting tulips) as illustrated ($15-$20 on Amazon.com)
Drill a hole in the ground at the desired location only about
12” to 16” deep.
Fill the holes with water as illustrated.
Push fence posts into the holes as illustrated.
2
3
4
1
5
STEP THREE
OPTIONS IN HARD GROUND
Manchester Vinyl Picket Fence Instructions
3
2
4
3
6
STEP THREE
3
Install fence into Ground - Continued
Level the assembled unit and backfill and compact dirt around
the base of each post to strengthen the unit.
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
4
4
Level
4
Manchester Vinyl Picket Fence Instructions
1
2
Top Rail
Bottom
Rail
Top Rail
Bottom
Rail
1
2
45° Application
7
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685
www.zippity-outdoor.com
STEP FOUR
1
2
Fasten Joiner Clips
Fasten joiner clips by screwing into place on the top of the top
rail and top of the bottom rail as illustrated.
Screws are self-drilling.
Fasten the opposite end of the joiner clip as illustrated.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Zippity Outdoor Products ZP19018 Operating instructions

Brand
Zippity Outdoor Products
Model
ZP19018
Type
Operating instructions

Zippity Outdoor Products ZP19018:

With its 42”H x 92”W design, this fence is suitable for semi-permanent applications and can be trimmed horizontally to fit specific spaces using a fine-toothed circular saw or hacksaw. Assembly requires a cordless drill, level, hammer, and basic tools. The fence comes with 24 self-auguring stainless steel screws for secure installation into the ground. It features a scallop pattern created by pickets of varying heights, which slide into predrilled holes in the top and bottom rails. Joiner clips fasten the top and bottom rails together.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents