Whirlpool AKR 948 AL Program Chart

Brand: Whirlpool

Model: AKR 948 AL

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

AKR 948 IX WP

Whirlpool AKR 948 AL is a versatile kitchen appliance designed to optimize your cooking experience. Its powerful extraction system with three-speed settings efficiently removes steam, fumes, and odors from your kitchen, leaving the air fresh and clean. The halogen bulbs provide bright illumination, enhancing visibility while cooking. Additionally, the grease filter captures grease particles, preventing them from accumulating on surfaces and ensuring a cleaner kitchen environment.



5019 318 33071

AKR 948

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 50 cm (Elektroherdplatten), 75 cm (Gas-,

Öl- oder Kohleherdplatten). Befolgen Sie bei der Installation die Nummerierung

.....). Schließen Sie das Gerät erst nach erfolgter Installation an die

Stromversorgung an. Achtung! Das Auslassrohr und die Befestigungsmanschetten

(15) sind nicht im Lieferumfang inbegriffen und müssen gesondert erworben

werden.

INSTALLATION SHEET

Minimum height above cooker: 50 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To install, follow points (1

.....). Do not connect the

appliance to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps (15) are not supplied and must be bought

separately.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 50 cm (cuisinière électrique),

75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....). Ne branchez pas l'appareil tant que l'installation

n'est pas terminée. Attention ! Le conduit d'évacuation et les colliers de fixation

(15) ne sont pas fournis et doivent être acheter à part.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 50 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering

.....). Geef het apparaat geen stroom totdat de installatie geheel

voltooid is. Let op! De afvoerbuis en de klembanden (15) worden niet

bijgeleverd en moeten apart worden aangeschaft.

31833071.fm Page 1 Tuesday, January 7, 2003 2:08 PM



5019 318 33071

AKR 948

FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 50 cm (quemadores eléctricos), 75 cm

(quemadores de gas, gasóleo o carbón). Para el montaje, siga la numeración

...). No conecte el aparato a la corriente eléctrica hasta que la

instalación esté completamente finalizada. ¡Atención! El tubo de descarga y las

abrazaderas (15) no están incluidas y se compran aparte.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 50 cm (fogões eléctricos), 75 cm (fogões a gás,

gasóleo ou carbono). Para a montagem siga a numeração (1

.....). Não

ligue o aparelho à corrente eléctrica até a instalação estar concluída. Atenção! O

tubo de descarga e as tiras de fixação (15) não são fornecidas e devem ser

compradas à parte.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 50 cm (fuochi elettrici), 75 cm (fuochi a gas,

gasolio o carbone). Per il montaggio seguire la numerazione (1

.....).

Non dare corrente allapparecchio finché linstallazione non è totalmente

completata. Attenzione! Il tubo di scarico e le fascette di fissaggio (15) non

sono fornite e vanno acquistate a parte.

ùüùü+ùùùþ

ü$12.)12.1.)2"0120" FP02!"0120" FP0120"

.0! #02!0. #0! # +.22  21.  #1202

.!1





2! 3 / 2020002!)!0*.21#10#!

2  !&12"0.212.1"! 1 $1&."..&".2.

 !.120!&1"/0/.202..!0.. 2 *$&!12

31833071.fm Page 2 Tuesday, January 7, 2003 2:08 PM



5019 318 33071

AKR 948

31833071.fm Page 3 Tuesday, January 7, 2003 2:08 PM



5019 318 33071

AKR 948

Preliminary information for installing the hood:

Disconnect the power supply at the domestic main switch before carrying out electrical connections.

1. Place the extraction unit on a flat surface and fit the bottom part of the hood on it

(remove the grease filter/s).

2. Carry out the electrical connections between the two parts.

3. Fix the hood to the extraction unit with 10 screws.

4. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations.

5. Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the

centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the

hood: remember that with installation completed the bottom of the hood must be at least 50 cm above

the cooktop in the case of electric cookers and 75 cm in the case of gas or mixed cookers.

6. Place the support bracket on the hole diagram so that it matches the dotted rectangle, mark the two

external holes and drill, then remove the hole diagram, insert 2 wall plugs and fix the hood support

bracket with two 5x45 mm screws.

7. Hook the hood to the bracket.

8. Adjust the distance between the hood and the wall.

9. Adjust the hood horizontally.

10. From inside the hood, mark the holes for fixing the hood permanently.

11. Remove the hood from the bracket.

12. Drill on the marks (Ø 8 mm - see step 10).

13. Insert 2 wall plugs.

14. Fit the flue support bracket G to the wall and against the ceiling, use the support bracket as hole diagram

(the small slot on the support must match the line drawn on the wall - step 4) and mark 2 holes with the

pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs.

15. Fix the flue support bracket to the wall with two 5x45 mm screws.

16. Hook the hood to the bottom bracket.

17. Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY).

18. Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar

B located above the extraction motor unit.

For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter

operation, fix the deflector F to the flue support bracket G with 2 screws and connect the other end of

the exhaust pipe to the deflector collar F (if the collar is not already fitted it should be inserted on the

deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter

(not provided, to be ordered separately) they are conveyed back to the kitchen through the grid H.

19. Carry out the electrical connection.

20. Apply the flues and fix them with 2 screws (20a) to the flue support G (20b).

21. Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction

unit.

Refit the grease filter/s and check for correct hood operation.

INSTALLATION - ASSEMBLY INSTRUCTIONS

D F NL E

P I GR

31833071.fm Page 7 Tuesday, January 7, 2003 2:08 PM



5019 318 33071

AKR 948

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters - Fig. 1: pull the spring

release handle (f) downwards, then remove the

filter.

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface

is covered.

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f - Fig. 1).

3. Turn the side knobs 90° and then remove the

filter holder (g - Fig. 2).

4. Fit the carbon filter (h - Fig. 2) in the filter

holder (i - Fig. 2).

5. Refit the filter holder and secure it to the hood

with the screw (g - Fig. 2).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible,

using a normal dishwasher detergent. To avoid

particles of food or dirt settling on the filter during

washing and giving rise to unpleasant smells, it is

advisable to wash the filter on its own. After

washing, dry the filter in the oven at 100° C for

10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off (m-Fig. 3) the lamp cover (p-Fig. 3).

3. Remove the burnt-out bulb.

Replace using 20 W max halogen bulbs only,

making sure not to touch them with your hands.

4. Close the lighting unit (snap-close).

CONTROL PANEL

A. Light ON/OFF switch.

B. ON/OFF and speed 1 selector switch

(small amount of steam and fumes).

B+C. Speed 2 selector switch

(medium amount of steam and fumes).

B+D. Speed 3 selector switch

(large amount of steam and fumes).

Fig. 1

Fig. 4

Fig. 2

Fig. 3

PRODUCT SHEET

D F NL E

P I GR

31833071.fm Page 8 Tuesday, January 7, 2003 2:08 PM

Whirlpool AKR 948 AL Program Chart

Brand: Whirlpool

Model: AKR 948 AL

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

AKR 948 IX WP

Download PDF

report

Whirlpool AKR 948 AL Program Chart

This manual is also suitable for

Whirlpool AKR 948 AL Program Chart

Related papers

Other documents