PPI OmniX Single Set Point Temperature Controller User manual

Brand
PPI
Model
OmniX Single Set Point Temperature Controller
Type
User manual
Operation Manual
This brief manual is primarily meant for quick reference to wiring connections
and parameter searching. For more details on operation and application;
please log on to www.ppiindia.net
Setpoint Locking
Parameters Settings
(Default Value)
SETPOINT LOCKING : PAGE - 0
No
Yes
(Default : No)
Resolution
Option Range (Min. to Max.)
0 to +960°C
-200 to +1375°C
J Type T/C
RTD Pt100
K Type T/C
TABLE- 1
RTD Pt100
-199.9 to +600.0°C
1°C
1°C
0.1°C
-199 to +600°C
1°C
1.0 to 2.0
(Default : 1.2)
Overshoot Inhibit
Factor
Overshoot Inhibit
Enable / Disable
Self-Tune
Command Yes
No
(Default : No)
Disable
Enable
(Default : Disable )
Parameters Settings
(Default Value)
SUPERVISORY PARAMETERS : PAGE - 13
Keys Operation
Symbol Key Function
Press to enter or exit set-up mode.
DOWN
UP
ENTER
Press to store the set parameter value
and to scroll to the next parameter on
the PAGE.
Press to increase the parameter
value. Pressing once increases the
value by one count; keeping pressed
speeds up the change.
Press to decrease the parameter
value. Pressing once decreases the
value by one count; keeping pressed
speeds up the change.
PAGE
FRONT PANEL LAYOUT
ELECTRICAL CONNECTIONS
FRONT PANEL
Temperature Error Indications
Message
Over-range
(Temperature above Max. Range)
Under-range
(Temperature below Min. Range)
Open
(Thermocouple / RTD broken)
Temperature Error Type
Parameters Settings
(Default Value)
Setpoint High
Offset for
Measured Temp.
Setpoint Low
Digital Filter
Input Type
Control Logic
INPUT / OUTPUT CONFIGURATION PARAMETERS : PAGE - 12
(Default : Type K)
Reverse
Direct
(Default : Reverse)
Min. Range to Setpoint
High for the selected Input type
(Default : Min. Range for
the selected Input Type)
-1999 to 9999 or
-199.9 to 999.9
(Default : 0)
0.5 to 25.0 Seconds
(in steps of 0.5 Seconds)
(Default : 1.0)
(Default : Max. Range for
the selected Input Type)
Setpoint Low to Max.
Range for the selected
Input type
Control Output
Type
(Default)
Relay
SSR
Parameters Settings
(Default Value)
Integral Time
Proportional Band
0.1 to 999.9
(Default : 10.0)
0 to 1000 Seconds
(Default : 100 sec)
0 to 250 Seconds
(Default : 25 sec)
Derivative Time
Cycle Time
PID CONTROL PARAMETERS : PAGE - 10
0.5 to 120.0 Seconds
(in steps of 0.5 secs.)
(Default : 20.0 sec)
(Default)
On-Off
PID
HYSTERESIS
CONTROL MODE
1 to 999 or 0.1 to 99.9
(Default : 2 or 0.2)
Economic Self-Tune PID
Temperature Controller
Omni
PPI
OP
Upper Readout
Lower Readout
ENTER Key
UP KeyDOWN Key
PAGE Key
Output status
Indicator
Omni
Refer Table 4.2 for various
available 'Input Types'
along with their respective
Ranges and Resolutions.
C NCNO
85~265
VAC
CONTROL
OUTPUT
INPUT
SSR
T/C
Pt100
N
L
RELAY
CONTROL
OUTPUT
5
1
2
3
4
6
7
8
9
10
Omni
85 ~ 265 V
AC SUPPLY
RELAY
1
2
3
4
5
6
7
8
9
10
11
12
NCCNO
+
-
SSR
T/C
Pt100
+
-
INPUT
N
L
CONTROL
OUTPUT
CONTROL
OUTPUT
Omni 72
T/C
Pt100
INPUT
RELAY NO NCC
13
14
15
16
17
12
18
11
9
10
8
6
7
1
3
2
4
5
85 ~ 265 V
AC SUPPLY
L N
+
-
SSR
CONTROL
OUTPUT
CONTROL
OUTPUT
Omni 96
Compressor
Time Delay
(Default : 0)
0 to 600 Sec.
(in steps of 0.5 Sec.)
101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar - 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
E: [email protected][email protected],
Jan 2022
  • Page 1 1

PPI OmniX Single Set Point Temperature Controller User manual

Brand
PPI
Model
OmniX Single Set Point Temperature Controller
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents