Parameters
Operation Manual
This brief manual is primarily meant for quick reference to wiring connections
and parameter searching. For more details on operation and application;
please log on to www.ppiindia.net
Parameters
INPUT CONFIGURATION PARAMETERS : PAGE - 12
ALARM PARAMETERS (OUTPUT-2) : PAGE - 11
Settings
Settings
Input Type Controller Version:
0 - 20mA
4 - 20mA
0 - 5 V
0 - 10 V
1
0.1
0.01
0.001
Resolution
-1999 to 9999
(with selected Resolution)
DC Range Low
DC Range High
Offset For PV
Alarm-1 Type
Alarm-1 Hysteresis 1 to 999
(with selected Resolution)
Alarm-1 Logic Normal
Reverse
Alarm-1 Inhibit No
Yes
Alarm-2 Type
Parameters Settings
Alarm-2 Inhibit
Parameters Settings
-1999 to 9999
(with selected Resolution)
Alarm-1 Setpoint
-1999 to 9999
(with selected Resolution)
Alarm-2 Setpoint
OPERATOR PARAMETERS : PAGE - 0
Parameters Settings
View Only
Maximum Process
Value
View Only
Minimum Process
Value
Reset PV Monitor
PV MIN / MAX PARAMETERS : PAGE - 1
-1999 to 9999
(with selected Resolution)
-1999 to 9999
(with selected Resolution)
No
Yes
No
Yes
None
Process Low
Process High
None
Process Low
Process High
PV Error Indications
Message
Over-range (PV above
Max. Range)
Under-range (PV below
Min. Range)
PV Error Type
ELECTRICAL CONNECTIONS
Keys Operation
Keep pressed for approximately 5
seconds to enter / exit Set-up mode.
Symbol Key Function
DOWN
UP
Press to increase the parameter
value. Pressing once increases the
value by one count; holding pressed
speeds up the change.
Press to decrease the parameter
value. Pressing once decreases the
value by one count; holding pressed
speeds up the change.
PRG
PROGRAM
MODE
1 to 999
(with selected Resolution)
Alarm-2 Hysteresis
Alarm-2 Logic Normal
Reverse
Front Panel
FRONT PANEL LAYOUT
PROGRAM
Key
UP Key
DOWN Key
Process Value
Display
PRG
Alarm-1
Indicator
Alarm-2
Indicator
Proce
48H
PRG
PROGRAM
Key
DOWN Key
UP Key
Process Value
Display Alarm-2
Indicator
Alarm-1
Indicator
Proce
NOTE:- FOR RELAY OUTPUT ONLY
LCR is to be connected to contactor coil for
suppressing noises. (Refer LCR connection
Diagram given below)
CONTACTOR
1 3 5 13
A1 L1 L2 L3 NO
2 4 6 14
A2 T1 T2 T3
CONTACTOR
COIL L
N
LCR
LCR CONNECTION TO CONTACTOR COIL
Process Indicator with Alarms
Proce
1 2 345678
910 11 12 13 14 15 16
C
NO
NC
C NCNO
RELAY
SSR
L N
2 & 3 short for mA
2 & 3 open for V
{
V
OUTPUT-2
OUTPUT-1
85 ~ 265 V
AC SUPPLY
DC INPUT
RELAY
SSR
48 x 96
mA
48 x 48
C
L N
NCNO
1
2
3
4
5
6
7
8
9
10
C
NO
2 & 3 short for mA
2 & 3 open for V
{
SSR
RELAY
OUTPUT-1
OUTPUT-2
85 ~ 265 V
AC SUPPLY
RELAY
SSR
DC INPUT
V
mA
2 & 3 short for mA
2 & 3 open for V
{
SSR
RELAY
V
OUTPUT-1
OUTPUT-2
85 ~ 265 V
AC SUPPLY
RELAY
SSR
DC INPUT
96 x 96
NO
NC C
NO NCC
13
14
15
16
17
12
18
11
9
10
8
6
7
1
3
2
4
5
mA
L N
1
2
3
4
5
6
7
8
9
10
11
12
V
mA
2 & 3 short for mA
2 & 3 open for V
{
RELAY
OUTPUT-2
85 ~ 265 V
AC SUPPLY
RELAY
SSR
DC INPUT OUTPUT-1
SSR
72 x 72
NC C NO
NCC
NO L N
101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar - 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
Jan 2022
