2. Hagerco
  3. 6000 Series - Grade 2 Medium Duty - Overhead Door Holder and Stop
6000 Series - Grade 2 Medium Duty - Overhead Door Holder and Stop

Hagerco 6000 Series - Grade 2 Medium Duty - Overhead Door Holder and Stop Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Hagerco 6000 Series - Grade 2 Medium Duty - Overhead Door Holder and Stop Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of a Hagerco 6000 Series Overhead Door Holder and Stop?
    Where can I find the installation instructions for the Hagerco 6000 Series Door Holder and Stop?
    What are the different types of Hagerco 6000 Series Door Holders and Stops available?
    What is the maximum weight capacity of the Hagerco 6000 Series Door Holder and Stop?
    What is the difference between a Hold Open and a Friction Hold Open?
Main Body
Jamb Arm
Slider Arm
Jamb Bracket
Stop Spring
C
B
1"
24.6
A
MORTISE BRACKET
INTO FRAME
2-7/8"
72.9
25/32"
19.8
3/8"
9.5
1/2"
12.7
1/2"
12.7
1/2"
12.7
7/16"
11.5
5/16"
8.3
5/8"
16.1
3/8"
9.2
C
L
DOOR REINFORCEMENT
FRAME REINFORCEMENT
3/16"
4.9
1. PARTS
Screw Chart
Hinge Side
Pre Installation Notes:
1. Hollow metal frames must be properly reinforced with 3/16"(5mm) thick plates that are at least 12"(305mm) long.
2. Hollow metal doors must be properly reinforced with 3/16"(5mm) as shown on page 1.
3. Hold open(6017) and Friction(6015) are not permitted for use on fire doors.
4. Stop only(6016) is subject to job specification for fire door use.
1) Determine frame opening and desired degree of door opening. With this information use the
chart below to locate, mark and drill the "A" and "C" channel mounting hole locations. Install the channel body
with spring end toward hinges.
2) Locate and mark desired dimension "B" Cut out the "Jamb Bracket Template" from the bottom of the page
and align on frame to locate and drill the four jamb bracket mounting holes. Install the jamb bracket.
3) Both "A" and "B" Dimensions are to be measuered form the door edge, and the Jamb face respectively.
2. INSTALL OVERHEAD DOOR HOLDER/STOP (ODHS) (Right Hand Shown)
B
All dimensions shown in [] are in
millimeters
6000 SERIES- MEDIUM DUTY
CONCEALED DOOR STOPS & HOLDERS
INSTALLATION INSTRUCTIONS
REV: 10
DRAWING NO: I-CL00451
SHEET 1 OF 3
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
Hold Open engagement
switch
OFF
position
Hold Open engagement
switch
ON
position
Jamb Arm
Slider Arm
Stop Spring
Adjustment Arm
Set Screws
Jamb Arm
Stop Spring
Slider Bar
Slider Arm
Hold Open Engagement Switch
Hold Open Adjustment Screw
Friction Adjustment Screws
Open the door then align and insert the
jamb arm into the slider arm.
If it applies, disengage the hold open
engagement switch (step 5a). With the door
held at the desired maximum opening angle,
position the slider bar against the stop spring.
Tighten the three adjustment arm set screws.
Tighten to a minimum of 20 in-lbs (WARNING:
over tightening may result in damage to the
main arm).
If dead stop is required, position the door 5-7
degrees less then the desired dead stop. Then
tighten as instructed above.
5a. OPTIONAL HOLD OPEN (6017)
5b. OPTIONAL FRICTION HOLD OPEN (6015)
Using a Hex Key, turn the friction adjustment
screws clockwise to increase the friction and
counter-clockwise to lower the friction.
Pressure should be evenly distributed across
both screws
Using a Philips
screwdriver, turn the
hold open adjustment
screw clockwise to
increase the hold-
open tension and
counter-clockwise to
lower the tension.
3. ARM ALIGNMENT
4. SETTING DESIRED DOOR OPENING
REV: 10
DRAWING NO: I-CL00451
SHEET 2 OF 3
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
6000 SERIES- MEDIUM DUTY
CONCEALED DOOR STOPS & HOLDERS
INSTALLATION INSTRUCTIONS
Y
X
1/2"
12.7
1-1/4"
31.8
1-1/16"
27
3-5/8"
92.46
Z
W
Arm Cut-Out
Body Cut-Out
Hinge Edge
Front View
1/4" Hold open selector hole
optional for use on
6017 ONLY
A
A
Hinge Edge
Single Acting Application
Double Acting Application
Top View
Arm Cut-Out
B
B
Hinge Edge
Top View
Cross Section B-B
Cross Section A-A
7/8"
22.2
C
L
C
L
7/8"
22.2
DOOR PREP FOR ALL STYLES OF HOLD OPENS AND STOPS
REV: 10
DRAWING NO: I-CL00451
SHEET 3 OF 3
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - (800) 325-9995 - Fax (800) 782-0149
6000 SERIES- MEDIUM DUTY
CONCEALED DOOR STOPS & HOLDERS
INSTALLATION INSTRUCTIONS
/