Hager 3221 Installation guide

Hager
Brand
Hager
Model
3221
Category
Garage Door Opener
Type
Installation guide
THUMB TURN
ASSEMBLY
LATCH MOUNTING PLATE
LATCH
DEADBOLT
STRIKE
WOOD FRAME
REINFORCER
DUST BOX
MOUNTING SCREWS
F OR USE ON DOORS 1-3/8" to 1-3/4"
(35mm-45mm) THICK
TOOLS REQUIRED FOR NEW INSTALLATION:
(1) Phillips Head Screwdriver
(1) 2-1/8" (54mm) Hole Saw
(1) 1" (25.4mm) Drill Bit
(1) Chisel
TOOLS REQUIRED FOR REPLACEMENT INSTALLATION:
(1) Phillips Head Screwdriver
FOR REMODELING OR NEW CONSTRUCTION:
- Follow all steps
3221 Thumbturn Only Deadbolt
Installation Instructions
FOLD HERE
ON DOOR EDGE
1-3/8"
3545
1-3/4"
T E MP L ATE
1-9/16"
40
CAUTION
：
DO NOT DRILL 2-1/8" (54mm) HOLE
THROUGH TO OPPOSITE SIDE OF DOOR
.
(READ INSTRUCTIONS CAREFULLY)
2-1/8" (5 mm) HOLE4
Make 1"(25.4mm) hole at center
of door edge.
2-3/8" ( 60mm ) BACKSET
2-3/4" ( 70mm ) BACKSET
1. MARK DOOR
2. DRILL HOLES
3. PREP DOOR
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
2-1/8" (54mm) HOLE
1-3/16" (31mm) DEEP
1"(25.4mm) HOLE
4-1/8"(105mm)
DEEP
DOOR FACE
DOOR EDGE
Measure center line of lock; height as desired from finished floor.
Select 2-3/4" or optional 2-3/8" backset, fold and apply template
to interior side of door and mark center of door as indicated on
template. Mark center hole on door face through guide on template.
(See Step 7 for changing latch backset)
Drill 1" (25.4 mm) hole
4-1/8" (105 mm) deep
in center of door edge.
Drill 2-1/8" (54mm) hole
1-3/16" (31 mm) deep
on interior door face.
CAUTION:
Do not drill completely through the door face.
Insert latch in hole, keeping latch face parallel to
face of door edge.
Mark outline and remove latch.
Chisel 5/32" (4 mm) deep or
until latch face is flush with door edge.
Refer to Step 5 & 6 when installing latch.
a. b.
c.
TEMPLATE
7/28/08
HAGER COMPANIES139 Victor Street, St. Louis, MO 63104 (800) 325-9995 FAX (800) 782-0149
4. INSTALL STRIKE
5. INSTALL LATCH MOUNTING PLATE
a. b.
c.
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH MOUNTING PLATE
SIDE VIEW ASSEMBLED
RELEASE
SWITCH
2-3/8"
BACKSET
2-3/4"
BACKSET
LATCH
CRANK
THUMBTU
RN
ASSEMBLY
TORQUE BLADE
LATCH
PLATE
LATCH MOUNTING PLATE
To set latch to 2-3/8" setting, pull up Release Switch on both sides.
While holding Release Switch up, slide crosshairs to the 2-3/8" marked hole.
Adjust
the latch to the proper
backset, see below for details
on adjusting the latch.
Insert
the latch mounting plate
into the holes on the latch.
Close
door. Locate strike in jamb
and center line of strike. Open
door and extend line to door stop.
Measure half of door thickness
plus 1/8" from door stop. Vertically
mark centerline for strike.
Drill (2) 1"(25.4 mm) holes 1-1/4" (31.7 mm)
deep in door jamb, 5/16" (8 mm) above and
5/16’" (8 mm) below horizontal center line.
CAUTION
:
Hole must be drilled a full 1-1/4" (31.7 mm)
deep to ensure proper functioning.
Match screw holes on strike with
vertical centerlines on jamb. Mark
outline of strike and chisel 1/4"
(6.4mm) deep for flush fit of dust
box, wood frame reinforcer, and
strike. Place dust box and wood
frame reinforcer into mortised area
and tighten to the frame using 3"
wood screws. Insert the strike and
tighten to the frame with #8 screws.
Insert latch into 1" diameter hole and tighten to the door edge using #8 screws.
Insert torque blade horizontally into latch crank until thumb turn assembly is
flush with door face. Tighten assembly using screws.
7. BACKSET ADJUSTMENT
6. INSTALL LATCH THUMBTURN ASSEMBLY
Note: When installing on a metal door, the latch mounting plate may be pulled
up against the inside door face as the mounting screws are tightened. This is
normal when installing on a metal door.
  • Page 1 1
  • Page 2 2

Hager 3221 Installation guide

Hager
Brand
Hager
Model
3221
Category
Garage Door Opener
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents