2. Haworth
  3. 6100-0066

Haworth 6100-0066 Operating instructions

  • Hello! I've reviewed the installation instructions for the PLANES HEIGHT ADJUSTABLE BENCH and INTUITY gallery panel brackets. This document provides detailed steps for assembling the various bracket options, including tie plate installation and specific tool usage. I'm ready to answer any questions you have about the installation process.
  • What tools are required for the installation?
    Where are the tie plates installed?
    What is the purpose of the angle driver?
5_52595 1 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
Gallery Panel Bracket (Options)
Installation Instructions
PLANES HEIGHT ADJUSTABLE BENCH/INTUITY
CUSTOMER SERVICE PHONE: 1-800-426-8562
Scale 1 : 1
0 11/2
1/4 1/4
A
Gallery Panel
B
S116
S116
S-1
S-1
D
S117
Gallery Panel
Bracket
B1
Gallery Panel
Bracket
Gallery Panel
Bracket
C
Angle
Bracket
Tools Required
#2
PLANES HEIGHT ADJUSTABLE BENCH BRACKET
INTUITY BRACKET
9/64”
3/16”
1/8” Drill
90° Angle Drill
Attachment
1
2
A
5_52595 2 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
GALLERY PANEL ASSEMBLY
TIE PLATE
G
#8 x 3/4" Flat Head Screw
(S-17)
12”
1/4”
1/8”
Drill
A2
S-17
NOTE: Tie plates (A2) are installed on
the user side NOT customer side.
1
(S116)
1/4-20 x 3/8" Set Screw
1/4-20 x 1/2" Socket Head Bolt
(117)
SNUG ONLY
A
Gallery Panel
B
B
S116
S116
S-1
S116
S117
Gallery Panel
Bracket
B1
B1
Gallery Panel
Bracket
C
Angle
Bracket
5_52595 3 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
PLANES - GALLERY PANEL
#10 x 1" Pan Head Screw
(S-1)
1/4”
1/8”
Drill
5_52595 4 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
(S116)
1/4-20 x 3/8" Set Screw
1/4-20 x 1/2" Socket Head Bolt
(117)
2
3A
A
SNUG ONLY
B
B1
C
C
S117
S116
B
B1
S-1
G
90° Angle Drill
Attachment
#10 x 1" Pan Head Screw
(S-1)
#2
NOTE: Angle driver is used
to install screws (S-1).
(S116)
1/4-20 x 3/8" Set Screw
5_52595 5 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
PLANES - GALLERY PANEL
3B
A
TIGHTEN
S116
TIGHTEN
C
S116
4
B
B1
S-1
G
1/4”
1/8”
Drill
#8 x 3/4" Flat Head Screw
(S-17)
A2
S-17
NOTE: Tie plates (A2) are installed on
the user side NOT customer side.
12”
#10 x 1" Pan Head Screw
(S-1)
90° Angle Drill
Attachment
#2
NOTE: Angle driver is used
to install screws (S-1).
A
Gallery Panel
G
INTUITY DESKING - GALLERY PANEL
S-1
S-1
D
D
Gallery Panel
Bracket
5_52595 6 of 6 6100-0066 4Rev:Part No:Page:E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
#10 x 1" Pan Head Screw
(S-1)
NOTE: Install gallery panel bracket (D)
to worksurface rst and make sure it’s
ush with edge. Then attached to
gallery panel (A).
/