ABB Relion REL670 2.1 IEC User manual

Relion

®

670 series

Line differential protection RED670 2.1 IEC

Product guide

Contents

1. Application..................................................................... 3

2. Available functions..........................................................9

3. Differential protection....................................................21

4. Impedance protection.................................................. 24

5. Current protection........................................................ 29

6. Voltage protection........................................................ 31

7. Frequency protection....................................................32

8. Multipurpose protection................................................32

9. Secondary system supervision..................................... 33

10. Control........................................................................ 33

11. Scheme communication..............................................35

12. Logic...........................................................................37

13. Monitoring...................................................................39

14. Metering......................................................................41

15. Human machine interface............................................42

16. Basic IED functions..................................................... 42

17. Station communication ...............................................42

18. Remote communication.............................................. 43

19. Hardware description.................................................. 43

20. Connection diagrams.................................................. 46

21. Technical data.............................................................47

22. Ordering for customized IED......................................116

23. Ordering for pre-configured IED.................................126

24. Ordering for Accessories........................................... 132

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any errors

that may appear in this document. Drawings and diagrams are not binding.

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks

of their respective holders.

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

2 ABB

1. Application

The IED is used for the protection, control and monitoring of

overhead lines and cables in all types of networks. The IED can

be used from distribution up to the highest voltage levels. It is

suitable for the protection of heavily loaded lines and multi-

terminal lines where the requirement for tripping is one-, two-,

and/or three-phase. The IED is also suitable for protection of

cable feeders to generator block transformers.

The phase segregated current differential protection provides

an excellent sensitivity for high resistive faults and gives a

secure phase selection. The availability of six stabilized current

inputs per phase allows use on multi-breaker arrangements in

three terminal applications or up to five terminal applications

with single breaker arrangements. The communication

between the IEDs involved in the differential scheme is based

on the IEEE C37.94 standard and can be duplicated for

important installations when required for redundancy reasons.

Charging current compensation allows high sensitivity also on

long overhead lines and cables.

A full scheme distance protection is included to provide

independent protection in parallel with the differential scheme in

case of a communication channel failure for the differential

scheme. The distance protection then provide protection for

the entire line including the remote end back up capability either

in case of a communications failure or via use of an independent

communication channel to provide a fully redundant scheme of

protection (that is a second main protection scheme). Eight

channels for intertrip and other binary signals are available in

the communication between the IEDs.

A high impedance differential protection can be used to protect

T-feeders or line reactors.

The auto-reclose for single-, two- and/or three phase reclosing

includes priority circuits for multi-breaker arrangements. It co-

operates with the synchronism check function with high-speed

or delayed reclosing.

High set instantaneous phase and earth overcurrent, four step

directional or un-directional delayed phase and earth

overcurrent, thermal overload and two step under- and

overvoltage functions are examples of the available functions

allowing the user to fulfill any application requirement.

The IED can also be provided with a full control and interlocking

functionality including co-operation with the synchronism

check function to allow integration of the main or back-up

control.

Disturbance recording and fault locator are available to allow

independent post-fault analysis after primary disturbances. The

Disturbance recorder will also show remote station currents, as

received to this IED, time compensated with measure

communication time.

Out of Step function is available to separate power system

sections close to electrical centre at occurring out of step.

The IED can be used in applications with IEC 61850-9-2LE

process bus with up to six merging units (MU) depending on

other functionality included in the IED.

Each MU has eight analogue channels, normally four currents

and four voltages. Conventional and Merging Unit channels can

be mixed freely in the application.

If IEC 61850-9-2LE communication is

interrupt, data from the merging units (MU)

after the time for interruption will be

incorrect. Both data stored in the IED and

displayed on the local HMI will be corrupt.

For this reason it is important to connect

signal from respective MU units

(SMPLLOST) to the disturbance recorder.

Forcing of binary inputs and outputs is a convenient way to test

wiring in substations as well as testing configuration logic in the

IEDs. Basically it means that all binary inputs and outputs on the

IED I/O modules (BOM, BIM, IOM & SOM) can be forced to

arbitrary values.

Central Account Management is an authentication

infrastructure that offers a secure solution for enforcing access

control to IEDs and other systems within a substation. This

incorporates management of user accounts, roles and

certificates and the distribution of such, a procedure completely

transparent to the user.

The Flexible Product Naming allows the customer to use an

IED-vendor independent 61850 model of the IED. This

customer model will be exposed in all IEC 61850

communication, but all other aspects of the IED will remain

unchanged (e.g., names on the local HMI and names in the

tools).

The logic is prepared with a graphical tool. The advanced logic

capability allows special applications such as automatic

opening of disconnectors in multi-breaker arrangements,

closing of breaker rings, load transfer logics etc. The graphical

configuration tool ensures simple and fast testing and

commissioning.

A loop testing function allows complete testing including

remote end IED when local IED is set in test mode.

Forcing of binary inputs and outputs is a convenient way to test

wiring in substations as well as testing configuration logic in the

IEDs. Basically it means that all binary inputs and outputs on the

IED I/O modules (BOM, BIM, IOM & SOM) can be forced to

arbitrary values.

Central Account Management is an authentication

infrastructure that offers a secure solution for enforcing access

control to IEDs and other systems within a substation. This

incorporates management of user accounts, roles and

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1 Issued: December 2015

Revision: -

ABB 3

certificates and the distribution of such, a procedure completely

transparent to the user.

The Flexible Product Naming allows the customer to use an

IED-vendor independent 61850 model of the IED. This

customer model will be exposed in all IEC 61850

communication, but all other aspects of the IED will remain

unchanged (e.g., names on the local HMI and names in the

tools). This offers significant flexibility to adapt the IED to the

customers system and standard solution

Communication via optical connections ensures immunity

against disturbances.

Four packages have been defined for following applications:

• Single-breaker (double or single bus) with three phase

tripping (A31)

• Single-breaker (double or single bus) with single phase

tripping (A32)

• Multi-breaker (one-and a half or ring) with three phase

tripping (B31)

• Multi-breaker (one-and a half or ring) with single phase

tripping (B32)

Optional functions are not configured but a maximum

configuration with all optional functions are available as

template in the graphical configuration tool. Analog inputs and

binary input/output signals are pre-defined for basic use. Other

signals may be required by each particular application.

Add binary I/O boards as required for the application when

ordering.

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

4 ABB

Description of configuration A31

QB1

QB2

QA1

QB9

QC9

WA1

WA2

RED670 A31 – Single Breaker with Three phase tripping

12AI (6I+6U)

LOV PTUV

27 3U<

CV MMXN

MET P/Q

ETP MMTR

MET W/Varh

V MMXU

MET U

LC PTTR

26 θ>

C MMXU

MET I

UV2 PTUV

27 2(3U<)

C MSQI

MET Isqi

BRC PTOC

46 Iub>

DRP RDRE

DFR/SER DR

OV2 PTOV

59 2(3U>)

VN MMXU

MET UN

V MSQI

MET Usqi

OC4 PTOC

51_67 4(3I>)

CC RBRF

50BF 3I>BF

PH PIOC

50 3I>>

LMB RFLO

21FL FL

L3C PDIF

87L 3Id/I>

REM CT

WA2_VT

Other Functions available from the function library

VD SPVC

60 Ud>

FDPS PDIS

21

NS4 PTOC

46I2 4(I2>)

CV GAPC

2(I>/U<)

ZCV PSOF

Optional Functions

VDC PTOV

60 Ud>

Q CBAY

Control

ROV2 PTOV

59N 2(U0>)

CCS SPVC

87 INd/I

FMPS PDIS

21

EF PIOC

50N IN>>

GOP PDOP

32 P>

HZ PDIF

87 Id>

L6C PDIF

87L 3Id/I>

STB PTOC

50STB3I>STB

S SIMG

63

LT3C PDIF

87LT 3Id/I>

LT6C PDIS

87LT 3Id/I>

SA PTOF

81 f>

SA PTUF

81 f<

GUP PDUP

37 P<

ZMM PDIS

21 Z<

ZMH PDIS

21 Z<

ZMQ PDIS

21 Z<

ZM RPSB

68 Zpsb

PSP PPAM

78 Ucos

ZSM GAPC

OEX PVPH

24 U/f>

ZC PSCH

85

ZCRW PSCH

85

ZCLC PSCH S CILO

3 Control

VN MMXU

MET UN

VN MMXU

MET UN

SMB RREC

79

5(0→1)

SMP PTRC

94 1→0

25 SC/VC

SES RSYN

FUF SPVC

U>/I<

LDL PSCH

87L

WA1_VT

LINE_CT

S SIML

71

CC PDSC

52PD PD

SDEPSDE

67N IN>

EF4 PTOC

51N_67N

4(IN>)

ZMF PDIS

21 Z<

ZD RDIR

21 Z<_>

PSL PSCH

Zpsl

OOS PPAM

78 Ucos

SA PFRC

81 df/dt<>

ECRW PSCH

85

EC PSCH

85

S CSWI

3 Control

S XSWI

3 Control

Q CRSV

3 Control

S XCBR

3 Control

S SCBR

LINE_VT

IEC05000842 V4 EN

Figure 1. Configuration diagram for configuration A31

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 5

Description of configuration A32

QB1

QB2

QA1

QB9

QC9

WA1

WA2

RED670 A32 – Single Breaker with Single phase tripping

12AI (6I+6U)

LOV PTUV

27 3U<

CV MMXN

MET P/Q

ETP MMTR

MET W/Varh

V MMXU

MET U

LC PTTR

26 θ>

C MMXU

MET I

UV2 PTUV

27 2(3U<)

C MSQI

MET Isqi

BRC PTOC

46 Iub>

DRP RDRE

DFR/SER DR

OV2 PTOV

59 2(3U>)

VN MMXU

MET UN

V MSQI

MET Usqi

OC4 PTOC

51_67 4(3I>)

CC RBRF

50BF 3I>BF

PH PIOC

50 3I>>

LMB RFLO

21FL FL

L3C PDIF

87L 3Id/I>

REM CT

WA2_VT

Other Functions available from the function library

VD SPVC

60 Ud>

FDPS PDIS

21

NS4 PTOC

46I2 4(I2>)

CV GAPC

2(I>/U<)

ZCV PSOF

Optional Functions

VDC PTOV

60 Ud>

Q CBAY

Control

ROV2 PTOV

59N 2(U0>)

CCS SPVC

87 INd/I

FMPS PDIS

21

EF PIOC

50N IN>>

GOP PDOP

32 P>

HZ PDIF

87 Id>

L6C PDIF

87L 3Id/I>

STB PTOC

50STB3I>STB

S SIMG

63

LT3C PDIF

87LT 3Id/I>

LT6C PDIS

87LT 3Id/I>

SA PTOF

81 f>

SA PTUF

81 f<

GUP PDUP

37 P<

ZMM PDIS

21 Z<

ZMH PDIS

21 Z<

ZMQ PDIS

21 Z<

ZM RPSB

68 Zpsb

PSP PPAM

78 Ucos

ZSM GAPC

OEX PVPH

24 U/f>

ZC PSCH

85

ZCRW PSCH

85

ZCLC PSCH S CILO

3 Control

VN MMXU

MET UN

VN MMXU

MET UN

SMB RREC

79

5(0→1)

SMP PTRC

94 1→0

25 SC/VC

SES RSYN

FUF SPVC

U>/I<

LDL PSCH

87L

WA1_VT

LINE_CT

S SIML

71

CC PDSC

52PD PD

SDEPSDE

67N IN>

EF4 PTOC

51N_67N

4(IN>)

ZMF PDIS

21 Z<

ZD RDIR

21 Z<_>

PSL PSCH

Zpsl

OOS PPAM

78 Ucos

SA PFRC

81 df/dt<>

ECRW PSCH

85

EC PSCH

85

S CSWI

3 Control

S XSWI

3 Control

Q CRSV

3 Control

S XCBR

3 Control

S SCBR

LINE_VT

ZC1P PSCH

85

ZC1W PSCH

85

IEC05000840 V4 EN

Figure 2. Configuration diagram for configuration A32

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

6 ABB

Description of configuration B31

QB1

WA1_QB6

QB61

QB62

LINE2_QB9

WA2_QB6

WA1_QA1

TIE_QA1

RED670 B31: interruptor múltiple con disparo trifásico

12AI (6I+6U)

CC RBRF

50BF 3I>BF

VN MMXU

MET UN

LDL PSCH

87L

ETP MMTR

MET W/Varh

CV MMXN

MET P/Q

QB2

WA2_QA1

UV2 PTUV

27 3U<

OC4 PTOC

51_67 4(3I>)

OV2 PTOV

59 3U>

LOV PTUV

27 3U<

V MMXU

MET U

C MSQI

MET Isqi

DRP RDRE

DFR/SER DR

V MSQI

MET Usqi

SMB RREC

79 0→1

SMP PTRC

94 1→0

SES RSYN

25 SC

SMB RREC

79

5(0→1)

SMP PTRC

94 1→0

SES RSYN

25 SC/VC

FUF SPVC

U>/I<

LC PTTR

26 3I>STBθ>

C MMXU

MET I

BRC PTOC

46 Iub>

PH PIOC

50 3I>>

Σ

L6C PDIF

87L 3Id/I>

REM CT1

REM CT2

CC RBRF

50BF 3I>BF

LINE1_QB9

S SIMG

63

Otras funciones disponibles desde la biblioteca de funciones

Funciones opcionales

ROV2 PTOV

59N 2(U0>)

VDC PTOV

60 Ud>

STB PTOC

50STB3I>STB

CCS SPVC

87 INd/I

Q CBAY

3 Control

FDPS PDIS

21

FMPS PDIS

21

EF4 PTOC

51N_67N

4(IN>)

CV GAPC

2(I>/U<)

VD SPVC

60 Ud>

ZD RDIR

21 Z<_>

SDE PSDE

67N IN>

ZMH PDIS

21 Z<

HZ PDIF

87 Id>

NS4 PTOC

46I2 4(I2>)

ZSM GAPC

ZCV PSOF

OOS PPAM

78 Ucos

PSL PSCH

Zpsl

GUP PDUP

37 P<

LT6C PDIF

87LT 3Id/I>

EF PIOC

50N IN>>

ZMQ PDIS

21 Z<

ZM RPSB

68 Zpsb

ZMF PDIS

21 Z<

PSP PPAM

78 Ucos

ZMM PDIS

21 Z<

SA PFRC

81 df/dt<>

EC PSCH

85

SA PTUF

81 f<

SA PTOF

81 f>

OEX PVPH

24 U/f>

GOP PDOP

32 P>

S CILO

3 Control

S CSWI

3 Control

ZCLC PSCHZCRW PSCH

85

S SCBRQ CRSV

3 Control

ZC PSCH

85

ECRW PSCH

85

S XCBR

3 Control

S XSWI

3 Control

S SIML

71

CC PDSC

52PD PD

VN MMXU

MET UN

VN MMXU

MET UN

VN MMXU

MET UN

LMB RFLO

21FL FL

WA1

WA1_VT

WA1_CT

LINE1_VT

TIE_CT

LINE2_VT

WA2_VT

WA2

IEC05000843 V4 EN

Figure 3. Configuration diagram for configuration B31

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 7

Description of configuration B32

QB1

WA1_QB6

QB61

QB62

LINE2_QB9

WA2_QB6

WA1_QA1

TIE_QA1

RED670 B32 – Multi Breaker with Single phase tripping

12AI (6I+6U)

CC RBRF

50BF 3I>BF

VN MMXU

MET UN

LDL PSCH

87L

ETP MMTR

MET W/Varh

CV MMXN

MET P/Q

QB2

WA2_QA1

UV2 PTUV

27 3U<

OC4 PTOC

51_67 4(3I>)

OV2 PTOV

59 3U>

LOV PTUV

27 3U<

V MMXU

MET U

C MSQI

MET Isqi

DRP RDRE

DFR/SER DR

V MSQI

MET Usqi

SMB RREC

79 0→1

SMP PTRC

94 1→0

SES RSYN

25 SC

SMB RREC

79

5(0→1)

SMP PTRC

94 1→0

SES RSYN

25 SC/VC

FUF SPVC

U>/I<

LC PTTR

26 3I>STBθ>

C MMXU

MET I

BRC PTOC

46 Iub>

PH PIOC

50 3I>>

Σ

L6C PDIF

87L 3Id/I>

REM CT1

REM CT2

CC RBRF

50BF 3I>BF

LINE1_QB9

S SIMG

63

Other Functions available from the function library

Optional Functions

ROV2 PTOV

59N 2(U0>)

VDC PTOV

60 Ud>

STB PTOC

50STB3I>STB

CCS SPVC

87 INd/I

Q CBAY

3 Control

FDPS PDIS

21

FMPS PDIS

21

EF4 PTOC

51N_67N

4(IN>)

CV GAPC

2(I>/U<)

VD SPVC

60 Ud>

ZD RDIR

21 Z<_>

SDE PSDE

67N IN>

ZMH PDIS

21 Z<

HZ PDIF

87 Id>

NS4 PTOC

46I2 4(I2>)

ZSM GAPC

ZCV PSOF

OOS PPAM

78 Ucos

PSL PSCH

Zpsl

GUP PDUP

37 P<

LT6C PDIF

87LT 3Id/I>

EF PIOC

50N IN>>

ZMQ PDIS

21 Z<

ZM RPSB

68 Zpsb

ZMF PDIS

21 Z<

PSP PPAM

78 Ucos

ZMM PDIS

21 Z<

SA PFRC

81 df/dt<>

EC PSCH

85

SA PTUF

81 f<

SA PTOF

81 f>

OEX PVPH

24 U/f>

GOP PDOP

32 P>

S CILO

3 Control

S CSWI

3 Control

ZCLC PSCHZCRW PSCH

85

S SCBRQ CRSV

3 Control

ZC PSCH

85

ECRW PSCH

85

S XCBR

3 Control

S XSWI

3 Control

S SIML

71

VN MMXU

MET UN

VN MMXU

MET UN

VN MMXU

MET UN

LMB RFLO

21FL FL

WA1

WA1_VT

WA1_CT

LINE1_VT

TIE_CT

LINE2_VT

WA2_VT

WA2

CC PDSC

52PD PD

CC PDSC

52PD PD

ZC1W PSCH

85

ZC1P PSCH

85

IEC05000841 V4 EN

Figure 4. Configuration diagram for configuration B32

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

8 ABB

2. Available functions

Main protection functions

Table 1. Example of quantities

2 = number of basic instances

0-3 = option quantities

3-A03 = optional function included in packages A03 (refer to ordering details)

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 9

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

Differential protection

HZPDIF 87 1Ph high impedance differential protection 0-3 3-A02 3-A02 3-A02 3-A02

REFPDIF 87N Restricted earth fault protection, low impedance 0–2

L3CPDIF 87L Line differential protection, 3 CT sets, 2–3 line ends 1 1 1

L6CPDIF 87L Line differential protection, 6 CT sets, 3–5 line ends 1 1-A04 1 1-A04 1

LT3CPDIF 87LT Line differential protection, 3 CT sets, with inzone

transformers, 2–3 line ends

1 1-A05 1-A05

LT6CPDIF 87LT Line differential protection, 6 CT sets, with inzone

transformers, 3–5 line ends

1 1-A06 1-A06 1-A06 1-A06

LDLPSCH 87L Line differential protection logic 1 1 1 1 1

LDRGFC 11REL Additional security logic for differential protection 0-1

Impedance protection

ZMQPDIS,

ZMQAPDIS

21 Distance protection zone, quadrilateral characteristic 0-5 1-B10

3-B11

1-B10

3-B11

1-B10

3-B11

1-B10

3-B11

ZDRDIR 21D Directional impedance quadrilateral 0-2 1-B11 1-B11 1-B11 1-B11

ZMCPDIS,

ZMCAPDIS

21 Distance measuring zone, quadrilateral characteristic

for series compensated lines

0-5 3-B16 3-B16 3-B16 3-B16

ZDSRDIR 21D Directional impedance quadrilateral, including series

compensation

0-2 1-B16 1-B16 1-B16 1-B16

FDPSPDIS 21 Phase selection, quadrilateral characteristic with fixed

angle

0-2 1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

ZMHPDIS 21 Fullscheme distance protection, mho characteristic 0-5 4-B17 4-B17 4-B17 4-B17

ZMMPDIS,

ZMMAPDIS

21 Fullscheme distance protection, quadrilateral for

earth faults

0-5 4-B17 4-B17 4-B17 4-B17

ZDMRDIR 21D Directional impedance element for mho characteristic 0-2 1-B17 1-B17 1-B17 1-B17

ZDARDIR Additional distance protection directional function for

earth faults

0-2 1-B17 1-B17 1-B17 1-B17

ZSMGAPC Mho impedance supervision logic 0-1 1-B17 1-B17 1-B17 1-B17

FMPSPDIS 21 Faulty phase identification with load enchroachment 0-2 2-B17 2-B17 2-B17 2-B17

ZMRPDIS,

ZMRAPDIS

21 Distance protection zone, quadrilateral characteristic,

separate settings

0-5

FRPSPDIS 21 Phase selection, quadrilateral characteristic with fixed

angle

0-2

ZMFPDIS 21 High speed distance protection 0–1

ZMFCPDIS 21 High speed distance protection for series

compensated lines

0–1 1-B19 1-B19 1-B19 1-B19

ZMRPSB 68 Power swing detection 0-1 1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

PSLPSCH Power swing logic 0-1 1-B03 1-B03 1-B03 1-B03

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

10 ABB

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

PSPPPAM 78 Pole slip/out-of-step protection 0-1 1-B22 1-B22 1-B22 1-B22

OOSPPAM 78 Out-of-step protection 0–1 1-B22 1-B22 1-B22 1-B22

ZCVPSOF Automatic switch onto fault logic, voltage and current

based

0-1 1-B11

1-B16

1-B17

1-B11

1-B16

1-B17

1-B11

1-B16

1-B17

1-B11

1-B16

1-B17

PPLPHIZ Phase preference logic 0-1 1-B04

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 11

Back-up protection functions

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

Current protection

PHPIOC 50 Instantaneous phase overcurrent

protection

0-3 1 1 1 1

OC4PTOC

51_67

1)

Four step phase overcurrent protection 0-3 1 1 1 1

EFPIOC 50N Instantaneous residual overcurrent

protection

0-1 1-C24 1-C24 1-C24 1-C24

EF4PTOC 51N

67N

2)

Four step residual overcurrent protection 0-3 1-C24 1-C24 1-C24 1-C24

NS4PTOC 46I2 Four step directional negative phase

sequence overcurrent protection

0-2 1-C24 1-C24 1-C24 1-C24

SDEPSDE 67N Sensitive directional residual overcurrent

and power protection

0-1 1-C16 1-C16 1-C16 1-C16

LCPTTR 26 Thermal overload protection, one time

constant, Celsius

0–2 1 1 1 1

LFPTTR 26 Thermal overload protection, one time

constant, Fahrenheit

0–2 1 1 1 1

CCRBRF 50BF Breaker failure protection 0-2 1 2 1 2

STBPTOC 50STB Stub protection 0-2 1-B11 1B

1-B11

1-B11 1B

1-B11

CCPDSC 52PD Pole discordance protection 0-2 1 2 1 2

GUPPDUP 37 Directional underpower protection 0-2 1-C17 1-C17 1-C17 1-C17

GOPPDOP 32 Directional overpower protection 0-2 1-C17 1-C17 1-C17 1-C17

BRCPTOC 46 Broken conductor check 1 1 1 1 1

VRPVOC 51V Voltage restrained overcurrent protection 0-3

Voltage protection

UV2PTUV 27 Two step undervoltage protection 0-2 1 1 1 1

OV2PTOV 59 Two step overvoltage protection 0-2 1 1 1 1

OEXPVPH 24 Overexcitation protection 0-1 1-D03 1-D03 1-D03 1-D03

VDCPTOV 60 Voltage differential protection 0-2 2 2 2 2

LOVPTUV 27 Loss of voltage check 1 1 1 1 1

PAPGAPC 27 Radial feeder protection 0–1

Frequency protection

SAPTUF 81 Underfrequency protection 0-6 2-E02 2-E02 2-E02 2-E02

SAPTOF 81 Overfrequency protection 0-6 2-E02 2-E02 2-E02 2-E02

SAPFRC 81 Rate-of-change frequency protection 0-2 2-E02 2-E02 2-E02 2-E02

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

12 ABB

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

Multipurpose protection

CVGAPC General current and voltage protection 0-4 4-F01 4-F01 4-F01 4-F01

General calculation

SMAIHPAC Multipurpose filter 0-6

1) 67 requires voltage

2) 67N requires voltage

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 13

Control and monitoring functions

IEC 61850 ANSI Function description Line Differential

RED670

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

Control

SESRSYN 25 Synchrocheck, energizing check and synchronizing 0-2 1 2 1 2

SMBRREC 79 Autorecloser 0-4 1

1-H04

2

2-H05

1

1-H04

2

2-H05

APC10 3 Apparatus control for single bay, max 10 apparatuses

(1CB) incl. interlocking

0-1 1-H27 1-H27

APC15 3 Apparatus control for single bay, max 15 apparatuses

(2CBs) incl. interlocking

0-1 1-H08 1-H08

QCBAY Apparatus control 1 1 1 1 1

LOCREM Handling of LRswitch positions 1 1 1 1 1

LOCREMCTRL LHMI control of PSTO 1 1 1 1 1

SLGAPC Logic rotating switch for function selection and LHMI

presentation

15 15 15 15 15

VSGAPC Selector mini switch 20 20 20 20 20

DPGAPC Generic communication function for Double Point

indication

16 16 16 16 16

SPC8GAPC Single point generic control 8 signals 5 5 5 5 5

AUTOBITS AutomationBits, command function for DNP3.0 3 3 3 3 3

SINGLECMD Single command, 16 signals 4 4 4 4 4

I103CMD Function commands for IEC 60870-5-103 1 1 1 1 1

I103GENCMD Function commands generic for IEC 60870-5-103 50 50 50 50 50

I103POSCMD IED commands with position and select for IEC

60870-5-103

50 50 50 50 50

I103POSCMDV IED direct commands with position for IEC 60870-5-103 10 10 10 10 10

I103IEDCMD IED commands for IEC 60870-5-103 1 1 1 1 1

I103USRCMD Function commands user defined for IEC 60870-5-103 1 1 1 1 1

Secondary system

supervision

CCSSPVC 87 Current circuit supervision 0-2 1 2 1 2

FUFSPVC Fuse failure supervision 0-3 3 3 3 3

VDSPVC 60 Fuse failure supervision based on voltage difference 0-3 1-G03 1-G03 1-G03 1-G03

Logic

SMPPTRC 94 Tripping logic 6 6 6 6 6

TMAGAPC Trip matrix logic 12 12 12 12 12

ALMCALH Logic for group alarm 5 5 5 5 5

WRNCALH Logic for group warning 5 5 5 5 5

INDCALH Logic for group indication 5 5 5 5 5

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

14 ABB

IEC 61850 ANSI Function description Line Differential

RED670

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

AND, GATE, INV,

LLD, OR,

PULSETIMER,

RSMEMORY,

SRMEMORY,

TIMERSET, XOR

Basic configurable logic blocks (see Table 2) 40-280 40-28

0

40-280 40-28

0

40-28

0

ANDQT,

INDCOMBSPQT,

INDEXTSPQT,

INVALIDQT,

INVERTERQT,

ORQT,

PULSETIMERQT,

RSMEMORYQT,

SRMEMORYQT,

TIMERSETQT,

XORQT

Configurable logic blocks Q/T (see Table 3) 0–1

AND, GATE, INV,

LLD, OR,

PULSETIMER,

SLGAPC,

SRMEMORY,

TIMERSET,

VSGAPC, XOR

Extension logic package (see Table 4) 0–1

FXDSIGN Fixed signal function block 1 1 1 1 1

B16I Boolean 16 to Integer conversion 18 18 18 18 18

BTIGAPC Boolean 16 to Integer conversion with Logic Node

representation

16 16 16 16 16

IB16 Integer to Boolean 16 conversion 18 18 18 18 18

ITBGAPC Integer to Boolean 16 conversion with Logic Node

representation

16 16 16 16 16

TEIGAPC Elapsed time integrator with limit transgression and

overflow supervision

12 12 12 12 12

INTCOMP Comparator for integer inputs 12 12 12 12 12

REALCOMP Comparator for real inputs 12 12 12 12 12

Monitoring

CVMMXN,

VMMXU, CMSQI,

VMSQI, VNMMXU

Measurements 6 6 6 6 6

CMMXU Measurements 10 10 10 10 10

AISVBAS Function block for service value presentation of secondary

analog inputs

1 1 1 1 1

EVENT Event function 20 20 20 20 20

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 15

IEC 61850 ANSI Function description Line Differential

RED670

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

DRPRDRE,

A1RADR-

A4RADR,

B1RBDR-B8RBDR

Disturbance report 1 1 1 1 1

SPGAPC Generic communication function for Single Point indication 64 64 64 64 64

SP16GAPC Generic communication function for Single Point indication

16 inputs

16 16 16 16 16

MVGAPC Generic communication function for Measured Value 24 24 24 24 24

BINSTATREP Logical signal status report 3 3 3 3 3

RANGE_XP Measured value expander block 66 66 66 66 66

SSIMG 63 Gas medium supervision 21 21 21 21 21

SSIML 71 Liquid medium supervision 3 3 3 3 3

SSCBR Circuit breaker monitoring 0-6 3-M13 6-M15 3-M13 6-M15

LMBRFLO Fault locator 1 1 1 1 1

I103MEAS Measurands for IEC 60870-5-103 1 1 1 1 1

I103MEASUSR Measurands user defined signals for IEC 60870-5-103 3 3 3 3 3

I103AR Function status auto-recloser for IEC 60870-5-103 1 1 1 1 1

I103EF Function status earth-fault for IEC 60870-5-103 1 1 1 1 1

I103FLTPROT Function status fault protection for IEC 60870-5-103 1 1 1 1 1

I103IED IED status for IEC 60870-5-103 1 1 1 1 1

I103SUPERV Supervison status for IEC 60870-5-103 1 1 1 1 1

I103USRDEF Status for user defined signals for IEC 60870-5-103 20 20 20 20 20

L4UFCNT Event counter with limit supervision 30 30 30 30 30

TEILGAPC Running hour-meter 9 9 9 9 9

Metering

PCFCNT Pulse-counter logic 16 16 16 16 16

ETPMMTR Function for energy calculation and demand handling 6 6 6 6 6

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

16 ABB

Table 2. Total number of instances for basic configurable logic blocks

Basic configurable logic block Total number of instances

AND 280

GATE 40

INV 420

LLD 40

OR 289

PULSETIMER 40

RSMEMORY 40

SRMEMORY 40

TIMERSET 60

XOR 40

Table 3. Total number of instances for configurable logic blocks Q/T

Configurable logic blocks Q/T

Total number of instances

ANDQT 120

INDCOMBSPQT 20

INDEXTSPQT 20

INVALIDQT 22

INVERTERQT 120

ORQT 120

PULSETIMERQT 40

RSMEMORYQT 40

SRMEMORYQT 40

TIMERSETQT 40

XORQT 40

Table 4. Total number of instances for extended logic package

Extended configurable logic block

Total number of instances

AND 180

GATE 49

INV 180

LLD 49

OR 180

PULSETIMER 59

SLGAPC 74

SRMEMORY 110

TIMERSET 49

VSGAPC 130

XOR 49

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 17

Communication

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

Station communication

LONSPA, SPA SPA communication protocol 1 1 1 1 1

ADE LON communication protocol 1 1 1 1 1

HORZCOMM Network variables via LON 1 1 1 1 1

PROTOCOL Operation selection between SPA and IEC

60870-5-103 for SLM

1 1 1 1 1

RS485PROT Operation selection for RS485 1 1 1 1 1

RS485GEN RS485 1 1 1 1 1

DNPGEN DNP3.0 communication general protocol 1 1 1 1 1

DNPGENTCP DNP3.0 communication general TCP protocol 1 1 1 1 1

CHSERRS485 DNP3.0 for EIA-485 communication protocol 1 1 1 1 1

CH1TCP, CH2TCP,

CH3TCP, CH4TCP

DNP3.0 for TCP/IP communication protocol 1 1 1 1 1

CHSEROPT DNP3.0 for TCP/IP and EIA-485

communication protocol

1 1 1 1 1

MST1TCP,

MST2TCP,

MST3TCP,

MST4TCP

DNP3.0 for serial communication protocol 1 1 1 1 1

DNPFREC DNP3.0 fault records for TCP/IP and EIA-485

communication protocol

1 1 1 1 1

IEC 61850-8-1 Parameter setting function for IEC 61850 1 1 1 1 1

GOOSEINTLKRCV Horizontal communication via GOOSE for

interlocking

59 59 59 59 59

GOOSEBINRCV GOOSE binary receive 16 16 16 16 16

GOOSEDPRCV GOOSE function block to receive a double

point value

64 64 64 64 64

GOOSEINTRCV GOOSE function block to receive an integer

value

32 32 32 32 32

GOOSEMVRCV GOOSE function block to receive a measurand

value

60 60 60 60 60

GOOSESPRCV GOOSE function block to receive a single point

value

64 64 64 64 64

MULTICMDRCV,

MULTICMDSND

Multiple command and transmit 60/10 60/10 60/10 60/10 60/10

FRONT, LANABI,

LANAB, LANCDI,

LANCD

Ethernet configuration of links 1 1 1 1 1

GATEWAY Ethernet configuration of link one 1 1 1 1 1

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

18 ABB

IEC 61850 ANSI Function description Line Differential

RED670

(Customized)

RED670 (A31)

RED670 (B31)

RED670 (A32)

RED670 (B32)

OPTICAL103 IEC 60870-5-103 Optical serial

communication

1 1 1 1 1

RS485103 IEC 60870-5-103 serial communication for

RS485

1 1 1 1 1

AGSAL Generic security application component 1 1 1 1 1

LD0LLN0 IEC 61850 LD0 LLN0 1 1 1 1 1

SYSLLN0 IEC 61850 SYS LLN0 1 1 1 1 1

LPHD Physical device information 1 1 1 1 1

PCMACCS IED Configuration Protocol 1 1 1 1 1

SECALARM Component for mapping security events on

protocols such as DNP3 and IEC103

1 1 1 1 1

FSTACCS

FSTACCSNA

Field service tool access via SPA protocol over

ethernet communication

1 1 1 1 1

ACTIVLOG Activity logging parameters 1 1 1 1 1

ALTRK Service Tracking 1 1 1 1 1

SINGLELCCH Single ethernet port link status 1 1 1 1 1

PRPSTATUS Dual ethernet port link status 1 1 1 1 1

Process bus communication IEC 61850-9-2

1)

PRP IEC 62439-3 parallel redundancy protocol 0-1 1-P03 1-P03 1-P03 1-P03

Remote communication

Binary signal transfer receive/transmit 6/36 6/36 6/36 6/36 6/36

Transmission of analog data from LDCM 1 1 1 1 1

Receive binary status from remote LDCM 6/3/3 6/3/3 6/3/3 6/3/3 6/3/3

Scheme communication

ZCPSCH 85 Scheme communication logic for distance or

overcurrent protection

0-1 1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

ZC1PPSCH 85 Phase segregated scheme communication

logic for distance protection

0-1 1-B05 1-B05

ZCRWPSCH 85 Current reversal and weak-end infeed logic for

distance protection

0-1 1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

1-B11

1-B16

ZC1WPSCH 85 Current reversal and weak-end infeed logic for

phase segregated communication

0-1 1-B05 1-B05

ZCLCPSCH Local acceleration logic 0-1 1-B11 1-B11 1-B11 1-B11

ECPSCH 85 Scheme communication logic for residual

overcurrent protection

0-1 1-C24 1-C24 1-C24 1-C24

ECRWPSCH 85 Current reversal and weak-end infeed logic for

residual overcurrent protection

0-1 1-C24 1-C24 1-C24 1-C24

DTT Direct transfer trip 0-1

1) Only included for 9-2LE products

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

ABB 19

Basic IED functions

Table 5. Basic IED functions

IEC 61850 or function

name

Description

INTERRSIG

SELFSUPEVLST Self supervision with internal event list

TIMESYNCHGEN Time synchronization module

BININPUT, SYNCHCAN,

SYNCHGPS,

SYNCHCMPPS,

SYNCHLON,

SYNCHPPH,

SYNCHPPS, SNTP,

SYNCHSPA

Time synchronization

TIMEZONE Time synchronization

DSTBEGIN,

DSTENABLE, DSTEND

GPS time synchronization module

IRIG-B Time synchronization

SETGRPS Number of setting groups

ACTVGRP Parameter setting groups

TESTMODE Test mode functionality

CHNGLCK Change lock function

SMBI Signal matrix for binary inputs

SMBO Signal matrix for binary outputs

SMMI Signal matrix for mA inputs

SMAI1 - SMAI12 Signal matrix for analog inputs

ATHSTAT Authority status

ATHCHCK Authority check

AUTHMAN Authority management

FTPACCS FTP access with password

SPACOMMMAP SPA communication mapping

SPATD Date and time via SPA protocol

DOSFRNT Denial of service, frame rate control for front port

DOSLANAB Denial of service, frame rate control for OEM port AB

DOSLANCD Denial of service, frame rate control for OEM port CD

DOSSCKT Denial of service, socket flow control

GBASVAL Global base values for settings

PRIMVAL Primary system values

ALTMS Time master supervision

ALTIM Time management

MSTSER DNP3.0 for serial communication protocol

PRODINF Product information

RUNTIME IED Runtime Comp

1MRK 505 346-BEN -

Line differential protection RED670 2.1 IEC

Product version: 2.1

20 ABB

Page is loading ...

ABB Relion REL670 2.1 IEC User manual

This manual is also suitable for

ABB Relion REL670 2.1 IEC User manual

Related papers

Other documents