2. Midmark
  3. Procenter Systems
Procenter Systems

Midmark Procenter Systems, Asepsis 21® Systems, International (Whip) Delivery Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Midmark Procenter Systems Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What are the steps to rotate the delivery unit arm?
    How to adjust the rotational "drag" of the console?
    Which holes should the rotation stop screw be between?
    How to adjust the leveling screws?
    How to make a Chip Air Connection in the delivery head?
1
© Midmark Corporation 2003 SF-1643
KA954503i
2
4
1
3
003-1120-00 Rev. PA2 4/2/2019
Console Mtd. Procenter, Asepsis 21 or
International (Whip) Delivery Unit Installation
Step 1: Remove console side cover.
Step 2: Install console bearing.
Secure with three screws.
Note: Position console bearing so that
set screws are accessible thru holes.
Step 3: Install bearing washer.
Insert mounting post into console bearing.
Step 5:
To adjust rotational “drag”:
Tighten / loosen console
bearing set screws.
Parts Bag Contents
Stop Pins .................... 2
Bearing Washer .......... 1
Screws ....................... 3
Special Tools
Level
Step 4: Rotate arm to verify proper operation.
For LH mtd. console only:
Move rotation stop screw to opposite hole.
Rotate Stop Screw
Note: Procenter delivery unit shown
Style G
2
© Midmark Corporation 2003 SF-1643
2
4
1
3
KA967402i
Equipment Alert
Stop pins must be installed correctly to ensure proper operation.
Step 6: Position delivery unit arms as shown.
(Delivery unit above foot end of chair)
Right Mounted Console
Left Mounted Console
Step 7: Install two stop pins.
Note: Rotation stop screw must be
between two stop pins.
Tip: Move pins under trim ring,
then down into holes.
3
© Midmark Corporation 2003 SF-1643
KA954701i
Step 8: Connect tubing as shown.
(match colors)
Do not remove plug!
4
© Midmark Corporation 2003 SF-1643
Accessories
Step 10: Connect accessory
wire harness to
J4 or J5 on PC Board.
Connect ground wire to
console.
Chair Position Touch Pad
Step 9: Connect touch pad
wire harness to
J2 or J3 on PC Board.
Connect ground from
umbilical.
5
© Midmark Corporation 2003 SF-1643
2
4
1
3
KA967501i
Step 13: Slide cover forward.
Replace end cap.
Step 12: Remove wire tie from lock pawls.
Step 11: Remove flex arm end cap.
Slide cover back.
Step 14: Remove bottom cover.
Step 16: Replace bottom cover.
Step 15: Loosen three button head screws.
Adjust three leveling screws to level unit.
Tighten three button head screws.
Note: Steps 11 - 13 apply to all delivery units. Steps 14 - 16 are Procenter delivery unit only.
6
© Midmark Corporation 2003 SF-1643
Midmark Corporation
60 Vista Drive
P.O. Box 286
Versailles, OH 45380-0286
937-526-3662
Fax 937-526-5542
www.midmark.com
For Units Having Deluxe Rheostat with Chip Air Foot
Controls Only:
Make Chip Air Connection in Delivery Head.
A) Cut green 1/8" Coolant Air Supply tubing.
B) Locate clear 1/8” tubing coming into the unit head.
C) Use barbed tee and sleeves to tee the 1/8" clear tubing
into the 1/8" green coolant air tubing.
Deluxe Rheostat with
Chip Air Foot Control
Chip Air
1/8” Green
1/8” Clear
/