Hubbell Control Solutions NX Typical Product information

  • Hello! I have analyzed the document; it describes various NXFX controllers and NX switches for lighting systems. Key features include dimming control, occupancy sensor integration, and BMS connectivity. I'm ready to help you with any questions about these devices and their configurations.
  • What is the maximum power budget per room controller or in-fixture module?
    Can the buttons on the NX Smart switches be programmed?
    What kind of sensors are supported by the controllers?
    What is the purpose of the NX Bridge Module?
Normal dimming load
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
FX FX SP SP
BA
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
FX FX SP SP
BA
Blue (Test Loop)
ALCR1277
Emergency Light Controller
(Red)
Emergency Pow
Output On
Black
(Green)
Normal Power
Blue (Test Loop)
Purple (Dimmer Loop)
Purple (Dimmer Loop)
White
Red
Red
Gray
Black
CCntrl.
H
N
Normal Dimming
Load 1
H
N
Normal/Emergency
Dimming Load 1
To Optional Remote
Test Switch
+
-
+
-
Gray (-) (0-10VDC)
Violet (+) (0-10VDC)
Gray (-)
Violet (+)
Gray (-)
Violet (+)
Normal/Emergency Switched
Normal/Emergency (Line 120/277 VAC)
Normal/Emergency (Neutral)
Normal/Emergency Power
Neutral
Line
Line
Neutral
SVC
PWRSVC PIN
ON
OFF
NXRCFX - 1RD
FX FX SP SP
BA
TEST SWITCH
EMERGENCY
POWER
UTILITY
POWER
UL924EPC1D-UNV
Emergency Light
Load Controller
1 Black (120V)
2 Orange (277V)
4 White
3 Red
6 Yellow
7 White/Blue
N
Normal Dimming
Load 1 Neutral
Line
N
Normal/Emergency
Dimming Load 1
Line
Neutral
Normal/Emergency (Line -120/277 VAC)
Normal/Emergency Neutral
Normal/Emergency Switched
5 Blue
Select
connection
wire
based on
voltage
Black
Blue
(+0-10V In)
Red
(+0-10V Out)
Cap off
Plenum
Low
Voltage
Wiring
+
-
-
+
Gray (-)
Violet (+)
Gray (-)
Violet (+)
Gray (-) (0-10VDC)
Violet (+) (0-10VDC)
S1. C5
NX Switch Station
Typical Model :
NXSW-ORLO
18 AWG
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
S1. C1
Normal / Emergency dimming load with ALCR1277 Normal / Emergency dimming load with UL924EPCID-UNV
18 AWG
18 AWG
Line 120/270 VAC Line 120V/277 VAC
NXRCFX - 1RD
4x4 JUNCTION
BOX 4x4 JUNCTION
BOX
NXRCFX - 1RD
Normal / Emergency dimming load with UL1008BCELTS1277
NXRCFX - 1RD
FX FX SP SP
BA
H
N
Normal/Emergency
Dimming Load 1
#3 Blue
#12 Blue
#1 Orange
UTILITY
EMERGENCY
STATUS
TEST
SET
#4 White/Blue
#13 White/Blue
UL1008BCELTS1277
16Amps Max.
Normal/Emergency (Line 120/277VAC)
Normal/Emergency Neutral
H
N
Normal Dimming
Load 1
#6 Red/White
#5 Red
+
-
+
-
#9 Yellow
Cap Off
Red Loop (20AWG) for use with a
Normally Closed Maintained
Fire Alarm Switch
#11 White
#2 White
#10 Black
#7 Purple (Out)
#8 Brown (In)
Normal/Emergency Switched
Neutral
Normal Switched
Gray (-) (0-10VDC)
Violet (+) (0-10VDC)
4x4 JUNCTION
BOX
Line 120/277 VAC
Neutral
Normal Switched
Neutral
Normal Switched
18 AWG
18 AWG
Normal/Emergency Power
18 AWG
18 AWG
G
V
H
N
FX FX SP SP
BA
Normal Dimming
Load
18 AWG
Red
White
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Violet
Gray
NXRCFX - 1RD
4x4 JUNCTION
BOX
4x4 JUNCTION
BOX
Line Voltage
Receptacles
NXRC-1R
BA
CAT5/6 Cable
Normal dimming load and receptacle load
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
FX FX SP SP
BA
NXRCFX - 1RD
4x4 JUNCTION
BOX
Reverse phase
Load
PHDIM-1277
Violet
Gray
Purple
Gray
White
N
Red
Gray
Black
H
Red
JUNCTION
BOX
(OPTIONAL)
JUNCTION
BOX
Switched Hot
18 AWG
Reverse phase load
Networked normal / emergency dimming load on NX UL924 room controller
NXRCFX-1RD
BA
4x4 JUNCTION
BOX
Neutral
Red
White Neutral
Switched Hot
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
FX FX SP SP
BA
18-22 AWG
NXRCFX - 1RD
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
Networked normal / emergency dimming load on NX UL924 room controller and receptacle load
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
FX FX SP SP
BA
18 AWG
NXRCFX - 1RD
NXRM-H
Networked normal dimming load
S1. C6 S1. C7
S1. C8 S1. C9
S1. C11
S1. C2
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
H
H
12 AWG
12 AWG
12 AWG
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
12 AWG
18 AWG
18 AWG
Normal/Emergency
Power
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
Ground
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NX Switch Station
Typical Model :
NXSW-ORLO
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Line Voltage
Receptacles
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120/277 VAC)
White (Neutral)
12 AWG
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
12 AWG
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
White (Neutral)
18 AWG
CAT5/6 Cable
4x4 JUNCTION
BOX
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
NXRC-UL924-UNV
Normal / Emergency Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped Cap Off
12 AWG
Normal/Emergency
Dimming Load
12 AWG
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
White (Neutral)
18 AWG
CAT5/6 Cable
4x4 JUNCTION
BOX
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
NXRC-UL924-UNV
Normal / Emergency Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped Cap Off
12 AWG
Normal/Emergency
Dimming Load
12 AWG
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
FX FX SP SP
BA
18 AWG
NXRCFX - 1RD
12 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
12 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
Black
White
Red
Red
Gray
Black
16 AWG
12 AWG
12 AWG
16 AWG
16 AWG
16 AWG
18 AWG
12 AWG
18 AWG
12 AWG
12 AWG
12 AWG
UL1008BCELTS1277
The Gauge number near to lead numbers and
lead color of this device are the gauge size of
wires coming out of the device. Please refer to
specification and install cut sheets.
ALCR1277
The Gauge number near to lead color of this
device are the gauge size of wires coming out
of the device. Please refer to specification and
install cut sheets.
Violet
Gray
Violet
Gray
Violet
Gray
18 AWG
16 AWG
16 AWG
12 AWG
12 AWG
18 AWG
18 AWG
12 AWG
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
NX SMART PORT
NX SMART PORT
J1
J2
Pilot
Input 2
Input 1
+24V1:
2:
3:
4:
12
3
4
NXCI
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
FX FX SP SP
BA
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
18 AWG
NXRCFX - 1RD
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
12 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
To Additional NX room devices
Violet
Normal Dimming
Load Gray
Red
White
G
V
H
N
4x4 JUNCTION
BOX
FX FX SP SP
BA
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
18 AWG
NXRCFX - 1RD
12 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
Normal dimming load with key switch
S1. C3 Normal dimming load with integration to BMS systems
S1. C4
Normal Power
S1. C10
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
Normal Switched
Normal Neutral
Normal Switched
Normal Neutral
Normal Switched
Normal Neutral
Normal/Emergency Neutral
12 AWG
12 AWG
12 AWG
18 AWG
12 AWG
12 AWG
12 AWG 12 AWG 12 AWG
12 AWG
12 AWG
12 AWG 12 AWG
12 AWG
12 AWG
LVSKEY-3M-SS
Black/White
Black
Blue (CCW)
Blue /White (CW)
Normally Open
Common
Normally Closed
1 AMP 24 VOLTS
AC OR DC
NXRO
Dry Contact
Output HVAC Panel
or any other BMS
Systems
Example of a BMS System
NX SMART PORT
NX SMART PORT
J1
J2
Common
18 AWG
18 AWG
CAT5/6 Cable
Neutral
Line
Line
Neutral
(As required)
(As required)
(As required) (As required)
(As required)
(As required)
(As required)
(As required)
(As required)
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
(As required)
(As required)
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
CAT5/6 Cable
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Ground
Ground
CAT5/6 Cable
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
HubbNET Network
HubbNET Network
HubbNET Network
HubbNET Network
Notes
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
----Blank----
----Blank----
Gray
Violet
FX FX SP SP
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
07/06/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
NXFX CONTROLLERS WITH SINGLE LOAD
HCS - NX - S1
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
05/20/21 AJ
B
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
SVC
PWRSVC PIN
ON
OFF
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
H1
N
Normal Dimming
Load 1
N
Normal/Emergency
Dimming Load 1
+
-
+
-
Gray (-) (0-10VDC)
Violet/Striped (+) (0-10VDC)
Gray (-)
Violet (+)
Gray (-)
Violet (+)
Normal/Emergency Switched
Normal/Emergency (Line 120/277 VAC)
Normal/Emergency (Neutral)
Normal/Emergency Power
Line
Neutral
Normal Switched (Red)
18 AWG
18 AWG
Line 120/270 VAC
Neutral
Normal Switched (Red)
18 AWG
12 AWG
12 AWG
N
Normal Dimming
Load 2
+
-
Gray (-)
Violet/Striped(+)
Line
Neutral
Normal Switched (Blue)
18 AWG 12 AWG
Violet (+) (0-10VDC)
H
Neutral
Line
H2
Violet
Violet/Striped
Gray
TEST SWITCH
EMERGENCY
POWER
UTILITY
POWER
UL924EPC1D-UNV
Emergency Light
Load Controller
1 Black (120V)
2 Orange (277V)
4 White
3 Red
6 Yellow
7 White/Blue
5 Blue
Select
connection
wire
based on
voltage
Black
Blue
(+0-10V In)
Red
(+0-10V Out)
Cap off
Plenum
Low
Voltage
Wiring
S2. C8
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
SVC
PWRSVC PIN
ON
OFF
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
H1
N
Normal Dimming
Load 1
N
Normal/Emergency
Dimming Load 1
+
-
+
-
Gray (-) (0-10VDC)
Violet/Striped (+) (0-10VDC)
Gray (-)
Violet (+)
Gray (-)
Violet (+)
Normal/Emergency Switched
Line
Neutral
Normal Switched (Red)
18 AWG
18 AWG
Line 120/270 VAC
Neutral
Normal Switched (Red)
18 AWG
12 AWG
N
Normal Dimming
Load 2
+
-
Gray (-)
Violet/Striped(+)
Line
Neutral
Normal Switched (Blue)
18 AWG 12 AWG
Violet (+) (0-10VDC)
H
Neutral
Line
H2
Violet
Violet/Striped
Gray
#3 Blue
#12 Blue
#1 Orange
UTILITY
EMERGENCY
STATUS
TEST
SET
#4 White/Blue
#13 White/Blue
UL1008BCELTS1277
16Amps Max.
Normal/Emergency (Line 120/277VAC)
Normal/Emergency Neutral
#6 Red/White
#5 Red
#9 Yellow
Cap Off
Red Loop (20AWG) for use with a
Normally Closed Maintained
Fire Alarm Switch
#11 White
#2 White
#10 Black
#7 Purple (Out)
#8 Brown (In)
12 AWG
Normal/Emergency
Power
18 AWG
12 AWG
18 AWG
12 AWG
12 AWG
12 AWG
18 AWG
16 AWG
16 AWG
12 AWG
12 AWG
18 AWG
18 AWG
12 AWG
UL1008BCELTS1277
The Gauge number near to lead numbers and
lead color of this device are the gauge size of
wires coming out of the device. Please refer to
specification and install cut sheets.
Normal/Emergency Neutral
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
Reverse phase
Load 1
PHDIM-1277
White
N
Red
Gray
Black
Switched Hot (Red)
Neutral
12 AWG
Reverse phase
Load 2
PHDIM-1277
White
N
Blue
Gray
Black
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
12 AWG
Neutral
JUNCTION
BOX
(OPTIONAL)
JUNCTION
BOX
Gray
Gray
Purple
GrayGray
Violet/Striped Violet
Switched Hot (Blue)
White (Neutral)
Purple
H2
12 AWG
H1
18 AWG
18 AWG
JUNCTION
BOX
(OPTIONAL)
S2. C6 Dual reverse phase load
Normal dimming load
S2. C1 Networked normal dimming load
S2. C2
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Normal Power
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Black (Line 120/277/347 VAC)
White (Neutral)
-
N
Class 2 Driver with Max
Current of 2.5A
Red
White
H
+
+
-
+
-
CTC (Optional)
+
-
+
-
+
-
Driver
Output
0-10V
Input
0-10V
Input
Driver
Input
CH2 (+)
CH1 (+)
CH2 (+)
CH1 (+)
56VDC
Max Output
LED
Dimming Driver
(Constant Current)
For SpectraSync applications, the
highest CCT LED should be on CH1 and
the lower CCT LED should be on CH2.
Violet
Gray
Violet / Striped
Cap Off
Blue
12 AWG
18 AWG
Networked normal dimming load with CCT control
S2. C3
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
To Additional NX room Devices
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
Normal dimming load with key switch
S2. C4
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
Normally Open
Common
Normally Closed
1 AMP 24 VOLTS
AC OR DC
NXRO
Dry Contact
Output HVAC Panel
or any other BMS
Systems
Example of a BMS System
Normal dimming load with integration to BMS systems
S2. C5
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
SVC
PWRSVC PIN
ON
OFF
CAT5/6 Cable
SVC PIN
SVC
PWR
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Blue (Test Loop)
ALCR1277
Emergency Light Controller
(Red)
Emergency Pow
Output On
Black
(Green)
Normal Power
Blue (Test Loop)
Purple (Dimmer Loop)
Purple (Dimmer Loop)
White
Red
Red
Gray
Black
CCntrl.
H1
N
Normal Dimming
Load 1
N
Normal/Emergency
Dimming Load 1
To Optional Remote
Test Switch
+
-
+
-
Gray (-) (0-10VDC)
Violet/Striped (+) (0-10VDC)
Gray (-)
Violet (+)
Gray (-)
Violet (+)
Normal/Emergency Switched
Normal/Emergency (Line 120/277 VAC)
Normal/Emergency (Neutral)
Normal/Emergency Power
Line
Neutral
Normal Switched (Red)
18 AWG
18 AWG
Line 120/270 VAC
Neutral
Normal Switched (Red)
18 AWG
12 AWG
N
Normal Dimming
Load 2
+
-
Gray (-)
Violet/Striped(+)
Line
Neutral
Normal Switched (Blue)
18 AWG 12 AWG
Violet (+) (0-10VDC)
H
Neutral
Line
H2
Violet
Violet/Striped
Gray
16 AWG
12 AWG
12 AWG
16 AWG
16 AWG
16 AWG
ALCR1277
The Gauge number near to lead color of this
device are the gauge size of wires coming out
of the device. Please refer to specification and
install cut sheets.
Normal Neutral
Normal Neutral
Normal / Emergency dimming load with ALCR1277S2. C7 Normal / Emergency dimming load with UL924EPC1D-UNV
Normal Neutral
Normal Neutral
Normal Neutral
Normal Neutral
Normal / Emergency dimming load with UL1008BCELTS1277 Normal dimming and receptacle load
S2. C10S2. C9
Networked normal / emergency dimming load on NX UL924 room controller
S2. C11 Networked normal / emergency dimming load on NX UL924 room controller and receptacle load
S2. C12
4x4 JUNCTION
BOX
Line Voltage
Receptacles
NXRC-1R
BA
CAT5/6 Cable
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
12 AWG
12 AWG
12 AWG
12 AWG
12 AWG
12 AWG 12 AWG
12 AWG 12 AWG
NX SMART PORT
NX SMART PORT
J1
J2
Pilot
Input 2
Input 1
+24V1:
2:
3:
4:
12
3
4
NXCI
Black/White
Black
Blue (CCW)
Blue /White (CW)
NX SMART PORT
NX SMART PORT
J1
J2
Common
18 AWG
18 AWG
LVSKEY-SS
12 AWG
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
(As required)
NXRM-H
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NX Switch Station
NXSW-CCT
SVC
PWRSVC PIN
FOCUS
WORK
NORMAL
CALM
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
(As required)
NXRM-H
CAT5/6 Cable
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
(As required)
JUNCTION
BOX
(As required)
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Ground
CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
Notes
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
----Blank----
----Blank----
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
CAT5/6 Cable
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
Normal Dimming
Load 1
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
Normal Dimming
Load 2
White (Neutral)
18 AWG
NXRC-1R
BA
4x4 JUNCTION
BOX
CAT5/6 Cable
Line Voltage
Receptacles
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
CAT5/6 Cable
Ground
N
H1
V1
GViolet
Gray
Red
White
White (Neutral)
18 AWG
CAT5/6 Cable
4x4 JUNCTION
BOX
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
NXRC-UL924-UNV
Normal / Emergency Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped Cap Off
12 AWG
Normal/Emergency
Dimming Load
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable CAT5/6 Cable
HubbNET Network
HubbNET Network
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
CAT5/6 Cable
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
Normal Dimming
Load 1
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
Normal Dimming
Load 2
White (Neutral)
18 AWG
N
H1
V1
GViolet
Gray
Red
White
White (Neutral)
18 AWG
CAT5/6 Cable
4x4 JUNCTION
BOX
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
NXRC-UL924-UNV
Normal / Emergency Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped Cap Off
12 AWG
Normal/Emergency
Dimming Load
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable CAT5/6 Cable
HubbNET Network
HubbNET Network
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
07/22/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
NXFX CONTROLLERS WITH DUAL LOAD (PART-1)
HCS - NX - S2
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
05/20/21 AJ
B
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Normal Power
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NX Switch Station
NXSW-CCT
Black (Line 120/277/347 VAC)
White (Neutral)
-
N
Class 2 Driver with Max
Current of 2.5A
Red
White
H
+
+
-
+
-
CTC (Optional)
+
-
+
-
+
-
Driver
Output
0-10V
Input
0-10V
Input
Driver
Input
CH2 (+)
CH1 (+)
CH2 (+)
CH1 (+)
56VDC
Max Output
LED
Dimming Driver
(Constant Current)
For SpectraSync applications, the
highest CCT LED should be on CH1 and
the lower CCT LED should be on CH2.
Violet
Gray
Violet / Striped
Cap Off
Blue
12 AWG
18 AWG
SVC
PWRSVC PIN
FOCUS
WORK
NORMAL
CALM
12 AWG
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Normal Power
CAT5/6 Cable
NX Switch Station
NXSW-CCT
Black (Line 120/277/347 VAC)
White (Neutral)
-
N
Class 2 Driver with Max
Current of 2.5A
Red
White
H
+
+
-
+
-
CTC (Optional)
+
-
+
-
+
-
Driver
Output
0-10V
Input
0-10V
Input
Driver
Input
CH2 (+)
CH1 (+)
CH2 (+)
CH1 (+)
56VDC
Max Output
LED
Dimming Driver
(Constant Current)
For SpectraSync applications, the
highest CCT LED should be on CH1 and
the lower CCT LED should be on CH2.
Violet
Gray
Violet / Striped
Cap Off
Blue
12 AWG
18 AWG
SVC
PWRSVC PIN
FOCUS
WORK
NORMAL
CALM
12 AWG
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
4x4 JUNCTION
BOX
Line Voltage
Receptacles
NXRC-1R
BA
Red
White
Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
NX Bridge Module
NXHNB2
12 AWG
CAT5/6 Cable
CAT5/6 Cable
Networked room controllers with CCT control and receptacle load
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
CAT5/6 Cable
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
Normal Dimming
Load 1
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
Normal Dimming
Load 2
White (Neutral)
18 AWG
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NX SMART PORT
RS232
SERIAL COM
NXAVM
NX SMART PORT
NX SMART PORT
J1
J2
Pilot
Input 2
Input 1
+24V1:
2:
3:
4:
12
3
4
NXCI
Black (Input 1)
Brown (+24V)
Blue (Pilot)
NXWPS
NXSW-TH3
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
White (Neutral)
18 AWG
NX SMART PORT
RS232
SERIAL COM
NXAVM
NXSW-TH3
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Wall / Partition Wall / Partition Wall / Partition
Networked room controllers with partition sensor S3. C2S3. C1
Normal Dimming
Load 1
Normal Dimming
Load 2
S3. C3
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
SVC
PWRSVC PIN
ON
OFF
NXRM-H
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
SVC
PWRSVC PIN
ON
OFF
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
S3. C4
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
SVC
PWRSVC PIN
ON
OFF
Yellow
SVC PIN
SVC
PWR
NXBTC
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
Red 24VDC
Black
Yellow
RJ45 Adapter
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
Normal dimming networked load Normal dimming load Normal dimming with NXBTCS3. C5 S3. C6 Daylight sensor controlled normal dimming load
S3. C7
12 AWG 12 AWG
12 AWG 12 AWG 12 AWG
18 AWG
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
CAT5/6 Cable
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
Normal Dimming
Load 1
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
Normal Dimming
Load 2
White (Neutral)
18 AWG
S3. C8
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
12 AWG
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
CAT5/6 Cable
18 AWG
CAT5/6 Cable
NX Bridge Module
NXHNB2
N
H1
V1
GViolet
Gray
Red
White
HubbNET Network
HubbNET Network
CAT5/6 Cable
4x4 JUNCTION
BOX
Normal Power
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped
12 AWG
Normal Dimming
Load 1
12 AWG
FX FX SP SP
BA
NXRCFX - 2RD
White (Neutral)
N
H1
V1
G
Gray
Red
White
18 AWG
12 AWG
Normal Dimming
Load 2
White (Neutral)
18 AWG
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
12 AWG
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
CAT5/6 Cable
18 AWG
CAT5/6 Cable
Owner supplied PC with
Web Browser
Ethernet
NXAC
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Hot
Blue (Control)
Black (Common)
Neutral
Ground
120 VAC
HCSREC-F
18 AWG
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
Yellow
RJ45 Adapter
Red 24VDC
Blue
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
S3. C9 Normal dimming with controlled receptacle S3. C10
CAT5/6 Cable
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
Violet/Striped
Cap Off
CAT5/6 Cable
RJ45 Adapter
R
HUBBELL
Building
Automation
+
-
OCC
PC
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
(Additonal sensors if required)
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
18 AWG
CAT5/6 Cable
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
4x4 JUNCTION
BOX
NXRC-UL924-UNV
Violet
Gray
Red
White
G
V
H
N
18 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
12 AWG
Normal /
Emergency Power
Normal/Emergency
Dimming Load
4x4 JUNCTION
BOX
FX FX SP SP
BA
NXRCFX - 2RD
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
G
V1
H1
N
N
H2
V2
G
Normal Dimming
Load 1
Normal Dimming
Load 2
Violet
Gray
Red
White
Gray
White
Blue
Violet/Striped
12 AWG
18 AWG
12 AWG
Neutral
12 AWG
12 AWG 12 AWG
Normal/Emergency dimming load on NX UL924 room controller
Networked room controllers with NX area controller
CAT5/6 Cable
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
Occupancy sensor controlled normal dimming load
SVC
PWRSVC PIN
ON
OFF
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-ORLO
NX Switch Station
Typical Model :
NXSW-6
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
(As required)
Refer to Detail-5
in drawing no.
HCS - NX - S4
(As required)
(As required) (As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
(As required)
(As required)
(As required)
(As required) (As required) (As required)
(As required)
(As required)
(As required)
(As required) (As required)
(As required)
(As required)
(As required)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable CAT5/6 Cable CAT5/6 Cable CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable CAT5/6 Cable
Ground
CAT5/6 Cable NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S4
CAT5/6 Cable CAT5/6 Cable CAT5/6 Cable CAT5/6 Cable
HubbNET Network
HubbNET Network
HubbNET Network
HubbNET Network HubbNET Network
HubbNET Network
HubbNET Network
HubbNET Network
CAT5/6 Cable
Notes
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
----Blank----
----Blank----
Yellow
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
07/23/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
NXFX CONTROLLERS WITH DUAL LOAD (PART-2)
HCS - NX - S3
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
05/20/21 AJ
B
Notes
NXFM-1R2D-O-UNV
Gray (-)
Violet/White (+) CH 2
Black (Line 120/277/347 VAC)
Normal Power
Red
White
Black
Test Button
Test LED
Violet (+) Ch 1
0-10v Dimming
18 AWG
12 AWG
12 AWG
NXRM-H
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXFSP
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
CAT5/6 Cable
NXCBL Cable
NX fixture module (Offset) with dual drivers
S4. C1
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXFSP
CAT5/6 Cable
NXCBL Cable
Test LED
Test Button
NXFM-1R2D-I-UNV
Gray (-)
Violet/White (+) CH 2
Violet (+) Ch 1
Black
White
Red
0-10v Dimming
LED Dimming
Driver 2
N
H
+H
NLED Dimming
Driver 1
-
-
+
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
12 AWG
18 AWG12 AWG
NX fixture module (Inline) with dual driversS4. C2
Violet (+) Ch 1
Violet/White (+) CH 2
Common
+12V
COM
Dim2
Dim1
Test LED
NXFM-LV
Test Button
+12 VDC
LED Dimming
Driver 2
N
H
+H
NLED Dimming
Driver 1
-
-
+
LED Dimming
Driver 1
COM
+
H
N
+12V
LED Dimming
Driver 2
COM
+
H
N
+12V
Black (Line)
White (Neutral)
Black (Line)
White (Neutral)
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXFSP
CAT5/6 Cable
NX fixture module (Low Voltage) with dual driversS4. C3
Cap Off
Black (Line In)
White (Neutral/Line 2 In)
Red (line Out)
Violet (0-10V) + Out
Gray (0-10V) - GND Out
Brown (24VDC)
Orange (Digital In 3-30VDC)
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
Violet Normal Dimming
Load
Gray
Red
White
G
V
H
N
Blue (Control)
Red
Black
Normal Power
Line 120/277/347/480 VAC
Neutral
NX on-fixture module (7 Pin)
POWERED
HubNET
NETWORK
NON
POWERED
ETHERNET
NETWORK
432 1
5DC IN
Solid State Drive
See Side Profile
View A for Detail
Mother Board
Power Supply
Profile View
Detail A
See Side Profile
View B for Detail
Profile View
Detail B
DB-15HD, 15-pin
(Not Used)
6-pin female
mini DIN
DVI Video
(Not Used)
DB-9, 9-pin male
(Not Used)
PC/Network Connection
Miniplug(s)
(Not Used)
USB
(4-Typical)
RJ-45, 8-pin female
RJ-45 connection between Port
1 and Mother Board RJ-45 Port
MB-5 (Detail B) RJ-45 connection between this
Port and Port 1 on Detail A
Battery for Clock Back-up
e-SATA Connector
(Connects to Hard Drive)
MB-6
MB-5
MB-4
MB-3
MB-2
MB-1
MB-6
MB-5
MB-4
MB-3
MB-2
MB-1
12V Power to
MotherBoard
High Voltage
Compartment
12V
24V IN
5V
Use for HUBBNET connection to NX Panels
only. This port does not supply power to the
network.
Use for HUBBNET connections to NX panels
or NXHNB bridges. This port supplies power
to the network.
Detail-5: NXAC
Details
Note:
1. To connect an NXSMP sensors or NXRM-H radio to a T568B standard CAT5/6 cable using an
RJ45 connector it is necessary to use the NXCBL-P-10 plenum accessory cable to bridge the
sensor to the CAT5/6 connector.
2. NXSMP sensors and NXRM-H radios have two connection terminals to achieve daisy chaining
to other NXFX devices.
NXCBL-P-10
CAT5/6 Cable
NXSMP or NXRM-H
Detail-1 : NXRM-H/NXSMP to CAT5/6 cable
4x4 JUNCTION
BOX NXRC-1R
BA
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
NX Bridge Module
NXHNB2
NXRM-H
CAT5/6 Cable
N
Normal
Load
Red
White
H
12 AWG
Owner supplied PC with Web
Browser
Ethernet
NXFM-1R2D-O-UNV
Gray (-)
Violet/White (+) CH 2
Black (Line 120/277/347 VAC)
Normal Power
Red
White
Black
Test Button
Test LED
Violet (+) Ch 1
0-10v Dimming
18 AWG12 AWG
12 AWG
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
NXFSP
NXCBL Cable
LED Dimming
Driver 2
N
H
+H
NLED Dimming
Driver 1
-
-
+
NXRM-H
NXFM-1R2D-O-UNV
Gray (-)
Violet/White (+) CH 2
Black (Line 120/277/347 VAC)
Normal Power
Red
White
Black
Test Button
Test LED
Violet (+) Ch 1
0-10v Dimming
18 AWG
12 AWG
12 AWG
Low Voltage
Occupancy Sensor
Typical Model :
NXSMP-OMNI
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
NXFSP
NXCBL Cable
LED Dimming
Driver 2
N
H
+H
NLED Dimming
Driver 1
-
-
+
NXRM-H
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
Refer to Detail-6
for NX-8 details
on drawing
(HCS-NX-S7)
NX-Panel
Typical Model : NXP2-8
HubbNET Network HubbNET Network
Detail-6:Detail-2 : NXOFM
Compliant with:
ANSI C136-41 (7& 5 pin) twist-lock receptacles.
Receptacle not included.
Bottom View
Refer to Detail-2
in this drawing
(HCS-NX-S4)
S4. C9
To NX network / Next Fixture
as applicable
To NX network / Next Fixture
as applicable
To NX network / Next Fixture
as applicable
Owner supplied PC with Web
Browser
Ethernet
NXAC
NX-EOF-MC-01
PoE 1
MODE A
48 V
24 V
MODE B
48 V
24 V
PoE 2 PoE 3 PoE 4 PoE 5 PoE 6 PoE 7
UP LINK
NXPOE7-24B
4x4 JUNCTION
BOX
NX Bridge Module
NXHNB2
Connection to Non Powered Ethernet Port of NXAC
Connection to Uplink Port
Black (Line 120 VAC)
White (Neutral)
AC Adapter
5-12 VDC
HubbNET Network HubbNET Network
Next Building
Building -1 Building -2
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
Wireless network of NX devices with NX area controller and panels
4x4 JUNCTION
BOX
NX Bridge Module
NXHNB2
HubbNET Network
PoE 1
MODE A
48 V
24 V
MODE B
48 V
24 V
PoE 2 PoE 3 PoE 4 PoE 5 PoE 6 PoE 7
UP LINK
NXPOE7-24B
To NX network of Building 2
To NX network of Building 1
NX-EOF-MC-01
Black (Line 120 VAC)
White (Neutral)
AC Adapter
5-12 VDC
Next Building
Next Building
Copper Ethernet
Copper Ethernet
Network of NX devices between two separate building units via fiber cable and media converter
Fiber
Fiber
Yellow
White (Neutral)
White (Neutral)
White (Neutral)
NXAC
NX-Panel
Typical Model : NXP2-8
Building Automation
HUBBELL HUBBELL
R
HubbNET Network
Photo Sensor
(LUXSTATLS)
Pin 1
Pin 2
Pin 3
Pin 4
LED
COMMON
CONTROL
+24VDC
Pin 1
Pin 2
Pin 3
Pin 4
NORMALLY OPEN
COMMON
COMMON
NORMALLY CLOSED
Pin 1
Pin 2
Pin 3
Pin 4
Detail-3 : NXDCIO
Refer to Detail-3
in this drawing
(HCS-NX-S4)
Red 24VDC
Black
SVC
PWRSVC PIN
LVSM2PL
Switch Station
Black
Blue
Gray
Black/White
Blue/White
Gray/White
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
Red 24VDC
NXDCIO with NXHDI
S4. C5
NXHDI NXDCIO
Blue
Black
Red 24VDC
Blue
Black
S4. C4
S4. C8
18 AWG
18 AWG
Details Details Details
Building Automation
HUBBELL HUBBELL
R
Red 24VDC
Black
R
HUBBELL
Building
Automation
+
-
OCC
PC
18 AWG RJ45 Adapter
Neutral
Line 100-270 VAC
NXHDI NXSP
HubbNET Network
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
SVC PIN
SVC
PWR
NX Switch Station
Typical Model :
NXSW-6
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
Yellow
NXSP with NXHDIS4. C6
NXHDI required for connection to HubbNET network
(DIN rail devices typically located in NXENC-D)
4x4 JUNCTION
BOX NXRC-1R
BA
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
NX Bridge Module
NXHNB2
NXRM-H
N
Normal
Load
Red
White
H
12 AWG
Ethernet
NXAC
Refer to Detail-5
in this drawing
(HCS-NX-S4)
Networked controller connected to NX area controller
S4. C7
+S-VOUT
ADJ
DC
LO
DC
OK
NL
DSP
30-24/277A
NXPWRSPLY
Red
White
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
Yellow
RJ45 Adapter
Red 24VDC
Blue
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
drawing
CAT5/6 Cable
Neutral
Line 100-270 VAC
+S-VOUT
ADJ
DC
LO
DC
OK
NL
DSP
30-24/277A
NXPWRSPLY
Red
White
NOTES:
1. Four (4) ports total, each with two (2) RJ45 connectors.
Upper and lower RJ45 port connectors are internally
connected in parallel
2. Maximum power budget per SmartPort module = 32
Loads
Switch station = 1 Load
PIR only Occupancy sensor = 1 Load
PIR only Occupancy sensor with RP option = 2 Loads
Dual Technology and Ultrasonic Occupancy sensor = 3
Loads
Dual Technology and Ultrasonic Occupancy sensor with
RP option = 4 Loads
Daylight Sensor (photocell) = 1 Load
3. The entire power budget can be used on one (1) port or
distributed across all four (4) ports
4. Only one (1) Daylight Sensor is supported per port, four
(4) maximum per SmartPort Module
5. Multiple Occupancy Sensors can be connected to a single
port, but all will be programmed into a single Zone. The
SmartPort Module supports a maximum of four (4)
Occupancy Zones total regardless of the number of
Occupancy Sensors connected.
6. A maximum of eight (8) Smart Switches can be connected
to each port (32 maximum per module) and my share a
port with a Daylight Sensor or Occupancy Sensor(s)
7. NXPWRSPLY power supply is required for each location if
more than one (1) SmartPort module total is connected
to the HubbNET network wire
Refer to Detail-4
in this drawing
(HCS-NXS-S4)
Owner supplied PC with Web
Browser
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing power
budget of controller.
Please refer to notes section in this
drawing
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NXFM-O
Max Power budget
per NXFM-O is 30
NXFM-I
Max Power budget
per NXFM-I is 30
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing power
budget of controller.
Please refer to notes section in this
drawing
NXFM-O
Max Power budget
per NXFM-O is 30
NXFM-O
Max Power budget
per NXFM-O is 30
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NXFM- LV
Max Power budget
per NXFM-LV is
depended on the
driver powering the
NXFM-LV
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing power
budget of controller.
Please refer to notes section in this
drawing
HubbNET Network
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
Photo Sensor
NXDS
NXOFM
The on-fixture module is intended to control a
single fixture.
Control input devices connecting to the NXOFM
do not support SmartPORT connections.
Available power for control input devices is
based on the luminaire driver capacity.
Detail-4 : NXSP
NXHDI required for connection to HubbNET network
(DIN rail devices typically located in NXENC-D)
(As required)
(As required)
(As required) (As required)
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-ORLO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
drawing
NXRM-H
NXRM-H
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
CAT5/6 Cable
HubbNET Network
CAT5/6 Cable
HubbNET Network
CAT5/6 Cable CAT5/6 Cable CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
CAT5/6 CableCAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
NXCBL Cable
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S4)
Refer to Detail-5
in this drawing
(HCS-NX-S4)
Refer to Detail-5
in this drawing
(HCS-NX-S4)
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
CAT5/6 Cable
----Blank----
----Blank----
----Blank----
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
08/04/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
OTHER NX DEVICES
HCS - NX - S4
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
02/18/21 AJ
A05/20/21 AJ
B
BA
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
4x4 JUNCTION
BOX
SVC
PWRSVC PIN
ON
OFF
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
NX Switch Station
Typical Model :
NXSW-4
NXBTC
CAT5/6 Cable
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
H
12 AWG 12 AWG
Normal
Load
Red
White
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
SVC
PWRSVC PIN
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
Violet/Striped
Cap Off
4x4 JUNCTION
BOX
NXRC-UL924-UNV
Violet
Gray
Red
White
G
V
H
N
18 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
12 AWG
Normal /
Emergency Power
Normal/Emergency
Dimming Load
12 AWG
Normal / Emergency Dimming load on NXRC-UL924 Room Controller
CAT5/6 Cable
NX Bridge Module
NXHNB2
HubbNET NetworkHubbNET Network
CAT5/6 Cable
4x4 JUNCTION
BOX
BA
CAT5/6 Cable
BA
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
SVC
PWRSVC PIN
ON
OFF
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
NX Switch Station
Typical Model :
NXSW-4
N
H
12 AWG
Normal
Load
Red
White
SVC
PWRSVC PIN
Networked Normal / Emergency Dimming load on NXRC-UL924 Room Controller
R
HUBBELL
Building
Automation
+
-
OCC
PC
BA
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
S5. C1 Normal switching load
N
Normal
Load
Red
White
H
12 AWG
SVC
PWRSVC PIN
ON
OFF
BA
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
4x4 JUNCTION
BOX
SVC
PWRSVC PIN
ON
OFF
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : WSPSM24V
18 AWG
Normal switching load with WASP Sensor
BA
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
4x4 JUNCTION
BOX
SVC
PWRSVC PIN
ON
OFF
Normal switching load with NXBTC
CAT5/6 Cable R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NXBTC
CAT5/6 Cable
R
HUBBELL
Building
Automation
+
-
OCC
PC
BA
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
NXRC- 1R
4x4 JUNCTION
BOX
BA
NXRC- 1R
4x4 JUNCTION
BOX
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
Blue (Test Loop)
ALCR1277
Emergency Light Controller
(Red)
Emergency Pow
Output On
Black
(Green)
Normal Power
Blue (Test Loop)
Purple (Dimmer Loop)
Purple (Dimmer Loop)
White
Red
Red
Gray
Black
CCntrl.
H
N
Normal
Load 1
H
N
Normal/Emergency
Load 1
To Optional Remote
Test Switch
Normal/Emergency Switched
Normal/Emergency (Line 120/277 VAC)
Normal/Emergency (Neutral)
Normal/Emergency Power
Neutral
Line
Line
Neutral
Line 120/270 VAC
Neutral
Normal Switched
12 AWG
Black (Line 120/277 VAC)
White (Neutral)
12 AWG
Normal Power
Black
White
Red
Red
Gray
Black
16 AWG
12 AWG
12 AWG
16 AWG
16 AWG
16 AWG
Normal Switched
Normal Neutral
12 AWG
12 AWG
Normal / Emergency load with ALCR1277
12 AWG
BA
NXRC- 1R
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
TEST SWITCH
EMERGENCY
POWER
UTILITY
POWER
UL924EPC1D-UNV
Emergency Light
Load Controller
1 Black (120V)
2 Orange (277V)
4 White
3 Red
6 Yellow
7 White/Blue
Normal/Emergency (Line -120/277 VAC)
Normal/Emergency Neutral
Normal/Emergency Switched
5 Blue
Select
connection
wire
based on
voltage
Black
Blue
(+0-10V In)
Red
(+0-10V Out)
Cap off
Plenum
Low
Voltage
Wiring
Line 120V/277 VAC
Neutral
Normal Switched
Normal/Emergency Power
12 AWG
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
Normal / Emergency load with UL924EPC1D-UNV
BA
NXRC- 1R
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
H
N
Normal/Emergency
Load 1
#3 Blue
#12 Blue
#1 Orange
UTILITY
EMERGENCY
STATUS
TEST
SET
#4 White/Blue
#13 White/Blue
UL1008BCELTS1277
16Amps Max.
Normal/Emergency (Line 120/277VAC)
Normal/Emergency Neutral
H
N
Normal
Load 1
#6 Red/White
#5 Red
#9 Yellow
Cap Off
Red Loop (20AWG) for use with a
Normally Closed Maintained
Fire Alarm Switch
#11 White
#2 White
#10 Black
#7 Purple (Out)
#8 Brown (In)
Normal/Emergency Switched
Neutral
Normal Switched
4x4 JUNCTION
BOX
Line 120/277 VAC
12 AWG
Normal/Emergency
Power
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
18 AWG
12 AWG
18 AWG
12 AWG
12 AWG
12 AWG
18 AWG
16 AWG
16 AWG
12 AWG
12 AWG
18 AWG
18 AWG
12 AWG
Normal Switched
Normal Neutral
Normal/Emergency Neutral
12 AWG
12 AWG
12 AWG
Normal / Emergency load with UL1008BCELTS1277
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load
H
12 AWG 12 AWG
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
H
12 AWG 12 AWG
Normal
Load
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
H
12 AWG 12 AWG
Normal
Load
Red
White
Red
White
Red
White
BA
NXRC- 1R
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
4x4 JUNCTION
BOX
Black (Line 120/277 VAC)
White (Neutral)
12 AWG
N
Red
White
H
Neutral
Line 4
3
#UL924SR1
#UL924SR2
Bypass Shunt Relay
Shunt
Line
1
2
Normal/Emergency
Load
Normal /
Emergency Power
Normal Power
Black (Line 120/277 VAC)
White (Neutral)
S5. C9 Normal / Emergency load with UL924SRx
12 AWG
12 AWG
4x4 JUNCTION
BOX
Line Voltage
Receptacles
NXRC-1R
BA
CAT5/6 Cable
Normal switching load and receptacle load
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
12 AWG R
HUBBELL
Building
Automation
+
-
OCC
PC
BA
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
NXRC- 1R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
H
12 AWG 12 AWG
Normal
Load
Red
White
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG
BA
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for representation purposes.
Additional switches can be daisy chained using similar wiring
up to 'X' nos. observing power budget of controller.
Please refer to notes section in this document
NXRC- 1R
4x4 JUNCTION
BOX
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
Black (Line 120/277/347 VAC)
White (Neutral)
N
H
12 AWG 12 AWG
Normal
Load
Red
White
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
Yellow
RJ45 Adapter
Red 24VDC
CAT5/6 Cable
18 AWG
R
HUBBELL
Building
Automation
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Hot
Blue (Control)
Black (Common)
Neutral
Ground
120 VAC
18 AWG
HCSREC-F
+
-
OCC
PC
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on application and requirement.
Additional sensors can be added in the daisy chain up to 'X'
nos. observing power budget of controller.
Please refer to notes section in this document
RJ45 Adapter
RJ45 Adapter
18 AWG
Normal switching load with controlled receptacle
Normal Power
R
HUBBELL
Building
Automation
+
-
OCC
PC
BA
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 1R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load
Red
White
H
12 AWG
SVC
PWRSVC PIN
ON
OFF
12 AWG
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-1
Cap off
Cap off
NXRM-H
Photo Sensor
NXDS
Networked normal switching load
S5. C2 Occupancy sensor controlled normal switching load
ALCR1277
The Gauge number near to lead color of this
device are the gauge size of wires coming out
of the device. Please refer to specification and
install cut sheets.
UL1008BCELTS1277
The Gauge number near to lead numbers and
lead color of this device are the gauge size of
wires coming out of the device. Please refer to
specification and install cut sheets.
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
S5. C6 S5. C7 S5. C8
S5. C3 S5. C4 S5. C5
S5. C10 S5. C11
S5. C12 S5. C13
H
N
Normal
Load 1
H
N
Normal/Emergency
Load 1
Neutral
Line
Line
Neutral
12 AWG
Normal Switched
Normal Neutral
12 AWG
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
(As required)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in drawing no.
HCS - NX - S6
(As required) (As required) (As required)
(As required) (As required)
(As required) (As required)
(As required) (As required)
(As required)
(As required) (As required)
(As required)
(As required)
(As required) (As required)
(As required)
(As required)
(As required)
(As required)
(As required) (As required)
(As required) (As required)
(As required) (As required)
Ground
(As required)
CAT5/6 Cable CAT5/6 Cable
Notes
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
----Blank----
----Blank----
N
H1
V1
GViolet
Gray
Red
White
White (Neutral)
4x4 JUNCTION
BOX
White (Neutral)
Black (Line 120/277/347 VAC)
Violet/Striped Cap Off
12 AWG
Normal/Emergency
Dimming Load
12 AWG
18 AWG
Normal / Emergency Power
NXRC-UL924-UNV
Yellow
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
08/04/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
NXRC CONTROLLERS WITH SINGLE LOAD
HCS - NX - S5
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
05/20/21 AJ
B
R
HUBBELL
Building
Automation
+
-
OCC
PC
BA
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
S6. C1 Normal switching load
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
Networked normal switching load
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
S6. C2
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2R
CAT5/6 Cable
CAT5/6 Cable
18 AWG
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NXRM-H
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
SVC
PWRSVC PIN
ON
OFF
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
NXBTC
CAT5/6 Cable
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
Normal switching load with NXBTC
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Occupancy sensor controlled normal switching load
BA
NXRC- 2R
4x4 JUNCTION
BOX
4x4 JUNCTION
BOX
Blue (Test Loop)
ALCR1277
Emergency Light Controller
(Red)
Emergency Pow
Output On
Black
(Green)
Normal Power
Blue (Test Loop)
Purple (Dimmer Loop)
Purple (Dimmer Loop)
White
Red
Red
Gray
Black
CCntrl.
Normal
Load 1
H
N
Normal/Emergency
Load 1
To Optional Remote
Test Switch
Normal/Emergency Switched
Normal/Emergency (Line 120/277 VAC)
Normal/Emergency (Neutral)
Normal/Emergency Power
Neutral
Line
Line
Neutral
Line 120/270 VAC
Neutral
Normal Switched
12 AWG
Black (Line 120/277 VAC)
White (Neutral)
12 AWG
Normal Power
Black
White
Red
Red
Gray
Black
16 AWG
12 AWG
12 AWG
16 AWG
16 AWG
16 AWG
Normal Switched (Red)
Normal Neutral
12 AWG
12 AWG
ALCR1277
The Gauge number near to this device lead
colors are the gauge size of wires coming out
of the device. Please refer to specification and
install cut sheets.
Cap off
Normal
Load 2
N
H1
N
H2 Line
Neutral
12 AWG
Normal Switched (Blue)
Normal Neutral
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
Normal / Emergency load with ALCR1277
BA
NXRC- 2R
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
TEST SWITCH
EMERGENCY
POWER
UTILITY
POWER
UL924EPC1D-UNV
Emergency Light
Load Controller
1 Black (120V)
2 Orange (277V)
4 White
3 Red
6 Yellow
7 White/Blue
N
Normal/Emergency
Load 1
Line
Neutral
Normal/Emergency (Line -120/277 VAC)
Normal/Emergency Neutral
Normal/Emergency Switched
5 Blue
Select
connection
wire
based on
voltage
Black
Blue
(+0-10V In)
Red
(+0-10V Out)
Cap off
Plenum
Low
Voltage
Wiring
Line 120V/277 VAC
Neutral
Normal Switched
Normal/Emergency Power
H
12 AWG
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
12 AWG
S6. C6 Normal / Emergency load with UL924EPC1D-UNV
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Cap off
Normal
Load 1
Neutral
Line
12 AWG
Normal Switched (Red)
Normal Neutral
Normal
Load 2
N
H1
N
H2 Line
Neutral
12 AWG
Normal Switched (Blue)
Normal Neutral
12 AWG
BA
NXRC- 2R
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
#3 Blue
#12 Blue
#1 Orange
UTILITY
EMERGENCY
STATUS
TEST
SET
#4 White/Blue
#13 White/Blue
UL1008BCELTS1277
16Amps Max.
Normal/Emergency (Line 120/277VAC)
Normal/Emergency Neutral
#6 Red/White
#5 Red
#9 Yellow
Cap Off
Red Loop (20AWG) for use with a
Normally Closed Maintained
Fire Alarm Switch
#11 White
#2 White
#10 Black
#7 Purple (Out)
#8 Brown (In)
Normal/Emergency Switched
Neutral
Normal Switched
4x4 JUNCTION
BOX
Line 120/277 VAC
12 AWG
Normal/Emergency
Power
Black (Line 120/277 VAC)
White (Neutral)
Normal Power
18 AWG
12 AWG
18 AWG
12 AWG
12 AWG
12 AWG
18 AWG
16 AWG
16 AWG
12 AWG
12 AWG
18 AWG
18 AWG
12 AWG
Normal Switched
Normal Neutral
Normal/Emergency Neutral
12 AWG
12 AWG
12 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
UL1008BCELTS1277
The Gauge number near to lead numbers and
lead color of this device are the gauge size of
wires coming out of the device. Please refer to
specification and install cut sheets.
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
Normal Switched (Blue)
Normal Neutral
N
Normal/Emergency
Load 1
Line
Neutral
H
Normal
Load 1
Neutral
Line
Normal
Load 2
N
H1
N
H2 Line
Neutral
12 AWG
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
Normal / Emergency load with UL1008BCELTS1277
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
4x4 JUNCTION
BOX
Line Voltage
Receptacles
NXRC-1R
BA
CAT5/6 Cable
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
Normal switching load and receptacle load S6. C12
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
Hot
Blue (Control)
Black (Common)
Neutral
Ground
120 VAC
HCSREC-F
18 AWG
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
RJ45 Adapter
Red 24VDC
Blue
18 AWG
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
Normal switching load with controlled receptacle
CAT5/6 Cable
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
R
HUBBELL
Building
Automation
+
-
OCC
PC
Black
Yellow
Red 24VDC
18 AWG
RJ45 Adapter
CAT5/6 Cable
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
S6. C7 S6. C8
Normal / Emergency load with UL924SRx
BA
NXRC- 2R
4x4 JUNCTION
BOX
N
Red
White
12 AWG
12 AWG
H1
Neutral
Line 4
3
#UL924SR1
#UL924SR2
Bypass Shunt Relay
Shunt
Line
1
2
12 AWG
12 AWG
Normal/Emergency
Load 1
(Shunt Capable)
Black (Line 120/277 VAC)
White (Neutral)
Normal /
Emergency Power
Normal Power
Black (Line 120/277 VAC)
White (Neutral)
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for
representation purposes.
Additional switches can be daisy chained
using similar wiring up to 'X' nos.
observing power budget of controller.
Please refer to notes section in this
document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NWhite
Blue
H2
12 AWG
White (Neutral)
Normal/Emergency
Load 2
(Not Shunt)
S6. C9
S6. C11
S6. C10
Networked normal / emergency dimming load on NXRC-UL924 room controller and receptacle load
S6. C3 S6. C4
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
S6. C5 Daylight sensor controlled normal switching load
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
Photo Sensor
NXDS
(As required) (As required) (As required) (As required)
(As required)
(As required) (As required)
(As required) (As required)
(As required) (As required)
(As required)
(As required) (As required)
(As required)
(As required) (As required)
(As required)
(As required)
(As required) (As required)
(As required)
(As required) (As required)
NXCBL + CAT5/6 Cable
Refer to Detail-1
in this drawing
(HCS - NX - S6)
Details
Note:
1. To connect an NXSMP sensors or NXRM-H radio to a T568B standard CAT5/6 cable using an RJ45 connector it is necessary to use the NXCBL-P-10
plenum accessory cable to bridge the sensor to the CAT5/6 connector.
2. NXSMP sensors and NXRM-H radios have two connection terminals to achieve daisy chaining to other NXFX devices.
NXCBL-P-10
CAT5/6 Cable
NXSMP or NXRM-H
Detail-1 : NXRM-H/NXSMP to CAT5/6 cable
Notes
1. For Power budget of Room controllers and device loads, Please refer "3451B_NX_Room_Controller_Install_and_Operation.pdf".
See document link:https://hubbellcdn.com/installationmanuals/3451B_NX_Room_Controller_Install_and_Operation.pdf. (See Note 10 below)
2. For NX Smart switches (NXSW-1 upto NXSW-6 switch stations), each buttons on the station maybe programmed for different functions as desired
using NX Device Setup App. Please refer 3457.1A_NX_Smart_Switch.pdf
See document link: https://hubbellcdn.com/specsheet/3457.1A_NX_Smart_Switch.pdf
3. For NX Speciality switches (NXSW-OO/ ORLO / RL switch stations), please refer 3457.2A_NX_Specialty_Switches.pdf
See document link: https://hubbellcdn.com/specsheet/3457.2A_NX_Specialty_Switches.pdf
4. For guide on NX Switch stations, please refer HCS_NX_Switch_Guide.pdf.
See document link: https://hubbellcdn.com/literature/HCS_NX_Switch_Guide.pdf
5. For NX Occupancy sensors, please refer 3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf and
3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf.
See document link: https://hubbellcdn.com/specsheet/3459A.1_NX_Wall_Mount_Occupancy_Sensors_Specification_Sheet.pdf
See document link:: https://hubbellcdn.com/specsheet/3459A_NX_Ceiling_Mount_Occupancy_Sensors_Specification_Sheet.pdf
6. For Occupacy sensors selection guide, please refer : Sensor_Selection_Tool.pdf and for application guide, refer : HCS_Sensor_B.pdf
See document link: https://hubbellcdn.com/literature/Sensor_Selection_Tool.pdf
See document link: https://hubbellcdn.com/brochure/HCS_Sensor_B.pdf
7. For NXSMP-OMNI Indoor/Outdoor sensors, Please refer document OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
See link: https://hubbellcdn.com/specsheet/NX_OMNI_Indoor_Sensor_Module_Specification_Sheet.pdf
8. For NX Brochure, Please see link: https://hubbellcdn.com/brochure/HCS_NX_Brochure.pdf
9. For NX Design Application guide, Please see link: https://hubbellcdn.com/brochure/NX_Design_Application_Guide.pdf
10. MAXIMUM POWER BUDGET PER ROOM CONTROLLER OR IN-FIXTURE MODULE = +30 PBUs.
BA
NXRC- 2R
4x4 JUNCTION
BOX
Black (Line 120/277/347 VAC)
White (Neutral)
Normal Power
N
Normal
Load 1
Red
White
12 AWG 12 AWG
N
Normal
Load 2 Blue
White
H2
H1
Neutral
12 AWG
Red 24VDC
Black
Yellow
R
HUBBELL
Building
Automation
+
-
OCC
PC
CAT5/6 Cable
18 AWG RJ45 Adapter
CAT5/6 Cable
NX Switch Station
Typical Model :
NXSW-OO
SVC
PWRSVC PIN
ON
OFF
NX Wall Station. (NXSW)
The NXSW wall station shown is for representation purposes.
Additional switches can be daisy chained using similar wiring up
to 'X' nos. observing power budget of controller.
Please refer to notes section in this document
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
NX Switch Station
Typical Model :
NXSW-4
SVC
PWRSVC PIN
4x4 JUNCTION
BOX
Line Voltage
Receptacles NXRC-1R
BA
CAT5/6 Cable
Red
White Neutral
Switched Hot
12 AWG
Ground
Black (Line 120 VAC)
White (Neutral)
Normal Power
12 AWG
CAT5/6 Cable
Photo Sensor
NXDS
(As required) (As required)
NX Bridge Module
NXHNB2 G
V1
H1
NRed
White
Violet
Gray
18 AWG
4x4 JUNCTION
BOX
BA
Blue
Blue
Remote Test Button or
Fire Alarm interface
NXRC-UL924-UNV
Normal / Emergency Power
12 AWG
Normal/Emergency
Dimming Load
HubbNET NetworkHubbNET Network
CAT5/6 Cable
CAT5/6 Cable CAT5/6 Cable
R
HUBBELL
Building
Automation
+
-
OCC
PC
RJ45 Adapter
Red 24VDC
Blue
Black
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
Low Voltage
Occupancy Sensor
Typical Model : OMDT2
CAT5/6 Cable
18 AWG
Low Voltage Occupancy Sensor
Select model of sensor based on
application and requirement.
Additional sensors can be added in the
daisy chain up to 'X' nos. observing
power budget of controller.
Please refer to notes section in this
document
(As required)
Black (Line 120/277/347 VAC)
White (Neutral)
12 AWG
Violet/Striped
Cap Off
CAT5/6 Cable
DRAWN BY: DATE:
DRAWING / DESIGN NO.:
SCALE:REV.
TITLE:
08/04/2020SR
0NTS
701 Millennium Blvd.
Greenville, SC 29607
www.hubbellcontrolsolutions.com
NX TYPICAL CONFIGURATIONS:
NXRC CONTROLLERS WITH DUAL LOAD
HCS - NX - S6
Main Switchboard: (864) 678-1000
Technical Service: (800) 888-8006
Date By
Rev.
05/20/21 AJ
B
/