Hubbell Control Solutions NX SmartPORT Module Installation guide

Brand
Hubbell Control Solutions
Model
NX SmartPORT Module
Type
Installation guide

Hubbell Control Solutions NX SmartPORT Module

The Hubbell Control Solutions NX SmartPORT Module (NXSP) is a device that allows you to connect NX digital smart switches, occupancy sensors, and daylight sensors to the NX HubbNET™ network. This module provides the means to control lighting and other electrical devices in a building or other structure, and can be used in a variety of applications, such as:

  • Energy management: The NXSP can be used to control lighting and other electrical devices in order to reduce energy consumption. For example, the module can be used to automatically turn off lights when a room is unoccupied, or to dim lights when natural light is available.

Hubbell Control Solutions NX SmartPORT Module

The Hubbell Control Solutions NX SmartPORT Module (NXSP) is a device that allows you to connect NX digital smart switches, occupancy sensors, and daylight sensors to the NX HubbNET™ network. This module provides the means to control lighting and other electrical devices in a building or other structure, and can be used in a variety of applications, such as:

  • Energy management: The NXSP can be used to control lighting and other electrical devices in order to reduce energy consumption. For example, the module can be used to automatically turn off lights when a room is unoccupied, or to dim lights when natural light is available.
3456B 121019
72-00662
™NXSP KIT
INSTALLATION INSTRUCTIONS
INTRODUCTION
Read and understand all instructions before beginning installation.
NOTICE: For installation by a licensed electrician in accordance with National and/or local Electrical Codes and the following instructions.
Conrm device ratings are suitable for application prior to installation. Use of device in applications beyond its specied ratings or in applications other
than its intended use may cause an unsafe condition and will void manufacturer’s warranty.
Use only approved materials and components (i.e. wire nuts, electrical box, etc.) as appropriate for installation.
NOTICE: Do not install if product appears to be damaged.
SAVE THESE INSTRUCTIONS!
DESCRIPTION
The Hubbell Control Solutions’ SmartPORT™ Module (NXSP) provides the means to connect NX digital smart switches, occupancy sensors, and daylight
sensors to the NX HubbNET™ network. The NXSP requires the NXHDI Network Device Interface Module to provide the means of connection to the NX
HubbNET network.
INSTALLATION
1. Open the NXSP kit. Make sure all the necessary parts are there. It should include the following: NXHDI Module, NXSP, Power Supply, Din Rails & Screws,
Metal Enclosure and Enclosure Cover. See Figure 1, 2.
2. Screw in the Din Rail tracks inside the enclosure.
3. Snap the NXHDI onto the DIN Rail track, on the left side.
4. Snap the NXSP module onto the DIN rail track in the enclosure to the right side of the NXHDI Network Device Interface Module. See Figure 3.
5. Plug the ribbon cable supplied with the unit into the matching connector on the NXHDI module.
6. Plug the Smart Switches, occupancy sensors, or daylight sensors into one of the four RJ45 ports as needed. Note that each port has two RJ45 connectors
as a convenience. See Figure 4.
7. Follow the instructions provided with the NX Smart Switches and sensors. Refer Figure 5.
Figure 1 Figure 2 Figure 3
Figure 4
IMPORTANT: Route the HubbNET™ network so that there is no more than 100 meters (330 feet) of Cat5e wire between any two bridges or NXHDI
modules. It is strongly recommended that network segments are restricted to a single oor or wing of the building to facilitate troubleshooting.
Do not “snake” the network wire between oors. Two network segments can originate from the standard Area Controller. Consult the Hubbell Control
Solutions' factory if additional network segments are required.
701 Millennium Blvd. | Greenville, SC 29607 | (864) 678-1000 | (866) 898-0131 - fax www.hubbellcontrolsolutions.com
Copyright © 2019 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.
3456B 121019
72-00662
™NXSP KIT
INSTALLATION INSTRUCTIONS
CONNECTING DEVICES
There are four pairs of RJ45 ports on the SmartPORT™ module to which a variety of control devices can be connected and programmed to work with the
system. Application parameters vary based on the type of devices connected.
Switch Stations
Up to eight (8) switch stations total can be connected to each pair of ports. These can split between the two RJ45 connectors for each port combination.
Each switch connected to the same port (top and bottom combined) must have a unique address setting between 1 and 8. Instructions are provided with
the switch stations for setting the address.
Occupancy Sensors
Each SmartPORT module supports a maximum of four (4) zones of occupancy, one for each pair of ports. This is regardless of the number of actual
occupancy sensors connected. Multiple occupancy sensors may be connected to a port to increase the size of the area to be controlled. However, all of
the occupancy sensors connected to a port will be discovered by the Area Controller as a single sensor and they will control the same area.
Daylight Sensors
The SmartPORT module supports a maximum of four (4) daylight harvesting zones, one for each pair of ports. Connect only one daylight sensor to
each port.
Note: Switch stations, occupancy sensors, and daylight sensors can share ports as needed provided the above restrictions for each control type
are followed.
Figure 5
701 Millennium Blvd. | Greenville, SC 29607 | (864) 678-1000 | (866) 898-0131 - fax www.hubbellcontrolsolutions.com
Copyright © 2019 Hubbell Control Solutions, a division of Hubbell Lighting, Inc. All rights reserved. All product and company names, logos and product
identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any
aliation with or endorsement by such respective owners.
  • Page 1 1
  • Page 2 2

Hubbell Control Solutions NX SmartPORT Module Installation guide

Brand
Hubbell Control Solutions
Model
NX SmartPORT Module
Type
Installation guide

Hubbell Control Solutions NX SmartPORT Module

The Hubbell Control Solutions NX SmartPORT Module (NXSP) is a device that allows you to connect NX digital smart switches, occupancy sensors, and daylight sensors to the NX HubbNET™ network. This module provides the means to control lighting and other electrical devices in a building or other structure, and can be used in a variety of applications, such as:

  • Energy management: The NXSP can be used to control lighting and other electrical devices in order to reduce energy consumption. For example, the module can be used to automatically turn off lights when a room is unoccupied, or to dim lights when natural light is available.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents