MK K5437R Installation & Operating Instructions

Brand: MK

Model: K5437R

Category: Wall transmitters

Type: Installation & Operating Instructions

MK K5437R is a 1 Gang Leaded Multi-Function Switch Receiver that can be operated with Echo transmitters (radio signal). It allows for the switching of various electric loads such as lamp bulbs, HV halogen lamps, electronic ballast devices, and inductive loads. The receiver can be assigned to up to 32 transmitters, and each transmitter can control an unlimited number of receivers.

The MK K5437R offers various functions, including:

Function 1 (default): Two-button operation (switch on with button I, switch off with button O)
Function 2: One-button operation (toggle switch state with button)

The MK K5437R offers various functions, including:

Function 1 (default): Two-button operation (switch on with button I, switch off with button O)
Function 2: One-button operation (toggle switch state with button)

K5437R

1 GANG LEADED MULTI-FUNCTION SWITCH

RECEIVER

Installation & Operating Instructions

Various electric loads such as lamp bulbs, HV halogen lamps, electronic

ballast devices and inductive loads can be switched with output 1v of the

receiver. The receiver is operated with Echo transmitters (radio signal).

Before use, the transmitters must be assigned to the receiver (max. 32

receivers). Every transmitter can control an unlimited number of

receivers.

SAFETY:

CAUTION! 230V, Danger of electrical shock! Always

disconnect the electricity supply before commencing work on

the installation.

The device should be installed by a competent person or a qualified

electrician in accordance with the device’s installation instructions and

the appropriate current national wiring regulations.

It is essential that all connections are made as instructed, that cables are

not stressed and that terminals are fully tightened.

Screwless terminals must not have more than one cable inserted into

each terminal.

The mains supply to this product must be protected by an appropriate

fuse or MCB.

SPECIFICATION:

General Data

Transmit frequency 868.3MHz

Power supply 230V~ / 50Hz

Power line protection Circuit breaker rated for 16A max

Ambient temperature -20 to +40°C

Storage temperature -40 to +85°C

Test specifications EN 60669-2-1

Identification CE; KEMA/KEUR

Protection type IP20

Load Types

Incandescent lamps 2500W

HV halogen lamps 1200W

Inductive 600VA

Electronic transformer 3 units

INSTALLATION:

General Information

• NEVER install Echo receivers in a metal enclosure or in the

immediate vicinity of large metal objects.

• Installation close to floor level or on the floor is not recommended.

Installation

Important: This device should be installed into a flush mounted

installation box.

The receiver’s housing design also makes it ideally suitable for

installation in a false ceiling. This is accomplished by using the

mounting hole in the middle of the housing.

Caution! All Echo transmitters to be used should be assigned and

programmed with the desired function prior to final installation of this

receiver in a false ceiling.

• Install receiver in a suitable position.

• Protect power supply line with an automatic circuit breaker (max 16A)

• Install connection cables.

Commissioning

• Switch on power supply after installation.

• Program the receiver

RF RANGE:

The strength of the radio signal between the transmitter and switching

receiver weakens as distance increases. The range can be further

reduced by different materials or interference sources in the propagation

direction of the radio waves. The range can be increased by the use of

Echo Repeaters (radio amplifiers).

Material Reduction

Wood, plaster, non-coated glass 0 - 10%

Masonry, wood/plaster walls 5 - 35%

Reinforced concrete 10 - 90%

Range Conditions

> 30 m

Under good conditions (large, clear space without

obstructions).

> 20 m

Through up to 5 plaster/drywall board walls or 2

brick/porous concrete walls (furniture and persons in

the room):

For transmitter and receiver with good aerial

positioning/layout.

> 10 m

Through up to 5 plaster/drywall board walls or 2

brick/porous concrete walls (furniture and persons in

the room):

For receivers installed in walls or corners of rooms,

receivers with internal aerial or narrow corridors.

Through 1-2

ceilings / walls

Depending on ceiling/wall armouring and type of

aerial in the receiver.

PROGRAMMING:

For programming, the receivers must be connected to the mains power

supply. The programming is retained even in a power failure.

Learn Mode: Assigning and Deleting Transmitters

Notes:

– No transmitter is assigned to the receiver in its delivered state.

– Several transmitters can be assigned or deleted (max. 32 receivers) in

learn mode.

– A transmitter is alternately assigned (LED on) or deleted (LED off)

each time the button is pressed!

– The receiver‘s Function 1 is preset after assigning a transmitter to the

receiver. The function can be changed for every transmitter.

– If no action takes place, learn mode will be terminated after 30s

Deleting All Transmitters

Function Programming

Note: If no action takes place, function programming will be terminated

after 30 s.

Transmitter detection, (e.g. press transmitter button)

Activate transmitter once

LED blinks orange – transmitter detected

Function setting, (e.g. function 3)

LRN/SET button 3 x activated

LED blinks 3 x orange – function3

Parameter setting, (e.g. parameter 2)

LRN/SET button 2 x activated

LED blinks 2 x green – parameter 2

OPERATION AND FUNCTIONS:

The receiver is operated with Echo transmitters (radio signal). Before

use, the transmitters must be assigned to the receiver (max. 32

receivers). The receiver‘s Function 1 is preset after assigning a

transmitter to the receiver. It can be changed by function programming.

Every transmitter can control an unlimited number of receivers.

OPERATION WITH ECHO WALL TRANSMITTERS

Function 1 – Two Button Operation

Wall Transmitter Function

Press button I Switch on

Press button O Switch off

Note: Default function for a transmitter just assigned to the receiver and

also the function for motion sensors!

Function 2: One Button Operation

Wall Transmitter Function

Press button Toggle switch state

Parameters

1 Button O is activated

2 Button 1 is activated

3 Button 1 and O are activated

Function 3: Button Control

Wall Transmitter Function

Press button Switch on

Release button Switch off

Parameters

1 Button O is activated

2 Button 1 is activated

3 Button 1 and O are activated

4 Button O is activated, (pulse time 5s)

5 Button 1 is activated, (pulse time 5s)

6 Button 1 and O are activated, (pulse time 5s)

Function 4: Stairwell Light

Wall Transmitter Function

Press button I or O

Switch on with running time

(parameter)

Parameters

1 2 min running time

2 1 min running time

3 5 min running time

4 10 min running time

5 20 min running time

6 30 min running time

7 60 min running time

8 120 min running time

Note: Following the preset running time, the light will be switched off for

2s (switch-off warning) and then switched on again for another 30s

Function 5: Time Switch

Wall Transmitter Function

Press button I

Switch on with running time

(parameter)

Press button O Switch off

Parameters

1 2 min running time

2 1 min running time

3 5 min running time

4 10 min running time

5 20 min running time

6 30 min running time

7 60 min running time

8 120 min running time

Function 6: Fan Control

Wall Transmitter Function

Press button I Switch on delay (3 minutes)

Press button O Activate running time parameter

Parameters

1 6 min delay time

2 2 min delay time

3 10 min delay time

4 15 min delay time

5 20 min delay time

6 30 min delay time

Function 7 - Light Scenes

Wall Transmitter Function

Press button O briefly Switch on light scene A/C

Press button O long Store light scene A/C

Press button I briefly Switch on light scene B/D

Press button I long Store light scene B/D

Parameters

1 button O = light scene A, button I = light scene B

2 button O = light scene C, button I = light scene D

OPERATION WITH ECHO WINDOW CONTACT

Echo/Echo

Window Contact

Notes:

– The assignment and programming of a window contact is also

possible before the installation.

– Control of the receiver with window contacts and window handles

(beginning with Version 1.1).

Function 8 and 9: Switch On / Off

Window Contact Function 8 Function 9

Window contact opened Switch on Switch off

All window contacts closed Switch off Switch on

Parameters

1 Window contact function

2 Window handle function

TROUBLESHOOTING:

New system or existing system

• Check power supply (electrician only).

• Check connected electrical loads.

• Check the system’s surroundings for changes that could cause interference

(e.g. metal cabinets, furniture or walls which have been moved).

• If the transmitter/receiver operates at a reduced distance, the radio signal was

encountering interference or it was operating outside the transmission range.

• Use the receiver at a better location.

• Delete all transmitters and reprogram the receiver.

Receiver switches by itself

• This may be caused by operation of an external transmitter that was

coincidentally assigned to the receiver.

• Delete all transmitters and reprogram the receiver.

Radio signal range limitations

• Use of the receiver in the vicinity of metal objects or materials with metal

components. Maintain a distance of at least 10cm

• Moist materials.

• Devices which emit high-frequency signals (e.g. audio and video systems,

computers, electronic ballasts in light fixtures). Maintain a distance of at least

0.5m

OTHER INFORMATION:

Disposal:

At the end of their useful life the packaging and product should

be disposed of via a suitable recycling centre. Do not dispose

of with your normal household waste. Do not burn.

EU R&TTE Declaration:

Novar ED&S Ltd hereby declares that the K5437 Switch Receiver is in

compliance with the essential requirements and other relevant

provisions of the European Radio and Telecommunications

Terminal Equipment (R&TTE) directive, 1999/5/EC.

A copy of the Declaration of Conformity for this product may be found at:

www.electrical.honeywell.com

Guarantee:

MK Electric undertakes to replace or repair at its discretion goods should

they become defective within 10 years solely as a result of faulty

materials and workmanship. Understandably if the product has not been

installed, operated or maintained in accordance with the instructions,

has not been used appropriately or if any attempt has been made to

rectify, dismantle or alter the product in any way the guarantee will be

invalidated.

The guarantee states MK Electric’s entire liability. It does not extend to

cover consequential loss or damage or installation costs arising from the

defective product. This guarantee does not restrict, infringe or in any

way affect the normal statutory or other rights of the consumer.

For help and advice please contact the technical service helpline: 01268 563720

Email: mk.technical@honeywell.com

MK Electric Telephone: +44 (0)1268 563000

The Arnold Centre, Paycocke Rd, , Fax: +44 (0)1268 563404

Basildon Essex SS14 3EA UK Email: mk.orderenquiries@honeywell.com

MK Electric (Middle East) Telephone: (+971) 4 807 3200

Honeywell ME, FZE, P.O. Box 18530, Fax: (+971) 4 881 5733

Jebel All, Dubai U.A.E.

www.electrical.honeywell.com

Novar ED&S Ltd, (A Honeywell Company)

Arlington Business Park, Bracknell,

Berkshire, RG12 1EB, UK

50064828-001_A

MK K5437R Installation & Operating Instructions

Brand: MK

Model: K5437R

Category: Wall transmitters

Type: Installation & Operating Instructions

The MK K5437R offers various functions, including:

Function 1 (default): Two-button operation (switch on with button I, switch off with button O)
Function 2: One-button operation (toggle switch state with button)

Download PDF

report

MK K5437R Installation & Operating Instructions

MK K5437R Installation & Operating Instructions

Related papers

Other documents