Sauder 423450 Operating instructions

Type
Operating instructions
sauder.com
Queen Platform Bed
Model 423450
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-30
Français p 31-34
Español p 35-38
Lot # 532896 08/27/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a rin at
1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
You won't just fall in
love with it. You'll fall
asleep in it.
Table of Contents Assembly Tools Required
2-3
4
5-30
31-34
35-38
39
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
423450 www.sauder.com/servicePae 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identifi cation to help identify similar parts.
A HEADBOARD (1)
B SIDE PANEL (4)
B49 DRAWER BOTTOM (2)
C HEADBOARD LEFT LEG (1)
D HEADBOARD RIGHT LEG (1)
D270 DRAWER SIDE (4)
D528 DRAWER BOX FRONT (2)
D530 DRAWER BOX FRONT (2)
E CENTER LEG (2)
F FOOTBOARD LEFT LEG (1)
G FOOTBOARD RIGHT LEG (1)
H UPPER SIDE RAIL (4)
J LOWER SIDE RAIL (4)
K CENTER SUPPORT (1)
L SHORT CLEAT (2)
M CLEAT (5)
N TOP LEFT MOLDING (2)
O TOP RIGHT MOLDING (2)
P FOOTBOARD TOP MOLDING (1)
Q UPRIGHT (1)
R PLATFORM (5)
S PLATFORM SUPPORT (5)
T FOOTBOARD LOWER RAIL (1)
U FOOTBOARD UPPER RAIL (1)
V DRAWER FRONT (2)
W
DRAWER BRACE (2)
(Hidden part usin recycled
material. Color may vary.)
Now you know
our ABCs.
Tape Measure
Part Identifi cation
423450www.sauder.com/service
Pae 3
D270
B49
A
B
C
D
E
F
G
H
J
K
L
M
O
N
P
Q
R
S
T
U
V
W
B
E
H
L
M
S
S
S
S
D270
D528
D530
B
J
O
H
M
J
H
M
N
B
J
M
D270
B49
V
W
D270
D530
D528
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
423450 www.sauder.com/servicePae 4
40DA
UNIVERSAL
CABINET RAIL - 4
40DC
DRAWER
RIGHT - 2
40DD
DRAWER
LEFT - 2
PULL - 2
149K
HIDDEN CAM - 42
1F
CAM SCREW - 42
8F
HIDDEN
CONNECTOR - 16
9F
WOOD DOWEL - 18
15F
GLUE - 1
54M
CONNECTOR SCREW - 16
8S
BLACK 1-1/8" PAN HEAD SCREW - 31
9S
12S
BROWN 1" FLAT HEAD SCREW - 24
BLACK 7/8" LARGE HEAD SCREW - 4
17S
SILVER 3/4" MACHINE SCREW - 4
20S
30S
BLACK 1-9/16" FLAT HEAD SCREW - 20
BLACK 1-1/2" FLAT HEAD SCREW - 16
101S
BLACK 1-15/16" FLAT HEAD SCREW - 12
113S
TACK GLIDE - 12
13E
3S
GOLD 5/16" FLAT HEAD SCREW - 16
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
423450www.sauder.com/service
Pae 5
å
Assemble your unit on a carpeted fl oor or on the empty carton to avoid
scratchin your unit or the fl oor.
å
Insert a CONNECTOR SCREW (8S) into each HIDDEN CONNECTOR (9F).
å
Use your hammer to tap sixteen HIDDEN
CONNECTORS (9F) with SCREWS into the SIDE
PANELS (B) and FOOTBOARD UPPER RAIL (U).
Step 2
9F
8S
8S
B
U
9F
(16 used)
B
B
B
Step 3
å
Push forty-two HIDDEN CAMS (1F) into the HEADBOARD (A),
SIDE PANELS (B), CENTER SUPPORT (K), UPRIGHT (Q), and
FOOTBOARD RAILS (T and U).
423450 www.sauder.com/servicePae 6
B
U
B
B
B
Q
A
K
T
1F
Arrow
(42 used)
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
å
Turn forty-two CAM SCREWS (8F) into the LEGS (C, D, E, F,
and G) and FOOTBOARD RAILS (T and U).
å
NOTE: Use the exact holes shown.
Step 4
423450www.sauder.com/service
Pae 7
U
T
C
D
E
E
F
G
8F
(42 used)
8F
8F
Step 5
å
Fasten one UNIVERSAL CABINET RAIL* (40DA) to each
side of the UPRIGHT (Q). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S) throuh holes #1 and #4.
å
*patent pendin lide system
423450 www.sauder.com/servicePae 8
Q
VIEW THE DRAWER GLIDE VIDEO
1
2
3
4
1
2
3
4
Finished ede
Glide end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
å
Fasten the FOOTBOARD TOP MOLDING (P) to
the FOOTBOARD UPPER RAIL (U). Tihten four
HIDDEN CONNECTORS.
Step 6
423450www.sauder.com/service
Pae 9
Surface with HIDDEN
CONNECTORS
U
P
How to use the HIDDEN CONNECTOR
To fasten two parts toether usin the HIDDEN
CONNECTORS, insert your screwdriver, at an anle,
into the slot in the HIDDEN CONNECTOR. While
pushin the screw into the hole of the adjoinin
part, turn the screwdriver clockwise to tihten.
Surface with holes
The holes in the
MOLDING are closer
to the top ede.
Step 7
å
Fasten the TOP MOLDINGS (N and O) to the SIDE
PANELS (B). Tihten twelve HIDDEN CONNECTORS.
423450 www.sauder.com/servicePae 10
B
N
B
N
B
O
B
O
This end
has a hole.
This end
has a hole.
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
The holes in the
MOLDING are closer
to the top ede.
å
Fasten the LOWER SIDE RAILS (J) to the SIDE PANELS (B).
Use twelve BROWN 1" FLAT HEAD SCREWS (12S).
å
NOTE: Do not overtihten the SCREWS.
Step 8
423450www.sauder.com/service
Pae 11
B
J
B
J
B
J
B
J
BROWN 1" FLAT HEAD SCREW
(12 used in this step)
12S
Surface with holes
Surface with holes
Surface with holes
Surface with holes
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
Surface with
HIDDEN
CONNECTORS
Step 9
å
NOTE: The WOOD DOWELS (15F) will be inserted into the
ede with two CAM SCREWS in each CENTER LEG (E).
å
First, fi ll the holes in the CENTER LEGS (E) 1/4 to 1/2 full with
GLUE (54M). Then, insert the WOOD DOWELS (15F) into the
holes. Wipe away the excess GLUE.
å
Now, fi ll the holes in the CENTER SUPPORT (K) 1/4 to 1/2 full
with GLUE.
å
Fasten the CENTER LEGS (E) to the CENTER SUPPORT (K).
Tihten four HIDDEN CAMS. Wipe away the excess GLUE.
å
NOTE: Be sure the WOOD DOWELS in the CENTER LEGS
insert into the CENTER SUPPORT.
423450 www.sauder.com/servicePae 12
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thorouhly before
assemblin. Disassembly of lued
parts is extremely di cult.
Caution
!
54M
15F
15F
1
2
These surfaces
should be even.
Surface with
HIDDEN CAMS
E
K
E
These surfaces
should be even.
This hole is closer
to this ede.
Step 10
423450www.sauder.com/service
Pae 13
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thorouhly before
assemblin. Disassembly of lued
parts is extremely di cult.
Caution
!
å
NOTE: The WOOD DOWELS (15F) will be inserted into the ede
with two CAM SCREWS in each HEADBOARD LEG (C and D).
å
First, fi ll the holes in the HEADBOARD LEGS (C and D) 1/4 to 1/2
full with GLUE (54M). Then, insert the WOOD DOWELS (15F) into
the holes. Wipe away the excess GLUE.
å
Now, fi ll the holes in the HEADBOARD (A) 1/4 to 1/2 full with GLUE.
å
Fasten the HEADBOARD LEGS (C and D) to the HEADBOARD (A).
Tihten four HIDDEN CAMS. Wipe away the excess GLUE.
å
NOTE: Be sure the WOOD DOWELS in the HEADBOARD LEGS
insert into the HEADBOARD.
Surface with
HIDDEN CAMS
D
A
C
15F
54M
15F
These surfaces
should be even.
These surfaces
should be even.
These holes are
closer to this ede.
Step 11
423450 www.sauder.com/servicePae 14
å
NOTE: The WOOD DOWELS (15F) will be inserted into the ede
with two holes in each FOOTBOARD LEG (F and G).
å
First, fi ll the holes in the FOOTBOARD LEGS (F and G) 1/4 to 1/2
full with GLUE (54M). Then, insert the WOOD DOWELS (15F)
into the holes. Wipe away the excess GLUE.
å
Now, fi ll the holes in the FOOTBOARD RAILS (T and U) 1/4 to
1/2 full with GLUE.
å
Fasten the FOOTBOARD LEGS (F and G) to the FOOTBOARD
RAILS (T and U). Tihten six HIDDEN CAMS. Wipe away the
excess GLUE.
å
NOTE: Be sure the WOOD DOWELS in the FOOTBOARD LEGS
insert into the FOOTBOARD RAILS.
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thorouhly before
assemblin. Disassembly of lued
parts is extremely di cult.
Caution
!
54M
15F
15F
Surface with
HIDDEN CAMS
U
P
Surface with HIDDEN CAMS
T
G
F
These surfaces
should be even.
These surfaces
should be even.
Finished ede
å
With a hammer, tap six TACK GLIDES (13E) into the edes
of the HEADBOARD (A), CENTER SUPPORT (K), and
FOOTBOARD LOWER RAIL (T).
å
With a hammer, tap six TACK GLIDES (13E) into the
centers of the LEGS (C, D, E, F, and G).
Step 12
423450www.sauder.com/service
Pae 15
T
G
F
E
K
E
C
A
D
13E
13E
13E
Step 13
å
Fasten the UPRIGHT (Q) to the FOOTBOARD
RAILS (T and U). Tihten four HIDDEN CAMS.
423450 www.sauder.com/servicePae 16
U
T
Q
Surface with
HIDDEN CAMS
Step 14
423450www.sauder.com/service
Pae 17
U
T
B
B
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
å
NOTE: The remainin WOOD DOWELS will not be lued. If you
need to relocate your bed, disassembly and reassembly will be
easier without lue.
å
Insert two WOOD DOWELS (15F) into the holes in the
FOOTBOARD LEGS (F and G).
å
Fasten two di erent SIDE PANELS (B) to the FOOTBOARD LEGS (F
and G). Tihten six HIDDEN CAMS.
å
NOTE: One SIDE PANEL (B) will have a TOP LEFT MOLDING (N),
and the other will have a TOP RIGHT MOLDING (O).
å
NOTE: Be sure the WOOD DOWELS in the FOOTBOARD LEGS
insert into the SIDE PANELS.
å
Insert two WOOD DOWELS (15F) into the holes in the ends of the
TOP MOLDINGS (N and O).
O
N
F
G
15F
15F
15F
15F
For support, place packin
foam and maazines here.
For support, place packin
foam and maazines here.
Do not use lue
for the remainin
WOOD DOWELS.
Step 15
å
Insert two WOOD DOWELS (15F) into the holes in the
CENTER LEGS (E).
å
Fasten the CENTER LEGS (E) to the SIDE PANELS (B).
Tihten six HIDDEN CAMS.
å
NOTE: Be sure the WOOD DOWELS in the CENTER LEGS
insert into the SIDE PANELS.
å
Fasten the CENTER SUPPORT (K) to the UPRIGHT (Q).
Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
423450 www.sauder.com/servicePae 18
B
B
15F
15F
Surface with
HIDDEN CAMS
K
Q
E
E
BLACK 1-15/16" FLAT HEAD SCREW
(2 used for the UPRIGHT)
113S
å
Insert two WOOD DOWELS (15F) into the holes in the
CENTER LEGS (E).
å
Fasten the remainin SIDE PANELS (B) to the CENTER
LEGS (E). Tihten six HIDDEN CAMS.
å
NOTE: Be sure the WOOD DOWELS in the CENTER LEGS
and TOP MOLDINGS insert into the remainin SIDE
PANELS and TOP MOLDINGS.
Step 16
423450www.sauder.com/service
Pae 19
O
N
O
N
B
B
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
For support, place packin
foam and maazines here.
For support, place packin
foam and maazines here.
15F
15F
E
E
Step 17
å
Insert two WOOD DOWELS (15F) into the holes in the
HEADBOARD LEGS (C and D).
å
Fasten the HEADBOARD LEGS (C and D) to the SIDE
PANELS (B). Tihten six HIDDEN CAMS.
å
NOTE: Be sure the WOOD DOWELS in the HEADBOARD
LEGS insert into the SIDE PANELS.
423450 www.sauder.com/servicePae 20
C
A
D
Surface without
HIDDEN CAMS
B
B
15F
15F
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Sauder 423450 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI