Teknik 5425092 is a spacious L-shaped desk that provides ample workspace for your computer, paperwork, and office supplies. The desk features a large top surface, a smaller top surface, a fixed shelf, a skirt, a drawer, a modesty panel, and a back panel. The drawer is equipped with extension slides for smooth opening and closing, and it has a metal plate and tie plate for added stability. The desk also includes a pull for easy opening of the drawer, and file bars for hanging letter files. The desk is made of durable materials and is easy to assemble.
Essentials L-Shaped Desk
Model 5425092
For all your
newfangled gadgetry.
Teknik
www.teknikoffice.co.uk
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Table of Contents Assembly Tools Required
3
4
5-26
27-31
32-36
37-38
39
Page 2
Part Identifi cation
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.
Now you know
our ABCs.
A LARGE TOP (1)
B SMALL TOP (1)
C LEFT END (1)
D LEFT UPRIGHT (1)
E RIGHT UPRIGHT (1)
F RIGHT END (1)
G MOLDING (1)
H SMALL MODESTY PANEL (1)
J FIXED SHELF (2)
K SKIRT (1)
L DRAWER FRONT (1)
M LEFT DRAWER SIDE (1)
N RIGHT DRAWER SIDE (1)
O DRAWER BACK (1)
P DRAWER BOTTOM (1)
Q BACK (1)
R LARGE MODESTY PANEL (1)
A
B
C
D
E
F
G
H
J
J
KL
M
N
O
P
Q
R
Page 3
Hardware Identifi cation
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 12
5
LARGE HIDDEN
CAM - 8
3SMALL HIDDEN
CAM - 4
4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION SLIDE - 2
2
EXTENSION RAIL - 2
1
WOOD DOWEL - 30
6PULL - 1
7
APPLIQUE CARD - 2
8NAIL - 18
9
GOLD 1-3/4" FLAT HEAD SCREW - 18
14 GOLD 1-1/4" FLAT HEAD SCREW - 4
15
SILVER 15/16" PAN HEAD SCREW - 2
16 GOLD 1/2" FLAT HEAD SCREW - 22
17
METAL PLATE - 1
10
TIE PLATE - 1
11 BRACKET - 4
12 FILE BAR - 2
13
Page 4 www.sauder.com/service 425092
Step 1
Page 5
å Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratching your unit or the fl oor.
å Separate the EXTENSION SLIDES (2) from the
EXTENSION RAILS (1) as shown in diagram 1. Be
prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (1) to the LEFT END (C),
and LEFT UPRIGHT (D). Use eight GOLD 1/2" FLAT HEAD
SCREWS (17) through the holes shown in diagram 2.
å NOTE: The EXTENSION SLIDES will be used later for
the DRAWERS.
C
D
Open end
Open end
Push the black lever up and pull the SLIDE from the RAIL.
Open end
1
1
2
1
2
1
GOLD 1/2" FLAT HEAD SCREW
(8 used in this step)
17
1
Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6
Step 2
å Push four LARGE HIDDEN CAMS (3) into the large holes
in the LEFT END (C) and LEFT UPRIGHT (D).
3
C
D
3
Page 7
å Insert twelve WOOD DOWELS (6) into the
FIXED SHELVES (J) and SKIRT (K).
Step 3
J
J
K
6
(12 used)
Page 8
Just think. The sooner
you do this, the sooner
you do something else.
å Fasten the FIXED SHELVES (J) and SKIRT (K) to the
LEFT UPRIGHT (D). Use four GOLD 1-3/4" FLAT
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the SHELVES and
SKIRT insert into the UPRIGHT.
Step 4
D
J
J
K
Open end
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
Page 9
å Fasten the LEFT END (C) to the FIXED SHELVES (J)
and SKIRT (K). Use four GOLD 1-3/4" FLAT
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the SHELVES and
SKIRT insert into the UPRIGHT.
Step 5
J
J
K
C
Open end
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
Page 10 www.sauder.com/service 425092
å Push four LARGE HIDDEN CAMS (3) into the large holes
in the RIGHT UPRIGHT (E) and RIGHT END (F).
Step 6
E
F
3
(4 used)
Page 11
3
å Insert four WOOD DOWELS (6) into the SMALL MODESTY PANEL (H).
å Fasten the SMALL MODESTY PANEL (H) to the LEFT UPRIGHT (D). Use two GOLD 1- 3/4" FLAT
HEAD SCREWS (14).
å Fasten the RIGHT UPRIGHT (E) to the SMALL MODESTY PANEL (H). Use two GOLD 1- 3/4" FLAT
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL insert into the UPRIGHTS.
Step 7
E
H
D
H
6
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
Page 12
(4 used)
Step
å Insert four WOOD DOWELS (6) into the LARGE MODESTY PANEL (R).
å Fasten the LARGE MODESTY PANEL (R) to the MOLDING (G). Use
two GOLD 1- 3/4" FLAT HEAD SCREWS (14).
å Fasten the RIGHT END (F) to the LARGE MODESTY PANEL (R). Use
two GOLD 1- 3/4" FLAT HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the MODESTY PANEL insert
into the END and MOLDING..
Step 8
R
F
R
G
GOLD 1- 3/4" FLAT HEAD SCREW
(4 used in this step)
14
6
(4 used)
Edge with holes
Page 13
å Carefully stand your two assemblies upright.
å Insert two WOOD DOWELS (6) into the MOLDING (G).
å Fasten the RIGHT UPRIGHT (E) to the MOLDING (G). Use two GOLD 1-3/4" FLAT HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the MOLDING insert into the RIGHT UPRIGHT.
å Insert eight WOOD DOWELS (6) into the ENDS (C and F) and UPRIGHTS (D and E).
Step 9
6
E
G
(10 used)
D
C
6
F
GOLD 1- 3/4" FLAT HEAD SCREW
(2 used in this step)
14
Page 14
6
å Turn six CAM SCREWS (5) into the LARGE TOP (A).
å Fasten the METAL PLATE (10) and TIE PLATE (11)
to the TOP (A). Use four GOLD 1/2" FLAT HEAD SCREWS (17).
Step 10
A
5
10
11
GOLD 1/2" FLAT HEAD SCREW
(4 used in this step)
17
GOLD 1/2" FLAT HEAD SCREW
17
Page 15
Step
å Fasten the TOP (A) to the LEFT END (C) and
UPRIGHTS (D and E). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the END and
UPRIGHTS insert into the TOP.
Step 11
A
E
D
C
Page 16
å Turn two CAM SCREWS (5) into the SMALL TOP (B).
Step 12
B
5
Page 17
å Fasten the SMALL TOP (B) to the RIGHT END (F).
Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the END insert
into the TOP.
å Fasten the SMALL TOP (B) to the LARGE TOP (A). Use four
GOLD 1/2" FLAT HEAD SCREWS (17) through the METAL
PLATES, TIE PLATES, and into the SMALL TOP.
Step 13
B
F
A
GOLD 1/2" FLAT HEAD SCREW
(4 used in this step)
17
Page 18
Now might be a
good time to refresh
your drink.
å Push four SMALL HIDDEN CAMS (4) into the large holes
in the DRAWER SIDES (M and N).
Step 14
N
M
4
Page 19
4
å Fasten the EXTENSION SLIDES (2) to the
DRAWER SIDES (M and N). Use six GOLD 1/2" FLAT
HEAD SCREWS (17) through the holes shown in the
enlarged diagram.
Step 15
2
N
M
Open end
Open end
Open end
GOLD 1/2" FLAT HEAD SCREW
(6 used in this step)
17
Page 20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Sauder Costa L-Desk 419956 Assembly Manual