Sauder 410627 Operating instructions

Sauder
Brand
Sauder
Model
410627
Type
Operating instructions
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
Lot # 357576 11/19/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Corner TV Stand
August Hill Collection | Model 410627
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Your center of
attention.
Table of Contents Assembly Tools Required
3
4
5-18
19-21
22-24
25-26
27
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fi t within the space defi ned in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
95 lbs.
95 lbs.
17-1/2"
17-1/2"
39-1/4"
39-1/4"
410627 www.sauder.com/servicesPage 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.
A END (2)
B UPRIGHT (1)
C LOWER UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F SHELF (1)
G BACK (1)
H DOOR (2)
I RIGHT FRONT/LEFT REAR LEG (2)
J LEFT FRONT/RIGHT REAR LEG (2)
K EXTENSION BLOCK (2)
L STOP MOLDING (1)
M TOP MOLDING (1)
N BASE (1)
O TOP RAIL (2)
P BOTTOM RAIL (2)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
A
O
P
H
K
J
I
410627www.sauder.com/services
Page 3
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 30
Q2
CAM DOWEL - 22
R2
CAM SCREW - 8
S2
V
HINGE - 4
WASHER - 2
W
PULL - 2
X
Y
BUMPER CARD - 2
(Refer to the last step for proper
location and application)
WARNING LABEL - 1
BB
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur. The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
FOOT BASE - 1
U
FOOT - 1
T
HOLE PLUG - 2
AA
BLACK 1-7/8" FLAT HEAD SCREW - 4
DD
BROWN 1-1/2" FLAT HEAD SCREW - 3
EE
BLACK 9/16" FLAT HEAD SCREW - 8
FF
BLACK 9/16" PAN HEAD SCREW - 4
GG
BLACK 1/2" FLAT HEAD SCREW - 8
HH
BROWN 7/16" LARGE HEAD SCREW - 8
II
NAIL - 33
KK
BLACK 2-1/2" LARGE HEAD SCREW - 4
CC
SILVER 1/4" MACHINE SCREW - 2
JJ
410627 www.sauder.com/servicesPage 4
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratching your unit or the fl oor.
å
Push thirty HIDDEN CAMS (Q2) into the ENDS (A),
UPRIGHTS (B and C), TOP (D), BOTTOM (E), SHELF (F),
and one set of LEGS (I and J). Then, insert twenty-two
CAM DOWELS (R2) into the HIDDEN CAMS.
410627www.sauder.com/services
Page 5
A
B
C
D
E
F
I
J
A
Arrow
Q2
R2
Q2
Arrow
Do not tighten the HIDDEN CAMS in this step.
(22 used)
(30 used)
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
Do not insert CAM DOWELS into
the long edges of the ENDS (A).
Q2
Insert a HIDDEN CAM
and CAM DOWEL into
one LEG (I and J).
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1551
to watch a video on how to assemble your unit.
Step 2
å
Turn eight CAM SCREWS (S2) into the LEGS (I and J).
å
Fasten the LEGS (I and J) to the ENDS (A). Tighten four
HIDDEN CAMS.
410627 www.sauder.com/servicesPage 6
S2
A
I
J
A
I
J
I
J
12
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Angled edge
LEG with HIDDEN CAM
LEG with HIDDEN CAM
Angled edge
å
Carefully turn the ENDS (A) over.
å
Turn eight BLACK 9/16” FLAT HEAD SCREWS (FF) into the
ENDS (A) until the shoulder of the SCREWS rest on the surface
of the ENDS.
å
Slide the RAILS (O and P) onto the ENDS (A). Line up the
groove in the RAILS over the head of the SCREWS in the ENDS.
Step 3
410627www.sauder.com/services
Page 7
A
A
Shoulder
Apply pressure with your hands
as you guide the MOLDINGS over
the SCREWS and onto the ENDS.
BLACK 9/16" FLAT HEAD SCREW
(8 used in this step)
FF
O
O
P
P
Shoulder
Step 4
å
Carefully turn the ENDS (A) over.
å
Fasten the other LEGS (I and J) to the ENDS (A). Tighten four
HIDDEN CAMS.
å
Insert two HOLE PLUGS (AA) into the holes in the LEGS (I and J).
410627 www.sauder.com/servicesPage 8
12
A
I
J
A
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
AA
Angled edge
This END will now be
called the LEFT END.
This END will now be
called the RIGHT END.
Angled edge
å
Fasten the STOP MOLDING (L) to the TOP (D). Tighten
four HIDDEN CAMS.
Step 5
410627www.sauder.com/services
Page 9
L
D
Unfi nished surface
Rounded edge
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Surface with
HIDDEN CAMS
Step 6
å
Fasten the LEFT END (A), UPRIGHT (B), and LEFT
FRONT/RIGHT REAR LEG (J) to the TOP (D) and STOP
MOLDING (L). Tighten fi ve HIDDEN CAMS.
410627 www.sauder.com/servicesPage 10
A
J
B
D
L
Arrow
Minimum
190 degrees
Maximum
210 degrees
Surface
with
HIDDEN
CAMS
Surface without
HIDDEN CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Finished edge
å
Fasten the SHELF (F) to the LEFT END (A). Tighten two
HIDDEN CAMS.
å
Fasten the SHELF (F) to the UPRIGHT (B). Use two
BLACK 1-7/8" FLAT HEAD SCREWS (DD).
å
Fasten the LOWER UPRIGHT (C) to the SHELF (F).
Tighten two HIDDEN CAMS.
Step 7
410627www.sauder.com/services
Page 11
A
Arrow
Minimum
190 degrees
Maximum
210 degrees
C
F
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
B
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
DD
Step 8
å
Fasten the BOTTOM (E) to the LEFT END (A). Tighten two
HIDDEN CAMS.
å
Fasten the BOTTOM (E) to the LOWER UPRIGHT (C). Use two
BLACK 1-7/8" FLAT HEAD SCREWS (DD).
å
Slide the BASE (N) onto the notched edge of the BOTTOM (E).
å
*U.S. Patent No. 5,499,886
410627 www.sauder.com/servicesPage 12
Slide the BASE (N)
onto the notched edge.
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
DD
Notched edge
Arrow
Minimum
190 degrees
Maximum
210 degrees
A
C
E
N
Surface with
HIDDEN CAMS
å
Fasten the RIGHT END (A) and RIGHT FRONT/LEFT REAR
LEG (I) to the TOP (D), BOTTOM (E), SHELF (F) and STOP
MOLDING (L). Tighten seven HIDDEN CAMS.
å
Fasten the TOP MOLDING (M) to the STOP MOLDING (L).
Use three BROWN 1-1/2" FLAT HEAD SCREWS (EE).
å
Fasten the EXTENSION BLOCKS (K) to the BOTTOM (E).
Use four BLACK 2-1/2" LARGE HEAD SCREWS (CC).
Step 9
410627www.sauder.com/services
Page 13
Arrow
Minimum
190 degrees
Maximum
210 degrees
D
E
F
K
L
M
A
K
I
Surface
without
HIDDEN
CAMS
BLACK 2-1/2" LARGE HEAD SCREW
(4 used for the EXTENSION BLOCKS)
CC
BROWN 1-1/2" FLAT HEAD SCREW
(3 used for the TOP MOLDING)
EE
Step 10
å
Carefully turn your unit over onto its front edges. Unfold the BACK (G) and lay it over your unit.
å
Fasten the BACK (G) to the LEGS (I and J). Use eight BROWN 7/16" LARGE HEAD SCREWS (II). Fasten the
remaining BACK (G) to your unit using the NAILS (KK).
å
NOTE: Be sure to tap NAILS into the holes that line up over the SHELF (F).
å
NOTE: Perforations have been provided for access through the BACK. Carefully cut out the holes needed.
å
Fasten the FOOT BASE (U) to the EXTENSION BLOCK (K). Use four BLACK 9/16” PAN HEAD SCREWS (GG).
Then, push the FOOT (T) into the FOOT BASE (U).
å
NOTE: Turn the adjustable end of the ADJUSTABLE FOOT completely in. Final adjustments will be made after
the unit is standing upright.
410627 www.sauder.com/servicesPage 14
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
These holes must line
up over the SHELF (F).
NAIL
(33 used in this step)
KK
G
K
T
U
BLACK 9/16" PAN HEAD SCREW
(4 used for the FOOT BASE)
GG
BROWN 7/16" LARGE HEAD SCREW
(8 used in this step)
II
I
J
Turn completely in.
å
Fasten the HINGES (V) to the DOORS (H). Use eight
BLACK 1/2" FLAT HEAD SCREWS (HH).
Step 11
410627www.sauder.com/services
Page 15
H
V
V
H
BLACK 1/2” FLAT HEAD SCREW
(8 used in this step)
HH
Step 12
å
Carefully stand your unit upright.
å
Position your unit in its fi nal location. Turn the ADJUSTABLE FOOT (T) downward until it touches the fl oor.
å
IMPORTANT: The ADJUSTABLE FOOT should not extend beyond the bottom edges of the LEGS (I and J).
å
Fasten one of the DOORS (H) to the left END (A). Use the screws in the HINGES.
å
NOTE: You may need to loosen the mounting screw to slide it part way out of the slot. Retighten the screw before you
mount the HINGE to the END.
å
Fasten a PULL (X) to the DOOR (H). Use a WASHER (W) and a SILVER 1/4" MACHINE SCREW (JJ).
å
Peel a BUMPER from the BUMPER CARD (Y) and stick it on the DOOR where it comes in contact with the LOWER
UPRIGHT (C).
å
Repeat this step for the other door.
410627 www.sauder.com/servicesPage 16
W
A
H
C
X
SILVER 1/4" MACHINE SCREW
(2 used in this step)
JJ
Mounting screw
Turn the ADJUSTABLE FOOT
downward until it touches the fl oor.
T
Floor
Y
I
J
J
å
Refer to the enlarged diagram to identify the parts on the HINGES.
å
The DOORS may need some adjustments. Follow the text below to make needed adjustments.
å
DOOR ADJUSTMENTS:
å
To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out.
å
To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS
up or down to the desired location. Tighten the screws after making adjustments.
å
To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or
out, as needed. Tighten the mounting screw after making adjustments.
Step 13
410627www.sauder.com/services
Page 17
Adjusting screw (horizontal)
Mounting screw (depth)
(vertical adjustment)
Step 14
å
Apply the WARNING LABEL (BB) to the TOP (D). You should be able to read the label when the TV is removed from the
unit. When the TV is in place, it should hide the label. Peel o the backing and apply the label as shown in the diagram.
å
NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it.
å
NOTE: Please read the back pages of the instruction booklet for important safety information.
å
This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
410627 www.sauder.com/servicesPage 18
And to celebrate, why not share your success story?
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death can
occur. The TV and furniture will be unstable
and may tip.
- The TV must weigh less than 95 lbs.
- The base of the TV must be able to sit
completely on this shelf.
BB
95 lbs.
D
25 lbs.
25 lbs.
40 lbs. total
A l’usage exclusif du
Canada Noter la date
d’achat de cet élément
et conserver le livret
pour future référence.
Pour contacter Sauder
en ce qui concerne cet
élément, faire référence
au numéro de lot et
numéro de modèle en
appelant notre numéro
sans frais.
Lot nº : ____________
Date de
l’achat: ____________
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
NOUS SOMMES LA POUR VOUS AIDER!
Nous faisons de notre mieux pour nous assurer que votre meuble
arrive dans d’excellentes conditions. Nos représentants du service
Clientèle sont aimables et prêts à vous aider au cas où une pièce
aurait été endommagée ou manquerait (ou si vous aviez besoin
d’aide pour l’assemblage). NE RAMENEZ PAS LE MEUBLE AU
MAGASIN. Au Canada, composez ce numéro d’appel gratuit:
1-800-523-3987
Du lundi au vendredi, de 9 heures du matin à
5:30 heures du soir (horaire Côte Est)
(sauf jours fériés)
Si une pièce a besoin d’être remplacée, la pièce de remplacement
sera envoyée dans les 48 heures. (Sauf week-ends et jours fériés)
Utilisez les instructions d’assemblage en français avec les
schémas étape par étape du manuel d’instruction en anglais.
Chaque étape en français correspond à la même étape
en anglais. La pièce devant être attachée à l’élément est
représentée en gris sur les schémas de chaque étape pour plus
de précision. Comparer la “Liste de pièces” ci-dessous avec
la “PART IDENTIFICATION” du manuel en anglais pour vous
familiariser avec les pièces avant l’assemblage.
REMARQUE : CE MANUEL D’INSTRUCTIONS CONTIENT
D’IMPORTANTES INFORMATIONS RELATIVES À LA SÉCURITÉ.
À LIRE ET CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
Meuble Télévision/
Vidéo/Stéréo d'angle
Modèle 410627
Q2
EXCENTRIQUE ESCAMOTABLE
................................ 30
R2 CHEVILLE D’EXCENTRIQUE.......................................22
S2 VIS D’EXCENTRIQUE...........................................................8
T PIED....................................................................................................1
U BASE DE PIED............................................................................1
V CHARNIÈRE ................................................................................4
W RONDELLE ..................................................................................2
X POIGNÉE .......................................................................................2
Y FICHE AVEC TAMPONS ...................................................2
AA CACHE-TROUS........................................................................2
BB ÉTIQUETTE DE MISE EN GARDE...............................1
CC VIS NOIRE TÊTE LARGE 63,5 mm ..........................4
DD VIS NOIRE TÊTE PLATE 48 mm ................................4
EE VIS MARRON TÊTE PLATE 38 mm ........................3
FF VIS NOIRE TÊTE PLATE 14 mm .................................8
GG VIS NOIRE TÊTE GOUTTE DE SUIF 14 mm .....4
HH VIS NOIRE TÊTE PLATE 13 mm .................................8
II VIS MARRON TÊTE LARGE 11 mm .........................8
JJ VIS ARGENTÉE À MÉTAUX 6 mm ...........................2
KK CLOU ............................................................................................33
A EXTRÉMITÉ .................................................................................2
B MONTANT..................................................................................... 1
C MONTANT INFÉRIEUR ........................................................1
D DESSUS ..........................................................................................1
E DESSOUS ......................................................................................1
F
TABLETTE
...................................................................................... 1
G ARRIÈRE .........................................................................................1
H PORTE .............................................................................................2
I
PIED DROIT AVANT / PIED GAUCHE ARRIÈRE
........2
J
PIED GAUCHE AVANT / PIED DROIT ARRIÈRE
........2
K
BLOC D’EXTENSION............................................................2
L
MOULURE D’ARRÊT .............................................................1
M
MOULURE DE DESSUS ..................................................... 1
N
SOCLE ............................................................................................. 1
O
GLISSIÈRE SUPÉRIEURE .................................................2
P
GLISSIÈRE INFÉRIEURE ....................................................2
410627www.sauder.com/services
Page 19
ÉTAPE 1
Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans
cette étape.
Assembler l’élément sur un sol à moquette ou sur le carton vide
pour éviter d’endommager l’élément ou le sol.
Enfoncer trente EXCENTRIQUES ESCAMOTABLES (Q2) dans
les EXTRÉMITÉS (A), les MONTANTS (B et C), le DESSUS (D), le
DESSOUS (E), la TABLETTE (F) et un ensemble de
PIEDS (I et J). Insérer ensuite vingt-deux CHEVILLES
D'EXCENTRIQUE (R2) dans les
EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 2
Serrer huit VIS D'EXCENTRIQUE (S2) dans les PIEDS (I et J).
Fixer les PIEDS (I et J) aux EXTRÉMITÉS (A). Serrer quatre
EXCENTRIQUES ESCAMOTABLES.
Attention: Risque des dégâts ou blessures. Les Excentriques
Escamotables doivent être serrés à bloc. Les Excentriques
Escamotables que ne sont pas serrées à bloc peuvent desserrer
et les pièces peuvent séparer. Pour serrer à bloc, faire tourner
l'excentrique escamotable de 210 degrés.
ÉTAPE 6
Fixer l'EXTRÉMITÉ GAUCHE (A), le MONTANT (B) et le PIED
AVANT GAUCHE/ARRIÈRE DROIT (J) au
DESSUS (D) et MOULURE D'ARRÊT (L). Serrer cinq
EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 7
Fixer la TABLETTE (F) à l'EXTRÉMITÉ GAUCHE (A). Serrer deux
EXCENTRIQUES ESCAMOTABLES.
Fixer la TABLETTE (F) au MONTANT (B). Utiliser deux VIS NOIRES
TÊTE PLATE 48 mm (DD).
Fixer le MONTANT INFÉRIEUR (C) à la TABLETTE (F). Serrer deux
EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 3
Avec précaution, retourner les EXTRÉMITÉS (A).
Faire tourner huit VIS NOIRES TÊTE PLATE 14 mm (FF) dans les
EXTRÉMITÉS (A) jusqu’à ce que l’épaulement des TROUS repose
sur la surface des EXTRÉMITÉS.
Enfi ler les GLISSIÈRES (O et P) sur les EXTRÉMITÉS (A). Aligner
la rainure des GLISSIÈRES sur les têtes des VIS dans
les EXTRÉMITÉS.
ÉTAPE 8
Fixer le DESSOUS (E) à l'EXTRÉMITÉ GAUCHE (A). Serrer deux
EXCENTRIQUES ESCAMOTABLES.
Fixer le DESSOUS (E) au MONTANT INFÉRIEUR (C). Utiliser deux
VIS NOIRES TÊTE PLATE 48 mm (DD).
Enfi ler le SOCLE (N) sur le chant cranté du DESSOUS (E).
ÉTAPE 4
Avec précaution, retourner les EXTRÉMITÉS (A).
Fixer les PIEDS (I et J) aux EXTRÉMITÉS (A). Serrer quatre
EXCENTRIQUES ESCAMOTABLES.
Insérer deux CACHE-TROUS (AA) dans les trous
des PIEDS (I et J).
ÉTAPE 9
Fixer l'EXTRÉMITÉ DROITE (A) et le PIED AVANT DROIT/ARRIÈRE
GAUCHE (I) au DESSUS (D), DESSOUS (E), à la
TABLETTE (F) et MOULURE D'ARRÊT (L). Serrer sept
EXCENTRIQUES ESCAMOTABLES.
Fixer la MOULURE DE DESSUS (M) sur la MOULURE
D'ARRÊT (L). Utiliser trois VIS MARRON TÊTE PLATE 38 mm (EE).
Fixer les BLOCS D'EXTENSION (K) au DESSOUS (E). Utiliser
quatre VIS NOIRES TÊTE LARGE 63 mm (CC).
ÉTAPE 5
Fixer la MOULURE D'ARRÊT (L) au DESSUS (D). Serrer quatre
EXCENTRIQUES ESCAMOTABLES.
410627 www.sauder.com/servicesPage 20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Sauder 410627 Operating instructions

Sauder
Brand
Sauder
Model
410627
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents