Page is loading ...
Manual version: 6PW105-20190725 BOM:3123A0R9
i
H3C NSQ1TGS32SF0 interface module
1 Module view
Figure 1 NSQ1TGS32SF0 interface module
2 Specifications
Figure 2 Front panel
Table 1 Module specifications
Item S
p
ecification
Dimensions (H × W × D) 40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)
Power consumption 126 W to 170 W
Weight 3.45 kg (7.61 lb)
Hot swapping Supported
Connector type LC
Interfaces 32 10-GE-SFP+ ports
Interface transmission rate 10/1 Gbps
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Storage: –40°C to +70°C (–40°F to +158°F)
Ambient humidity
• Operating: 10% RH to 95% RH, noncondensing
• Storage: 5% RH to 95% RH, noncondensing
Manual version: 6PW105-20190725 BOM:3123A0R9
ii
Item S
p
ecification
Compatible device models
and slots
• M9006 gateway (slot 2 to slot 5)
• M9010 gateway (slot 0 to slot 3 and slot 6 to slot 9)
• M9014 gateway (slot 0 to slot 5 and slot 8 to slot 13)
• T9006 IPS (slot 2 to slot 5)
• T9010 IPS (slot 0 to slot 3 and slot 6 to slot 9)
• T9014 IPS (slot 0 to slot 5 and slot 8 to slot 13)
Table 2 describes the SFP+ transceiver modules available for the SFP+ ports on the module.
Table 2 SFP+ transceiver modules available for the SFP+ ports on the module
Optional
SFP+
module
Central
wavelength
(nm)
Connector
type
Fiber diameter
Modal
bandwidth
(MHz*km)
Maximum
transmission
distance
SFP-XG-SX-M
M850-A
850 LC
50/125 μm MMF
2000 300 m (984.26 ft)
500 82 m (269.03 ft)
400 66 m (216.54 ft)
62.5/125 μm MMF
200 33 m (108.27 ft)
160 26 m (85.30 ft)
SFP-XG-LX22
0-MM1310
1310 LC
62.5/125 μm MMF
500 220 m (721.78 ft)
50/125 μm MMF
500 220 m (721.78 ft)
400 100 m (328.08 ft)
SFP-XG-LX-S
M1310
1310 LC 9/125 μm SMF N/A 10 km (6.21 miles)
SFP-XG-LH40
-SM1550
1550 LC 9/125 μm SMF N/A 40 km (24.86 miles)
3 LEDs
The module provides a LED for each SFP+ port to indicate their operating status.
Table 3 SFP+ port LED description
LED Status Descri
p
tion
SFP+ port status LED
Flashing The SFP+ port is sending or receiving data.
On A link is present on the SFP+ port.
Off No link is present on the SFP+ port.
Manual version: 6PW105-20190725 BOM:3123A0R9
iii
4 Installing and removing the module
CAUTION:
• Wear a reliably-grounded ESD wrist strap when installing or removing the module.
• Do not touch the components on the module.
4.1
Installing the module
1. Face the front panel of the device.
2. Identify the slot to install the module, and remove the filler panel from the slot.
This manual uses slot 3 as an example.
3. Place the module on a flat surface with the components facing up. Open the ejector levers on the
module.
4. Gently push the module into the slot along the guide rails. (See callout 1 in Figure 3 .)
5. Close the ejector levers and make sure the module is in close contact with the backplane. (See
callout 2 in Figure 3 .)
6. Use a Phillips screwdriver to fasten the captive screws on the module. (See callout 3 in Figure 3 .)
Figure 3 Installing the module
(1) Gently push the module into the slot along the guide rails until the module is in close contact with the
backplane
(2) Close the ejector levers (3) Use a Phillips
screwdriver to fasten the captive screws
Manual version: 6PW105-20190725 BOM:3123A0R9
iv
4.2
Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is released.
2. Simultaneously open the ejector levers of the module to separate the module from the backplane,
and pull the module slowly out of the chassis along the guide rails.
3. Place the module on an anti-static workbench or put it in an anti-static bag, with the components
side facing up.
4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
Copyright © 2019 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
/