Page is loading ...
Manual version: 6PW105-20190725 BOM: 3123A1M0
i
H3C SecPath NSQM2GP24TSSC0 interface module
1 Identifier
The module identifier NSQM2GP24TSSC0 is in the upper right corner of the front panel.
2 About the module
The NSQM2GP24TSSC0 interface module provides twenty-four 1000BASE-X SFP fiber ports and
four 10GBASE-R SFP+ fiber ports. By using this module with high-performance service modules,
the device is capable of providing security for 100G networks.
3 Specifications
Figure 1 Front panel
(1) 1000BASE-X SFP fiber port LEDs (2) 10GBASE-R SFP+ fiber port LEDs
(3) 10GBASE-R SFP+ fiber ports (4) 1000BASE-X SFP fiber ports
(5) Ejector lever (6) Captive screw
IMPORTANT:
Before installing the module, you must remove the protection cover from the module.
Table 1 Module specifications
Item Specification
Dimensions (H × W × D) 40.1 × 399.2 × 354.8 mm (1.58 × 15.72 × 13.97 in)
SDRAM (DDR3) 1 GB
Power consumption 27 W to 52 W
Net weight 2.85 kg (6.28 lb)
Hot swapping Supported
Ports
• 24 × 1000BASE-X SFP fiber ports
• 4 × 10GBASE-R SFP+ fiber ports
Connector type LC
Manual version: 6PW105-20190725 BOM: 3123A1M0
ii
Item Specification
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Storage: –40°C to +70°C (–40°F to +158°F)
Ambient humidity
• Operating: 10% RH to 95% RH, noncondensing
• Storage: 5% RH to 95% RH, noncondensing
Port speed
• 1000 Mbps
• 10 Gbps
Transmission medium and max
transmission distance
1000BASE-X SFP fiber port: see Table 2.
10GBASE-R SFP+ fiber port: see Table 2 an
d Table 3.
Compatible device models and slots
• M9008-S gateway (slots 2 to 7)
• M9008-S-6GW gateway (slots 2 to 7)
• T9008-S intrusion prevention system (slots 2 to 7)
The 1000BASE-X SFP fiber ports support the SFP transceiver modules in Table 2. The 10GBASE-R
SFP+ fiber ports support SFP transceiver modules in Table 2
and SFP+ transceiver modules in Table
3.
Table 2 SFP transceiver modules available for the 1000BASE-X SFP fiber ports and
10GBASE-R SFP+ fiber ports
Module
Central
wavelength
(nm)
Connector
type
Cable
specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 LC
50/125 µm MMF 550 m (0.34 miles)
62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-LX-SM1310-A 1310 LC
9/125 µm SMF 10 km (6.21 miles)
50/125 µm MMF 550 m (1804.46 ft)
62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LH40-SM1310 1310 LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 LC 9/125 µm SMF 80 km (49.71 miles)
SFP-GE-LH100-SM1550 1550 LC 9/125 µm SMF 100 km (62.14 miles)
Table 3 SFP+ transceiver modules available for the 10GBASE-R SFP+ fiber ports
Module
Central
wavelength
(nm)
Connector
type
Cable
specifications
Maximum
transmission
distance
SFP-XG-SX-MM850-A 850 LC
50/125 µm MMF
300 m (984.25 ft)
82 m (269.03 ft)
66 m (216.54 ft)
62.5/125 µm MMF
33 m (108.27 ft)
26 m (85.30 ft)
SFP-XG-LX-SM1310 1310 LC 9/125 µm SMF 10 km (6.21 miles)
SFP-XG-LH40-SM1550 1550 LC 9/125 µm SMF 40 km (24.86 miles)
Manual version: 6PW105-20190725 BOM: 3123A1M0
iii
4 LEDs
The module provides a LED for each 1000BASE-X SFP fiber port and 10GBASE-R SFP+ fiber port
to indicate their operating status.
Table 4 1000BASE-X SFP fiber port LED description
Status Description
Flashing The port is sending or receiving data.
On A link is present on the port.
Off No link is present on the port.
Table 5 10GBASE-R SFP+ fiber port LED description
Status Description
Flashing The port is sending or receiving data.
On A link is present on the port.
Off No link is present on the port.
5 Installing and removing the module
CAUTION:
• Wear a reliably-grounded ESD wrist strap or ESD gloves when installing or removing the module.
• Do not touch the components on the module.
5.1
Installing the module
1. Face the front panel of the device. Remove the filler panel from the target slot.
This example uses slot 2.
2. Place the module on a flat surface with the components facing up. Open the ejector levers on
the module.
3. Push the module slowly into the slot along the guide rails.
4. Close the ejector levers and make sure the module is in close contact with the backplane.
5. Use a Phillips screwdriver to fasten the captive screws on the module.
Manual version: 6PW105-20190725 BOM: 3123A1M0
iv
Figure 2 Installing the module
5.2
Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is
released.
2. Simultaneously open the ejector levers of the module to separate the module from the
backplane, and pull the module slowly out of the slot along the guide rails.
3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component
side facing up.
4. If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
Copyright © 2019 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
/