H3C NSQ1GP24TXEA0 LPU User manual

Brand: H3C

Model: NSQ1GP24TXEA0 LPU

Type: User manual

H3C NSQ1GP24TXEA0 LPU is a powerful and versatile network device that can be used in a variety of applications. With its sixteen 1000/100 Mbps SFP ports, eight combo interfaces, and two 10GBASE-R-XFP ports, the NSQ1GP24TXEA0 LPU can handle a wide range of traffic loads and requirements. The device also supports hot swapping, making it easy to add or remove ports as needed.

The NSQ1GP24TXEA0 LPU is compatible with a variety of H3C devices, including the M9006 gateway, M9010 gateway, M9014 gateway, T9006 IPS, T9010 IPS, and T9014 IPS. This makes it an ideal choice for use in a variety of network environments.

Manual version: 6PW105-20181010 BOM: 3123A0R6

H3C NSQ1GP24TXEA0 LPU manual

1 Card view

Figure 1 NSQ1GP24TXEA0 LPU

2 Specifications

Figure 2 Front panel of the NSQ1GP24TXEA0

(1) 100/1000 Mbps SFP port (2) 10/100/1000BASE-T Ethernet port

(3) 10 Gbps XFP port (4) XFP port LED

(5) Ethernet port status LED (6) SFP port status LED

Table 1 LPU specifications

Item S

ecification

Dimensions (H × W × D) 40 × 399 × 352 mm (1.57 × 15.71 × 13.86 in)

Power consumption 54 W to 95 W

Weight 3.08 kg (6.79 lb)

Hot swapping Supported

Connector type

RJ-45

Interfaces

• Sixteen 1000/100 Mbps SFP ports

• Eight combo interfaces

• Two 10GBASE-R-XFP ports

Manual version: 6PW105-20181010 BOM: 3123A0R6

Item S

ecification

Transmission speed

• 1000/100 Mbps SFP ports—1000/100 Mbps, full duplex.

• 1000 Mbps copper Ethernet ports—1000/100/10 Mpbs, half/full duplex.

• 10 Gbps XFP ports—10 Gbps.

Ambient temperature

• Operating: 0°C to 45°C (32°F to 113°F)

• Storage: –40°C to +70°C (–40°F to +158°F)

Ambient humidity

• Operating: 10% RH to 95% RH, noncondensing

• Storage: 5% RH to 95% RH, noncondensing

Compatible device model

and slot

• M9006 gateway (slot 2 to slot 5)

• M9010 gateway (slot 0 to slot 3 and slot 6 to slot 9)

• M9014 gateway (slot 0 to slot 5 and slot 8 to slot 13)

• T9006 IPS (slot 2 to slot 5)

• T9010 IPS (slot 0 to slot 3 and slot 6 to slot 9)

• T9014 IPS (slot 0 to slot 5 and slot 8 to slot 13)

NOTE:

• The SFP ports and the 10/100/1000Base-T Ethernet ports on the LPU form one combo interfaces.

Only one port in a combo interface can work at a time.

• The 100/1000 Mbps SFP ports do not support SFP-GE-T transceiver modules.

• 10GBASE-R-XFP 10-GE ports can operate only in 10G forced full-duplex mode.

Table 2 SFP module specifications

Type

Central

wavelen

Connector

Cable

ecifications

Maximum

transmission

distance

SFP-GE-SX-MM850-A 850 nm LC

50/125 μm

multi-mode fiber

550 m (0.34 miles)

62.5/125 μm

multi-mode fiber

275 m (0.17 miles)

SFP-GE-LX-SM1310-A 1310 nm LC

9/125 μm single

mode fiber

10 km (6.21 miles)

SFP-GE-LH40-SM1310 1310 nm LC

9/125 μm single

mode fiber

40 km (24.86 miles)

SFP-GE-LH40-SM1550 1550 nm LC

9/125 μm single

mode fiber

40 km (24.86 miles)

SFP-GE-LH80-SM1550 1550 nm LC

9/125 μm single

mode fiber

80 km (49.71 miles)

SFP-GE-LH100-SM1550 1550 nm LC

9/125 μm single

mode fiber

100 km (62.14 miles)

SFP-GE-T N/A RJ-45

Category-5 twisted

pair cable

100 m (0.06 miles)

SFP-GE-LX-SM1310-BIDI

1490 nm

(receive)/1310

nm (transmit)

9/125 μm single

mode fiber

10 km (6.21 miles)

Manual version: 6PW105-20181010 BOM: 3123A0R6

iii

Type

Central

wavelen

Connector

Cable

ecifications

Maximum

transmission

distance

SFP-GE-LX-SM1490-BIDI

1490 nm

(transmit)/1310

nm (receive)

9/125 μm single

mode fiber

10 km (6.21 miles)

SFP-GE-LH70-SM1470-CW 1470 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1490-CW 1490 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1510-CW 1510 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1530-CW 1530 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1550-CW 1550 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1570-CW 1570 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1590-CW 1590 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-GE-LH70-SM1610-CW 1610 nm LC

9/125 μm single

mode fiber

70 km (43.50 miles)

SFP-FE-SX-MM1310-A 1310 nm LC

50/125μm

multi-mode fiber

2 km (1.24 miles)

62.5/125μm

multi-mode fiber

SFP-FE-LX-SM1310-A 1310 nm LC

9/125μm single

mode fiber

15 km (9.32 miles)

SFP-FE-LH40-SM1310 1310 nm LC

9/125μm single

mode fiber

40 km (24.86 miles)

SFP-FE-LH80-SM1550 1550 nm LC

9/125μm single

mode fiber

80 km (49.71 miles)

NOTE:

• BIDI modules use different central wavelengths in transmit and receive directions, in order to

implement bidirectional transmission of optical signals over the same fiber.

• BIDI modules must be used in pair. For example, if an SFP-GE-LX-SM1310-BIDI is used at one end,

an SFP-GE-LX-SM1490-BIDI must be used at the other end.

For supported XFP modules, see the following table.

Manual version: 6PW105-20181010 BOM: 3123A0R6

Table 3 Specifications of XFP modules

Optional XFP

module

Central

wavelen

Connector

Cable specifications

Maximum transmission

distance

XFP-SX-MM850 850 nm LC

50/125 μm multi-mode

optical fiber

300 m (984 ft)

XFP-LX-SM1310 1,310 nm LC

9/125 μm single-mode

optical fiber

10 km (6 miles)

XFP-LH40-SM1550 1,550 nm LC

9/125 μm single-mode

optical fiber

40 km (25 miles)

XFP-LH80-SM1550 1,550 nm LC

9/125 μm single-mode

optical fiber

80 km (50 miles)

3 LEDs

The NSQ1GP24TXEA0 provides LEDs to show the operating status of the LPU.

Table 4 RJ-45 Ethernet port LED description

LED status Descri

tion

Flashing The Ethernet port is receiving or sending data.

On A link is present.

Off No link is present.

Table 5 SFP port LED description

LED status Descri

tion

Flashing The SFP port is receiving or sending data.

On A link is present.

Off No link is present.

Table 6 XFP port LED description

LIN

ACT Descri

tion

On Flashing A link is present, and the XFP port is receiving or sending data.

On Off A link is present, but no data is being received or sent.

Off Off No link is present.

4 Installing and removing the NSQ1GP24TXEA0

CAUTION:

• Wear a reliably-grounded ESD wrist strap before you install or remove the LPU.

• Do not touch the surface-mounted components directly with your hands when you install or remove

the LPU.

Manual version: 6PW105-20181010 BOM: 3123A0R6

4.1

Installing the NSQ1GP24TXEA0

1. Face the front panel of the device.

2. Identify the slot to install the LPU, and remove the filler panel from the slot.

This manual uses slot 3 as an example.

3. Place the LPU horizontally with the surface-mounted components facing upward. Pull outward the

ejector levers and gently push the LPU in along the slot guide rails until the LPU is in close contact

with the backplane. (See callout 1 in Figure 3 .)

4. Push the ejector levers inward. (See callout 2 in Figure 3 .)

5. Tighten the captive screws with a Phillips screwdriver to secure the LPU in the slot. (See callout 3

in Figure 3 .)

Figure 3 I

nstalling an NSQ1GP24TXEA0

(1) Gently push the LPU in alon

the slot

uide rails until the LPU is in close contact with the backplane.

(2) Push the ejector levers inward. (3) Ti

hten the captive

screws

with a Phillips screwdriver.

4.2

Removing the NSQ1GP24TXEA0

1. Use a Phillips screwdriver to loosen the captive screws at both sides of the LPU until all pressure is

released.

2. Pull the ejector levers at both sides of the LPU outward, and pull the LPU along the guide rails until

it completely comes out of the backplane.

3. Place the LPU on an anti-static workbench with the surface-mounted components up, or put it in an

anti-static bag.

If no new LPU is to be installed, install a filler panel to prevent dust and ensure good ventilation in

the device.

The information in this document is subject to change without notice.

H3C NSQ1GP24TXEA0 LPU User manual

H3C NSQ1GP24TXEA0 LPU User manual

H3C NSQ1GP24TXEA0 LPU User manual

Related papers

Other documents