2. Focal Point
  3. Seem 4 LED Wall-to-Ceiling Recessed FSM4L-CXF

Focal Point Seem 4 LED Wall-to-Ceiling Recessed FSM4L-CXF Installation guide

  • Hello! I've reviewed the installation instructions for the Focal Point Seem 4 FSM4L-CXF LED luminaires. This document provides detailed steps for pre-drywall installation, including the placement of backer flanges and the installation of corner units, wall and ceiling housings, reflectors, electrical connections and lens fitting. I am ready to answer any questions you have about setting up your new lighting system.
  • Must the luminaire be installed before drywall?
    What should I do before starting the installation?
    Who should install the luminaires?
    What should be done to prevent electrical shock?
IS0492 Rev. G 2019 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 5
seem 4™ led wall to ceiling corners
FSM4L-CXF
focal point
corner units
s - start of run
c - ceiling
W - Wall
i - intermediate
e - end of run
key
poWer off
poWer on
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
attention
LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL.
configurations are run specific, please consult factory draWings before beginning installation.
flex whip
2"x6"
framing
feed
ceiling height
specified luminaire length
specified luminaire length
2"x6" framing reQuired on botH
sides of Wall mounted Housings
5.625" min
6.0" max
backer flange
(may be pre-installed
or sHipped loose)
mud flange
(sHipped loose)
parts lists
Housing spacer
(11699)
backer flange
(72001) (8-32x 3/8”
WASHER HEX HEAD SCREW)
mud flange (70005)
(8-32 x 5/16” FLAT
UNDERCUT HEAD SCREW)
included HardWare
reflector (70008)
(6-32 x 5/16 pan-Head
macHine screW)
sHipped installed
joiner bracket
(11849)
joiner
bracket
(11920)
tie Wire bracket
(12547)
tie-Wire bracket
screW (72010)
(8-18 x 1/4 self tapping
screW)
lens end piece
( a07670)
lens tool
(a09052-02)
(affixed to Housing.
one per run)
IS0492 Rev. G 2019 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 5
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
3a
ceiling units only
3b
4
1
5
2' - 4'
5' - 6'
7' - 8'
dryWall
tHickness orientation guide point position
3/8"1 X F
1/2"1 X E
5/8"1 X D
3/4"1 X C
7/8"1 X B
1"1 X A
11/8"1 Y G
11/4"2 Y F
13/8"2 Y E
11/2"2 Y D
15/8"2 Y C
13/4"2 Y B
17/8"2 Y A
2"2 X E
21/8"2 X D
A
X
orientation 1
orientation 2
Y
B
C
D
E
F
G
H
X
Y
backer flange placement guide
A
X
orientation 1
B
C
D
E
F
G
H
5/8”
5/8" dryWall
A
X
orientation 1
B
C
D
E
F
G
H
1/2”
1/2" dryWall
using tHe backer flange
placement guide from
page 1 determine tHe
proper placement of tHe
backer flange for your
dryWall tHickness.
if backer flanges Were
pre-installed skip to step 6
2
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
IS0492 Rev. G 2019 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 5
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
10 1111 119
78
corner units (c & W) installation
continue installing remaining ceiling units
12 13 1114
x4
x2
x4
Wall corner unit (W) only
15
116
install
spacers
every 12"
connect flex WHip
to ceiling unit
secure ceiling
unit to structure
above
16
make electrical connections
17
secure reflectors to Housing
(2 screWs per reflector)
IS0492 Rev. G 2019 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 5
install remaining Wall Housings
19 20 x4
18
install spacers every
12" in ceiling units &
remaining Wall units
(Wall unit sHoWn)
Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
1121 x4
24
secure reflectors
to Housing (2 screWs
per reflector)
11
22
remove
spacers
begin dryWall installation (ceiling units sHoWn)
25
attention
before beginning dryWall
installation consult guide on
page 2 to ensure tHe backer
flange is set at tHe correct
deptH for tHe dryWall.
26
dryWall
11
27 28 29
dryWall
mud
make electrical connections
23
install reflectors
starting from bottom
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls
and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0492 Rev. G 2019 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 5 of 5
30
gently slide
lens into corner
before installing
remaining lenses
31 32
2
1
DriVer serVice
REFERENCE INSTRUCTIONS ON INCLUDED
TOOL FOR LENS INSTALLATION.
EMERGENCY
SEE BATTERY MANUFACTURER
INSTRUCTIONS
emergency maximum mounting HeigHt:
13.00'
3
/