2. Focal Point
  3. Seem 6 LED Wall-to-Ceiling Recessed FSM6L-CXF

Focal Point Seem 6 LED Wall-to-Ceiling Recessed FSM6L-CXF Installation guide

  • Hello! I've reviewed the instructions for the Focal Point seem 6 FSM6L-CXF LED Luminaire. This document outlines the installation process for the wall to ceiling corner luminaires, including different configurations, hardware, and electrical connections. I'm ready to answer your questions about any specific aspect of the installation.
  • When should the luminaire be installed?
    What type of framing is required for wall-mounted housings?
    Where can the backer flange placement guide be found?
    How many screws are used to secure reflectors to housing?
IS0567 Rev. D 2021 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 5
seem 6™ led wall to ceiling corners
FSM6L-CXF
focal point
corner units
s - start of run
c - ceiling
W - Wall
i - intermediate
e - end of run
key
poWer off
poWer on
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
attention
LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL.
configurations are run specific, please consult factory draWings before beginning installation.
trimless mud-in
7.00"
177.8mm
hard surface
6.00"
152.4mm
flex whip
2"x6"
framing
feed
ceiling height
specified luminaire length
specified luminaire length
2"x6" framing reQuired on botH
sides of Wall mounted Housings
backer flange
(may be pre-installed
or sHipped loose)
mud flange
(sHipped loose)
parts lists
included HardWare
sHipped installed
backer flange
(72001) (8-32x 3/8”
WASHER HEX HEAD SCREW)
mud flange (70005)
(8-32 x 5/16” FLAT
UNDERCUT HEAD SCREW)
reflector screW
(72010)
lens tool
(a15966-01)
(affixed to Housing.
one per run)
joiner bulkHead
screW (72010)
joiner bulkHead
(a15570-01)
joiner
bracket
(a15328-01)
tie-Wire
bracket
(12547)
lens end piece
(a12498)
joiner bracket
screW
(72009)
tie-Wire
bracket
screW
(72010)
(8-18 x 1/4 self
tapping screW)
IS0567 Rev. D 2021 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 5
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
4a
ceiling units only
4b
5
1
6
2' - 4'
5' - 6'
7' - 8'
dryWall
tHickness orientation guide point position
3/8"1 X F
1/2"1 X E
5/8"1 X D
3/4"1 X C
7/8"1 X B
1"1 X A
11/8"1 Y G
11/4"2 Y F
13/8"2 Y E
11/2"2 Y D
15/8"2 Y C
13/4"2 Y B
17/8"2 Y A
2"2 X E
21/8"2 X D
A
X
orientation 1
orientation 2
Y
B
C
D
E
F
G
H
X
Y
backer flange placement guide
A
X
orientation 1
B
C
D
E
F
G
H
5/8”
5/8" dryWall
A
X
orientation 1
B
C
D
E
F
G
H
1/2”
1/2" dryWall
using tHe backer flange
placement guide from
page 1 determine tHe
proper placement of tHe
backer flange for your
dryWall tHickness.
if backer flanges Were
pre-installed skip to step 7
3
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
2
IS0567 Rev. D 2021 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 5
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
10 11
11
11
9
78
corner units (c & W) installation
continue installing remaining ceiling units
x2
15
connect flex WHip
to ceiling unit
secure ceiling
unit to structure
above
make electrical connections
12 13 11
14
16 17
secure reflectors to Housing
(4 screWs per reflector)
IS0567 Rev. D 2021 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 5
install remaining Wall Housings
18
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
begin dryWall installation (ceiling units sHoWn)
24
attention
before beginning dryWall
installation consult guide on
page 2 to ensure tHe backer
flange is set at tHe correct
deptH for tHe dryWall.
25
dryWall
26
18 20
x4
11
21 x4
make electrical connections
22
install
reflectors
starting
from bottom
23
secure reflectors
to Housing (4 screWs
per reflector)
AVOID ALL CONTACT WITH LED SURFACE,
LEDs ARE EASILY DAMAGED!
27
dryWall
mud
28
gently slide
lens into corner
before installing
remaining lenses
29
REFERENCE INSTRUCTIONS ON INCLUDED
TOOL FOR LENS INSTALLATION.
Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls
and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0567 Rev. D 2021 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 5 of 5
30
2
1
DriVer serVice
3
EMERGENCY
SEE BATTERY MANUFACTURER
INSTRUCTIONS
emergency battery
maximum mounting HeigHt: 18.00'
emergency circuit
maximum mounting HeigHt: 21.00'
/