ZALMAN ZM-VE200 SE Specification

Category
HDD/SSD enclosures
Type
Specification

This manual is also suitable for

Quick Guide
ZM-VE200SE
www.ZALMAN.com
Ver. 1.2
Please read this Manual before use
1
.COM
1. Precautions
2. Specications
3. System Requirements
We are not responsible for any damages due to improper use.
Product design and specifications may be revised to improve quality and
performance.
Avoid inserting any foreign objects into the device.
Keep device away from heat sources, direct sunlight, oil, and humid environment.
Do not let the device be wet. It may not be covered by Warranty.
It may have problem if
used near magnetic objects.
Exterior damage during use is not covered by Warranty.
CPU: Intel Pentium / 350 Mhz or above compatible CPU
O.S: Windows XP SP3 or above / Mac OS X 10.0 or above
Model
Spec.
ZM-VE200SE
Case Material Aluminum Alloy, Acryl, Poly Carbonate
Weight 98.5g
Dimensions 135.3(L) × 78.6(W) × 13.1(H)
Interface USB 2.0 / e-SATA
Quick Guide
ZM-VE200 Pouch Screw Driver & Bolts 2pcs
USB 2.0 Cable
4. Components
Quick Guide
2
.COM
5. Mounting a 2.5 HDD
2.5 HDD
2.5 HDD
1
3
2
4
6. Names of Parts
USB Port
Access LED
LCD Display
Jog Switch
e-SATA Port
Firmware Recovery
Write Protect Switch
Serial Number
(1) Appearances
3
.COM
HDD Mode (Wheel-down the Jog Switch and connect USB cable.)
Dual Mode (Push the Jog Switch and connect USB cable.)
HDD Temp.
Folder or iso File Name
HDD Status
Current Modeiso File Mount Status
Protection Mode
ODD Mode (Wheel-up the Jog Switch and connect USB cable.)
iso File Mounted to Virtual ODD
Write Protected
Select name folder.
HDD Status (Good / Warning / Critical)
Select name.iso le.
Read &
Write Enabled
O
H
(2) Display and Modes
7. Connecting to PC
(1) Connect / Disconnect with USB cable
(2) Connect / Disconnect with e-SATA cable
(Optional)
Connect device to PCs USB port using enclosed USB cable.
When disconnecting, please use Hardware Safety Removal on tray.
Connect device to PCs USB port and e-SATA port using enclosed USB cable
and e-SATA cable.
When removing, right mouse click on My Computer Manage
Device Manager Disk Drive, then remove with right mouse button.
D
D
23℃
4
.COM
8. Introduction
Begin of List
To previous le
To next le
Select le
End of List
Firmware Version
Move to previously selected iso le
:
Folder
:
:
Folder
:
*.iso
:
*.iso
Dual Mode
HDD Model
HDD Mode
HDD S/N
ODD Mode
VE200SE S/N
*.iso
*.iso
:
*.iso
(1) Using Jog Switch
(2) Menu Navigation
To use Virtual ODD, iso le must be located in the _iso folder of device.
Caution
Desired mode is set after waiting 3 seconds
This device supports Hot Swap using e-SATA. To use Hot Swap function, please
check in advance if PC motherboard supports Hot Swap function.
Connect e-SATA cable rst, then USB cable.(When removing, use reverse order.)
If cable is unplugged with force while operating, it may cause fatal error to the
system and device.
Caution
5
.COM
MEMO
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

ZALMAN ZM-VE200 SE Specification

Category
HDD/SSD enclosures
Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI