Extron FOX Matrix 14400 User manual

Type
User manual

This manual is also suitable for

User Guide
Fiber Optic Matrix Switchers
68-1539-02 Rev. F
05 19
FOX Matrix 320x
FOX Matrix 14400
Configurable Fiber Optic Digital Matrix Switchers
Safety Instructions
Safety Instructions • English
WARNING: This symbol, ,when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within the
product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron website,
www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer darauf
aufmerksam machen, dass im Inneren des Gehäuses dieses Produktes
gefährliche Spannungen herrschen, die nicht isoliert sind und die einen
elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad de
Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,
la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les
informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site
Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad avvertire
l’utente della presenza di tensione non isolata pericolosa all’interno del
contenitore del prodotto che può costituire un rischio di scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire
l’utente della presenza di importanti istruzioni di funzionamento e
manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento alla Guida
alla conformità normativa e di sicurezza di Extron, cod. articolo 68-290-01, sul
sito web di Extron,
www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej
zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron
bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-
01, na stronie internetowej Extron,
www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的这个标志意在警告用户产品机壳内有暴露的危险 电压
险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 , www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
FOX Matrix 3200 and 7200 Switchers • Introduction ii
Copyright
© 2008-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(
®
), registered service marks(
SM
), and trademarks(
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, Codec Connect, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global
Configurator, GlobalScripter, GlobalViewer, Hideaway, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork,
TouchLink, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple
Suppression), DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,
DSVP(Digital Sync Validation Processing), eLink, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP,
MicroDigital, Opti-Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink,
Show Me, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K , VideoLounge,
WebShare, XTRA, ZipCaddy, and ZipClip
安全記事 • 繁體中文
警告: 若產品上使用此號,是為使用者產品殼內存在著
可能會導致觸電之風險的未絕緣危險電
注意 產品上使用此符號,是為提醒使用者備隨附的手冊中
重要的操作和維(維修説明
有關安全性指導方法規遵守EMI/EMF 相容存取範圍和相關主題的詳細
訊,請瀏覽 Extron 網站www.extron.com然後參《Extron 安全性與法規
守手則編號 68-290-01
安全上の注意
日本語
警告: この が製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、電の危険があるを示していま
意:この が製上に表示されている場合は、の取明書
されている重作と保()のについてユーザー
を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項目
スト イト www.extron.com よ り Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ださい。
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합
니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
Battery Notice
This product contains a battery. Do not open the unit to replace the battery. If the
battery needs replacing, return the entire unit to Extron (for the correct address, see the
Extron Warranty section on the last page of this guide).
CAUTION: Risk of explosion. Do not replace the battery with an incorrect type. Dispose
of used batteries according to the instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.
Débarrassez-vous des piles usagées selon le mode d’emploi.
Class 1 Laser Product
Any service to this product must be carried out by Extron Electronics and its qualified
service personnel.
CAUTION: Using controls, making adjustments, or performing procedures in a manner
other than what is specified herein may result in hazardous radiation exposure.
NOTE: For more information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
Produit laser de classe1
Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par
ExtronElectronics et son personnel qualifié.
ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution de
procédures de manière contraire aux dispositions établies dans le présent document,
présente un risque d’exposition dangereuse aux radiations.
Remarque : Pour plus d'informations sur les directives de sécurité, les conformités de
régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le
«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.
Conventions Used in this Guide
Notifications
The following notifications are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
Risk of property damage.
Risque de dommages matériels.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01]
R
0004
00300
00400
00800
00600
[02]
35
[17] [03]
E X1# *X1** X2^* X2(* X2& CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the
capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specification are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.
Contents
Introduction............................................................ 1
About this Guide ................................................. 1
About the FOX Matrix Switchers ......................... 1
Fiber Cable Transmission Modes .................... 4
Definitions ........................................................... 4
Features ............................................................. 4
Installation .............................................................. 7
Setup and Installation Checklist .......................... 7
Get Ready ...................................................... 7
Configure the Matrix Switcher ......................... 7
Perform Physical Installation ........................... 7
Install Software ............................................... 7
Rear Panel Boards, Cabling, and Features .......... 8
I/O Boards .................................................... 10
Remote Port ................................................. 13
Ethernet Connection ..................................... 14
Reset Button and LED .................................. 15
Power Supply Modules and Indicator LEDs .. 15
Cooling Fan Assemblies................................ 15
Front Panel Features ......................................... 16
Reset Operations .............................................. 18
Performing Soft System Resets
(Resets 3, 4, and 5) ..................................... 19
Programming Guide ........................................... 20
Host Control Ports ............................................ 20
Serial Ports ................................................... 20
Ethernet (LAN) Port ....................................... 21
Host-to-Switcher Instructions ........................... 22
Switcher-initiated Messages ............................. 22
Switcher Error Responses ................................ 23
Using the Command and Response Tables ...... 23
Command and Response Table for
SIS Commands ........................................... 24
Command and Response Table for
IP- and SNMP-Specific SIS Commands ...... 32
Special Characters ........................................... 35
Matrix Software ................................................... 36
About this Program .......................................... 36
Software Operation via Ethernet ................... 36
Software Operation via a Serial Port .............. 37
Installing the Software ....................................... 37
Using the Matrix Switchers Control Program ..... 40
Starting the Program .................................... 40
IP Settings / Options Dialog Box ................... 43
Updating Firmware ....................................... 48
Uploading HTML Files ................................... 51
Windows Buttons, List Boxes, and
Trash Can .................................................... 52
Windows Menus ........................................... 52
Using Emulation Mode .................................. 56
Using the Help System ................................. 57
HTML Operation ................................................. 58
Opening the Embedded Web Pages ................. 59
Status Tab ........................................................ 60
System Status Page ..................................... 60
Input Link Page............................................. 61
Configuration Tab ............................................. 62
System Settings Page .................................. 62
Passwords Page........................................... 65
Email Settings Page ...................................... 66
SNMP Settings Page .................................... 68
Firmware Upgrade Page ............................... 70
File Management Tab ....................................... 71
File Management Page ................................. 71
Control Tab ....................................................... 72
Set and View Ties Page ................................ 72
FOX Matrix 320x and FOX Matrix 14400 • Contents v
Maintenance and Modifications ..................... 74
Mounting the Switcher ...................................... 74
UL Guidelines ............................................... 74
Mounting Instructions ................................... 75
Battery and Power Precautions ........................ 75
Removing and Installing an I/O Board or
Blank Panel ..................................................... 75
Removing an I/O Board or Blank Panel ......... 77
Installing an I/O Board or Blank Panel ........... 77
Removing and Installing a Power Supply
Module ............................................................ 78
Removing a Power Supply Module ............... 78
Installing a Power Supply Module ................. 79
Removing and Installing a Fan Module .............. 80
Removing a Fan Module ............................... 80
Installing a Fan Module ................................. 81
Ethernet Connection ......................................... 82
Ethernet Link .................................................... 82
Ethernet Connection ..................................... 82
Default IP Address ........................................ 82
Pinging to Determine the
Extron IP Address ........................................ 83
Pinging to Determine the
Web IP Address ........................................... 83
Configuring the Switcher for Network Use
via the ARP Command ................................ 84
Connecting as a Telnet Client ........................ 85
Telnet Tips .................................................... 86
Subnetting — A Primer ..................................... 87
Gateways ..................................................... 87
Local and Remote Devices ........................... 87
IP Addresses and Octets .............................. 88
Subnet Masks and Octets ............................ 88
Determining Whether Devices Are
on the Same Subnet .................................... 88
FOX Matrix 320x and FOX Matrix 14400 • Contents vi
Introduction
WARNING: The FOX matrix switcher outputs continuous invisible light (Class 1
rated), which may be harmful to the eyes; use with caution.
AVERTISSEMENT : Le grilles de commutation de la gamme FOX émet une lumière
invisible en continu (conforme à la classe1) qui peut être dangereux pour les yeux, à
utiliser avec précaution.
Do not look into the r
ear panel fiber optic cable connectors or into the fiber optic
cables themselves.
Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau arrière
ou dans les câbles fibre optique eux-mêmes.
Plug the attached dust cap into the optical transceiver when the fiber optic cable is
unplugged.
Branchez la pr
otection contre la poussière dans l’ensemble émetteur/récepteur
lorsque le câble fibre optique est débranché.
About this Guide
About the FOX Matrix Switchers
Definitions
Featur
es
About this Guide
This guide contains installation, configuration, and operating information for the Extron
FOX Matrix 320x Switcher and FOX Matrix 14400 Switcher. These customizable matrix
switchers support up to 320 (FOX Matrix 320x) or 144 (FOX Matrix 14400) inputs and outputs.
NOTE: In this guide, “FOX matrix switcher” and “switcher” refer to either switcher model
unless otherwise specified.
About the FOX Matrix Switchers
The FOX matrix switchers (see figure 1 on the next page for a FOX Matrix 14400 example)
distribute optical and electronic input signals to one or more optical and electronic outputs.
The matrix switchers can route multiple input and output configurations simultaneously. The
switchers are configurable, assembled from individual input/output (I/O) boards, each of
which supports 16 inputs by 16 outputs in a combination of the following types of board:
Singlemode and multimode fiber optic 16x16 I/O boards — These
non-pathologically compliant fiber optic boards route signals that are compatible with all
Extron FOX 500, FOXBOX, and PowerCage FOX fiber optic product lines.
FOX Matrix 320x and FOX Matrix 14400 • Introduction 1
FOX 3G I/O 1616 SM P board (available for FOX Matrix 14400 only) — This
pathologically-compliant fiber optic board passes digital signals in broadcasting
applications, while addressing the compatibility issues of passing pathological signals
generated from 3G-SDI, HD-SDI, and SDI signals over fiber optic systems, including
those defined by the RP 178 and RP 198 standards.
NOTE: This board is not available for the FOX Matrix 320x.
BNC 3G/HD/SD-SDI 16x16 I/O board — This pathologically-compliant board
supports and passes 3G-SDI, HD-SDI, and SD-SDI signals in their native (electronic)
format.
ANAHEIM, CA
RESET
RS232/RS422
REMOTE
LAN
ACT
LINK
100-240V
50/60Hz
1.2A MAX.
100-240V
50/60Hz
1.2A MAX.
REDUNDANT
PRIMARY
PRIMARY POWER SUPPLY
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REDUNDANT POWER SUPPLY
FAN ASSIMBLY
FAN ASSIMBLY
1 - 16
17 - 32
33 - 48
49 - 64
65 - 80
81 - 96
97 - 112
113 - 128
129 - 144
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
BCDEFGHI JKLMNOP
A
MM R
SM R
MM R
SM R
MM R
SM R
SM R
SM R
MM R
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
12V
0.3A MAX
FOX HDSDI
HD/SDI IN
POWER
BUFFERED OUTPUTS
MODE
OPTICAL
RxTX
12
FOX 2G AV Rx
Y/VID
O
U
T
P
U
T
S
RS-232
OVER FIBER
RS-232
REMOTE
Tx Rx Tx Rx
AUDIO
LR
RxTx
ALARM
12
R-Y
B-Y/C
S-VID
OPTICAL
POWER
12V
0.8A MAX
FOX 500 TX
100-240V 0.3A
50/60 Hz
AUDIO INPUTS
RGB INPUT
RGB
H/HV
V
OR
LR
RS-232
PASS THRU
TX Rx NA
RS-232
CONTROL
ALARM
*
OPTIONAL FOR
RETURN DATA
TX Rx 1 2
INPUT LOOP THRU
RGB
OPTICAL
12*
LINK
LINK
FOX 500 DVI TX
100-240V 0.3A
50/60 Hz
AUDIO INPUTS
LR
RS-232
PASS THRU
TX Rx NA
RS-232
CONTROL
ALARM
*
OPTIONAL FOR
RETURN DATA
TX Rx 1 2
OPTICAL
12*
LINK
LINK
DDC
RESOL
DVI - D INPUT
LOOP - THRU
FOX 500 DVI TX
100-240V 0.3A
50/60 Hz
AUDIO INPUTS
LR
RS-232
PASS THRU
TX Rx NA
RS-232
CONTROL
ALARM
*
OPTIONAL FOR
RETURN DATA
TX Rx 1 2
OPTICAL
12*
LINK
LINK
DVI - D OUTPUT
FOX 2G AV Tx
Y/VID
I
N
P
U
T
S
RS-232
OVER FIBER
RS-232
REMOTE
Tx Rx Tx Rx
AUDIO
LR
ALARM
12
R-Y
B-Y/C
S-VID
OPTICAL
POWER
12V
0.8A MAX
RxTx
FOXBOX 4G Tx VG A
RGB
AUDIO
OPTICAL
Rx
Tx
LINK
LINK
CONFIG
FOXBOX 4G Rx DVI
DVI
AUDIO
OPTICAL
Rx
Tx
LINK
LINK
CONFIG
FOX 500 Rx
100-240V 0.3A
50/60 Hz
AUDIO OUTPUTS
RGB OUTPUT
RGB
HV
LR
RS-232
PASS THRU
TX Rx NA
RS-232
CONTROL
ALARM
*
OPTIONAL FOR
RETURN DATA
TX Rx 1 2
S
RGB
OPTICAL
2* 1
LINK
LINK
12V
0.3A MAX
FOX HDSDI
HD/SDI IN
POWER
BUFFERED OUTPUTS
MODE
OPTICAL
RxTX
12
S
M
M
S
M
S
M
S
D
D
Multimode
I/O Board
D
3G-SDI/HD-SDI/SDI
I/O Board
Singlemode or
FOX 3G I/O 1616 SM P
I/O Board
S
FO
X 500 DVI Transmitter
Multimod
e
FOX 500 DVI Receiver
Multimode
FO
X AV Transmitter
Multimod
e
FOX AV Receiver
Multimode
FOX Matrix 14400
Modular Fiber Optic Matrix Switcher
FOXBOX DVI Receiver
Singlemode
FO
XBOX VGA Transmitter
Singlemode
FOX 500 RGB Receiver
Singlemode
FOX 3G HD-SDI Transceive
r
Singlemode
FO
X 500 RGB Transmitter
Multimod
e
FO
X 3G HD-SDI Transceiver
Multimod
e
Singlemode
Fiber Cable
Digital Cable
Multimode
Fiber Cable
H
CO
M
MUNI
C
A
TI
O
N
Tx
CO
MM
U
NI
C
A
T
I
O
N
Tx
HD Camera
Control
NOTE: All FOX 3G HD-SDI units are set
to bidirectional transceiver mode.
Figure 1. Typical FOX Matrix 14400 Application
NOTE: The non-pathologically compliant multimode and singlemode fiber optic I/O
boards are physically and functionally identical, with the exception of the effective
range of transmission. In this guide, any reference to fiber optic transmission
applies to either transmission mode unless otherwise specified. The pathologically-
compliant fiber optic I/O board is identified separately in this guide where appropriate.
By adding or removing I/O boards, the FOX matrix switcher is expandable and contractable
within the following ranges:
FOX Matrix 320x — Includes up to 20 I/O boards. It is expandable from a 16-input by
16-output matrix to a 320-input by 320-output matrix.
FOX Matrix 14400 — Includes up to 9 I/O boards. It is expandable from a 16-input by
16-output matrix to a 144-input by 144-output matrix.
The Extron proprietary fiber optic signal, generated by FOX 500, FOXBOX,
PowerCage FOX, and FOX II transmitters, can include video, stereo audio, and
transmitter-to-receiver RS-232 serial communications. The video component of the signal
can be of a variety of formats, depending on the transmitter and receiver:
RGB video Digital Visual Interface (DVI) video
3G-SDI, HD-SDI, or SDI video Low resolution (composite video or S-video)
FOX Matrix 320x and FOX Matrix 14400 • Introduction 2
NOTES:
Compatible optical signals are digital signals from 270 Mbps through 4.25 Gbps
that are sent and received via fiber optic small form factor pluggable (SFP) modules
with LC-type connectors. The FOX matrix switchers support all compatible optical
signals, whether transmitted or received by an Extron fiber optic system component
or not.
The FOX 500, FOXBOX, and PowerCage FOX transmitter
-to-receiver
communications, including the serial link, occupy one matrix switcher
input and output. This matrix switcher also supports the FOX 500 return
(receiver-to-transmitter) serial communications, but returning this signal stream to
the transmitter occupies a separate matrix switcher input and output.
The matrix switchers input and output the optical signals that they route on fiber optic
transceiver modules and the 3G-SDI, HD-SDI, and SDI video signals on BNC connectors.
The switcher has four (FOX Matrix 320x) or two (FOX Matrix 14400) internal, hot-swappable,
100 VAC to 240 VAC, 50-60 Hz, 400-watt power supplies that provide worldwide power
compatibility and reliability.
The matrix switcher is a single box solution to complex fiber optic and broadcast signal
routing applications. Each input and output is individually isolated and buffered. Any input
can be switched to any one output or all outputs with virtually no crosstalk or signal noise
between channels.
The matrix switcher can be remotely controlled using either the Extron Matrix Switchers
Control Program or the Simple Instruction Set (SIS) (see Programming Guide on page 20.
Control is available via the:
Rear panel Remote RS232/RS422 port
Rear panel LAN port
Fr
ont panel RS-232 serial Config (configuration) port
The SIS is a set of basic ASCII code commands that provide simple control through a
control system or PC without the need to enter long strings of code. SIS commands can be
entered via any of the ports listed above.
The switcher can be operated remotely by any of the following connected to a serial port or
LAN port:
Control system
PC computer
Extron FPC 6000 Front Panel Controller for FOX Matrix 320x and FOX Matrix 14400
Extr
on MKP 2000 remote control panel
Extron MKP 3000 remote control panel
(RS-232 or RS-422 only) Extron MCP 1000 remote control panel, an MKP 1000
remote keypad, or both
The matrix switcher is housed in a rack-mountable, metal enclosure with mounting flanges
for standard 19-inch racks. The sizes are as follows:
FOX Matrix 320x
— 17U high
FOX Matrix 14400 — 9U high
FOX Matrix 320x and FOX Matrix 14400 • Introduction 3
Fiber Cable Transmission Modes
Two versions of the non-pathologically compliant FOX matrix switcher fiber optic I/O
board are documented in this guide. They are categorized by the type of fiber optic cable,
multimode or singlemode, which defines the effective range of transmission:
Multimode — Long distance, up to 300 m (985 feet)
Singlemode — Very long distance, up to 30 km (18.75 miles)
NOTES:
All transceiver modules on a fiber optic I/O board, as delivered from Extron, are
configured the same: either all multimode or all singlemode.
Y
ou can mix multimode and singlemode fiber optic I/O boards in a
FOX matrix switcher, but ensure that you connect the proper transmission mode
fiber cables to the board.
Definitions
The following terms, which apply to all Extron matrix switchers, are used throughout this guide:
Tie — An input-to-output connection.
Set of ties — An input tied to two or more outputs. (An output can never be tied to
more than one input.)
Configuration — One or more ties or one or more sets of ties.
Current configuration — The configuration that is currently active in the switcher (also
called “configuration 0”).
Global memory preset — A configuration that has been stored. Up to 64 global
presets can be stored in memory. When a preset is retrieved from memory, it becomes
the current configuration. Presets can be saved and recalled via any of the serial ports
or the LAN port.
Room — A subset of outputs that are logically related to each other, as determined by
the operator. The switchers support up to 10 rooms, each of which can consist of from
1 to 16 outputs.
Room memory preset — A configuration that has been stored that consists of
outputs in a single room. When a room preset is retrieved from memory, it becomes the
current configuration. Up to 10 room presets can be associated with a room.
Features
Fiber optic inputs and outputs — With fiber optic I/O boards, the switchers input and
output fiber optic signals on SFP optical connectors. The fiber optic I/O boards support
digital signals from 270 Mbs through 4.25 Gbps.
SDI, HD-SDI, or 3G-SDI inputs and outputs — With 3G/SDI/HD-SDI I/O boards,
the switchers input and output SDI and HD-SDI signals on BNC connectors. The
3G/SDI/HD-SDI I/O boards support multi-rate SDI at rates up to 2.97 Gbps, and
comply with SMPTE 259M-C, 292M, 424M, and ITU digital video standards.
Cross-format compatibility
An input on an 3G/SDI/HD-SDI I/O board can be tied to an output on a fiber optic
I/O board or another 3G/SDI/HD-SDI I/O board.
An input on a fiber optic I/O board can be tied to an output on an 3G/SDI/HD-SDI
I/O board or another fiber optic I/O board.
FOX Matrix 320x and FOX Matrix 14400 • Introduction 4
Switching flexibility — The switcher provides individually buffered, independent matrix
switched outputs.
Any input can be tied to any or all outputs.
Quick multiple tie — Multiple inputs can be switched to multiple outputs
simultaneously. This allows all displays (outputs) to change from source to source at
the same time.
Input link detection — In critical environments or unmanned, remote locations, it
may be vital to know that sources are active and switching. The switcher confirms
that input sources are active by detecting light. Link detection provides instantaneous
feedback via the serial ports of the switchers or local-area network (LAN) port. The input
information can be displayed on any control system or in a control program on a LAN or
Internet (IP) connection.
Rooming — The switcher can be programmed to group multiple outputs to specific
“rooms,” allowing them to have their own presets.
Operational reliability — The FOX matrix switcher can support round-the-clock
operation in mission-critical applications, using a combination of hot-swappable
components and redundant power supplies.
Field upgradable, hot-swappable modular design — You can repair, upgrade,
reconfigure, or expand the matrix by simply installing a new I/O board or replacing a
board of one type with one of another. Hot-swappable components let you replace
any I/O board at any time without powering down the switcher.
Primary and redundant, hot-swappable power supplies — The hot-swappable,
externally accessible redundant power supply is configured to automatically take
over the load from the primary supply in the case of a failure.
The complete power circuit, from the plug, through the power supply, to the
insertion of the power onto the power distribution plane, is separate and redundant
(see figure 2). If the installation includes uninterruptible or completely separate
power sources, the switcher remains powered up through any power interruption
except a simultaneous loss of power on both power sources.
AC
Po
wer
Primary
Power
Supply
FOX Matrix 14400 FOX Matrix 320x
Redundant
Power
Supply
AC
Power
Primary
Power
Supply 2
Primary
Power
Supply 1
Redundant
Power
Supply 1
Redundant
Power
Supply 2
AC
Powe
r
AC
Power
Figure 2. Redundant Power Supply Backs Up Primary
The hot-swappable redundant power supply means no downtime for the switcher
and no loss of functionality should one power supply fail. Should a primary power
supply fail, the redundant power supply immediately assumes the load of the failed
primary supply. A failed power supply is easily replaceable from the rear at any time
without powering down the matrix and with no tools required.
Ease of maintenance — A failed power supply can be easily replaceable from the
rear at any time without powering down the matrix, and with no tools required.
Power supply status LEDs — Front panel and rear panel LEDs indicate the status
of the primary and redundant power supplies.
FOX Matrix 320x and FOX Matrix 14400 • Introduction 5
Hot-swappable fans — The hot-swappable, externally accessible fans allow quick
replacement to avert overheating in the case of a failure. Fans can be replaced
without powering down the switcher.
Operational flexibility — Operations such as input and output selection and setting
of presets can be performed via the Ethernet port or either serial port. The serial ports
allow remote control via a PC or a control system. The Ethernet link allows multiple
remote links with two levels of password protection. Remotely control the matrix
switcher using one or more of the following:
Windows
®
-based Matrix Switchers Control Program
Simple Instruction Set (SIS)
Remote control panels and keypads
SNMP support for remote monitoring — Supports the Simple Network
Management Protocol (SNMP) internet-standard protocol, allowing IT personnel to
manage devices on the IP network.
Laser controls — Non-pathologically compliant fiber optic boards can be set, via SIS
commands, to individually or globally disable the output laser drivers so that a driver
does not output light. They can also be set, individually or globally, to automatic so that
a driver turns on when a tie is made involving that driver or off when no tie is made.
Upgradeable firmware — The firmware that controls all switcher operation can
be upgraded in the field via either serial port or the Ethernet port, without taking
the switcher out of service. Firmware upgrades are available for download at
www.extron.com, and can be installed using the Matrix Switchers Control Program or
the embedded HTML pages.
Global memory presets — 64 global memory presets are a time-saving feature that
lets you set up and store input/output configurations in advance. You can then recall
those configurations when needed, with a few simple steps, via serial port or Ethernet
control.
Rack mounting — Rack mountable in any conventional 19-inch wide rack.
Permanent, rechargeable battery — The matrix switcher has a rechargeable lithium
battery to track time of day when power is disconnected.
WARNING: There is a danger of explosion if the battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the instructions of the
manufacturer.
AVERTISSEMENT : Si la pile est mal remplacée, il y a un risque d’explosion.
Remplacez la batterie seulement avec le même type ou un type similaire de pile,
recommandé par le fabricant. Débarrassez-vous des piles utilisées selon les
instructions du fabricant.
ATTENTION:
Non-Extron personnel must not attempt to remove the battery. Doing so voids
the warranty.
Du personnel ne faisant pas partie d’Extron ne doit pas essayer de retirer la
batterie. Cela annulerait la garantie.
FOX Matrix 320x and FOX Matrix 14400 • Introduction 6
Installation
This section details the installation and configuration of the FOX matrix switchers, including:
Setup and Installation Checklist
Rear Panel Boards, Cabling, and Features
Front Panel Features
Reset Operations
Setup and Installation Checklist
Get Ready
c Familiarize yourself with the matrix switcher.
c Obtain IP setting information for the matrix switcher from the local network administrator
(see Ethernet Connection, beginning on page 82).
Configure the Matrix Switcher
c Install the desired I/O boards (see Removing and Installing an I/O Board or Blank
Panel on page 75).
Perform Physical Installation
c If desired, install the switcher in a rack (see Mounting the Switcher on page 74).
c Cable input and output devices to the I/O ports (see I/O boards on page 10).
c As desired, connect computers, control systems, or both to the rear panel Remote port
(see Remote Port on page 13), LAN port (see Ethernet Connection on page 14), and
front panel Configuration port (see Front Panel Features on page 16).
c Connect power (see Power Supply Modules and Indicator LEDs on page 15).
c Test the switcher by creating a tie (see the Create ties SIS commands on page 25).
Install Software
c Install the Matrix Switchers Control Program (see Installing the Software on page 37).
FOX Matrix 320x and FOX Matrix 14400 • Installation 7
Rear Panel Boards, Cabling, and Features
ANAHEIM, CA
RESET
BI-LEVEL TRI-LEVEL
RS232/RS422
REMOTE
LAN
ACT
LINK
100-240V
50/60Hz
1.2A MAX.
100-240V
50/60Hz
1.2A MAX.
REDUNDANT
PRIMARY
PRIMARY POWER SUPPLY
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REDUNDANT POWER SUPPLY
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
1 - 16
17 - 32
33 - 48
49 - 64
65 - 80
81 - 96
97 - 112
113 - 128
129 - 144
FAN ASSEMBLY
FAN ASSEMBLY
SWITCH REFERENCE
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
3
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
AAA
BBB
HHH
GGGEEECCC DDDGGGFFFIII
Figure 3. FOX Matrix 14400 Switcher Rear Panel
A
Fiber optic boards with connectors and LEDs (see page 11)
B
3G-SDI, HD-SDI, and SDI boards with connectors and LEDs (see page 12)
C
Remote RS232/RS422 port (see page 13)
D
LAN connector (Ethernet connection) (see page 14)
E
Reset button and LED (see page 15)
F
Primary and Redundant AC power connectors (see page 15)
G
Power supply modules and indicator LEDs (see page 15)
H
Switch Reference BNCsPresent but not used on the FOX Matrix 14400.
Not present on the FOX Matrix 320x.
I
Cooling fan assemblies (see Removing and Installing a Fan Module on page 80)
FOX Matrix 320x and FOX Matrix 14400 • Installation 8
FAN ASSEMBLY
FAN ASSEMBLY
FAN ASSEMBLY
FAN ASSEMBLY
161 – 176177 – 192193 – 208209 – 224225 – 240241 – 256257 – 272273 – 288289 – 304305 – 320 145 – 160
Extron
REDUNDANT POWER SUPPLY 2
PRIMARY POWER SUPPLY 1
PRIMARY POWER SUPPLY 2
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
REDUNDANT
100-240V
~
50/60Hz
6.5A MAX
PRIMARY
100-240V
~
50/60Hz
6.5A MAX
Anaheim,
CA
REMOTE
RS232/RS422
N15799
C US
LISTED
1T23 I.T.E.
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
ABCDEF GHIJ MN O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
49 – 6465 – 8081 – 9697 – 112113 – 128129 – 144 1 – 1617 – 3233 – 48
RESET
LAN
ACT
LINK
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
KL
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
3
AAA
BBB
III
III
EEE
DDD
CCC
FFF GGG GGG GGG GGG
Figure 4. FOX Matrix 320x Switcher Rear Panel
FOX Matrix 320x and FOX Matrix 14400 • Installation 9
ATTENTION:
Use electr
ostatic discharge (ESD) precautions (be electrically grounded) when you
make connections. ESD is damaging, even if you cannot feel, see, or hear it.
Pr
enez des précautions contre les décharges électrostatiques (ESD) (soyez
électriquement relié à la terre) lorsque vous effectuez des connexions. Les ESD
peuvent endommager l’équipement, même si vous ne pouvez pas le sentir, le voir
ou l’entendre.
Remove system power befor
e making all connections.
Débranchez l’alimentation du système avant de faire n’importe quelle connexion.
I/O Boards
As shown in figure 5, each I/O board is identified by the input and output numbers supported
by the board position, which are printed on the side of each fan module (1 - 16, 17 - 32,
and so on). The transceiver modules on fiber optic I/O boards and BNC blocks on the
3G/HD/SD-SDI are identified as A through P.
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
1 - 16
17 - 32
33 - 48
49 - 64
FAN ASSIMBLY
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
O#1
Slot
2
No boar
d
installed
I#1
O#2
I#2
O#3
I#3
O#4
I#4
O#5
I#5
O#6
I#6
O#7
I#7
O#8
I#8
O#9
I#9
O#10
I#10
O#11
I#11
O#12
I#12
O#13
I#13
O#14
I#14
O#15
I#15
O#16
I#16
O#33
I#33
O#34
I#34
O#35
I#35
O#36
I#36
O#37
I#37
O#38
I#38
O#39
I#39
O#40
I#40
O#41
I#41
O#42
I#42
O#43
I#43
O#44
I#44
O#45
I#45
O#46
I#46
O#47
I#47
O#48
I#48
Location P
Output and Input
Location A
Output and Input
Slot 1
(1-16)
Slot
4
(49-64)
Slot 3
(33-48)
I/O Numbers
Figure 5. Arrangement of Inputs and Outputs on the I/O Boards
Each module, numbered from left to right, includes one of the outputs and one of the inputs
supported by the board. For example, the input and output numbers supported by the
I/O board in location 33 - 48 (slot 3) are as follows: A = 33, B = 34, C = 35, D = 36, E = 37,
F = 38, G = 39, H = 40, I = 41, J = 42, K = 43, L = 44, M = 45, N = 46, O = 47, and P = 48.
NOTE: On each transceiver module, the output is to the left of the input.
Slot Inputs and Outputs Slot Inputs and Outputs
1 1 through 16 11* 161 through 176
2 17 through 32 12* 177 through 192
3 33 through 48 13* 193 through 208
4 49 through 64 14* 209 through 224
5 65 through 80 15* 225 through 240
6 81 through 96 16* 241 through 256
7 97 through 112 17* 257 through 272
8 113 through 128 18* 273 through 288
9 129 through 144 19* 289 through 304
10* 145 through 160 20* 305 through 320
* FOX Matrix 320x only
FOX Matrix 320x and FOX Matrix 14400 • Installation 10
Fiber optic boards
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1
A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2
Figure 6. Fiber Optic Board
A
Fiber optic board, connectors (see figure 3 on page 8 and figure 4 on page 9)—
WARNING: The FOX matrix switchers fiber optic I/O boards output continuous
invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.
Plug the attached dust cap into the optical transceiver when the fiber optic cable
is unplugged.
AVERTISSEMENT : Le grilles de commutation de la gamme FOX cartes d’entrée/
sortie fibre optique émet une lumière invisible en continu (conforme à la classe1)
qui peut être dangereux pour les yeux, à utiliser avec précaution Branchez la
protection contre la poussière dans l’ensemble émetteur/récepteur lorsque le
câble fibre optique est débranché.
NOTES:
Ensure that you use the proper fiber cable for your I/O board. Typically,
singlemode fiber has a yellow jacket and multimode cable has an orange or
aqua jacket.
Unlike most Extron transmitters and receivers, which output an optical stream
on one connector in a block and receive a return optical stream on the second
connector in the same block, the FOX matrix switchers uses one connector
on the block as an input and the second connector on the same block as a
separate output.
All transceiver modules on a fiber optic I/O boar
d, as delivered from Extron, are
configured the same: either all multimode or all singlemode.
You can mix multimode and singlemode fiber optic I/O boards in a FOX matrix
switcher, but ensure that you connect the proper transmission mode fiber
cables to the board.
A1
Input connector and LED — For all one-way
video, audio, and serial communications output by a
transmitter, connect a fiber optic cable to the Input LC
connector (see figure 7).
Connect the far end of this fiber optic cable to the
Optical Tx LC connector on a FOXBOX Tx transmitter
or to any other compatible Extron fiber optic device.
NOTES:
For a FOX 500 transmitter, connect this fiber
optic cable to the Optical 1 LC connector.
Alternatively, for the serial return, (receiver-to-
transmitter) function, connect the far end of the
cable to the Optical 2 connector on a receiver.
Input LED — See Fiber optic I/O board LED
indications on the next page.
T
ransmitter
to
Receiver
OPTICAL
Rx
Tx
LINK
LINK
OPTICAL
Rx
Tx
LINK
LINK
A1
A2
Figure 7. Optical Connections
FOX Matrix 320x and FOX Matrix 14400 • Installation 11
A2
Output connector For all one-way video, audio, and serial communications
output to a receiver, connect a fiber optic cable to the Output LC connector (see
figure 7, on the previous page).
Connect the far end of this fiber optic cable to the Optical Rx LC connector on a
FOXBOX Rx receiver or to any other compatible Extron fiber optic device.
NOTES:
For a FOX 500 receiver, connect this fiber optic cable to the Optical Rx LC
connector.
Alter
natively, for the serial return, (receiver-to-transmitter) function,
connect the far end to the Optical 2 connector on a transmitter.
Output LED — See “Fiber optic I/O board LED indications,” below.
Fiber optic I/O board LED indications
On the fiber optic I/O boards, the input and output LEDs on the transceivers provide useful
indications of the status of the lasers and the reclocking function (see the table below).
OUT
IN
Definition
Output LED
indication
Input LED
indication Definition
Reclocked at 4.25 Gbps On On Reclocked at 4.25 Gbps
Not reclocked, laser off, or no signal Off Off Not reclocked or no signal
Non-4G signal present or not reclocked Fast blink Fast blink Non-4G signal present or not reclocked
NOTE: If the reclocking feature is bypassed (see the Set output reclocker SIS
command on page 26), the output LED is always on.
3G/HD/SD-SDI boards
A B C D E F G H I J K L M N O P
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
3G P BNC
B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2
B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1
Figure 8. 3G/HD/SD-SDI Board
B
BNC connectors (see figure 3 on page 8 and figure 4 on page 9) — Connect
inputs and output using the included DIN-to-female-BNC pigtail connectors, as
follows:
NOTE: The pigtails are not installed on the board during shipment.
To install the pigtails, press them onto the DIN connectors until
they snap into place.
To remove the pigtails, pull back on the knurled collar and pull the
pigtail straight back from the DIN connector.
B1
Multi-rate SDI Input connectors — Connect 3G-SDI, HD-SDI, or SDI
video inputs to these BNC connectors.
B2
Multi-rate SDI Output connectors — Connect digital displays to these BNC
connectors.
FOX Matrix 320x and FOX Matrix 14400 • Installation 12
Remote Port
C
Remote RS232/RS422 port (see figure 3 on page 8 and figure 4 on page 9) —
Connect a host device, such as a computer or touchpanel control, to the switcher via
this 9-pin D connector for serial RS-232 or RS-422 control (see figure 9).
RS-232 FunctionPin Function
1
2
3
4
5
6
7
8
9
Tx
Rx
Gnd
Not used
Transmit data
Receive data
Not used
Signal ground
Not used
Not used
Not used
Not used
Tx–
Rx–
Gnd
Rx+
Tx+
Not used
Transmit data (–)
Receive data (–)
Not used
Signal ground
Not used
Receive data (+)
Transmit data (+)
Not used
RS-422
1
5
6
9
REMOTE
RS-232/RS-422
Figure 9. Remote RS232/RS422 Connector
See Programming Guide, beginning on page 20, for definitions of the SIS commands
(serial commands to control the switcher via this connector) and Matrix Software,
beginning on page 36, for details on how to install and use the control software.
NOTE: The switcher can support either the RS-232 or the RS-422 serial
communication protocol, and can operate at 9600, 19200, 38400, or 115200
baud rates.
See the Command and Response Table for IP- and SNMP-Specific SIS
Commands on page 33 to configure this port under SIS control.
If desired, connect any of the following to the Remote RS232/RS422 connector:
Extron FPC 6000 Front Panel Controller for FOX Matrix 320x and FOX Matrix 14400
(see the FPC 6000 User Guide for details).
MKP 2000 remote control panel (see the MKP 2000 Remote Control Panel User
Guide for details)
MKP 3000 remote control panel (see the MKP 3000 Remote Control Panel User
Guide for details).
FOX Matrix 320x and FOX Matrix 14400 • Installation 13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Extron FOX Matrix 14400 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI