Extron FOXBOX T HD-SDI User manual

FOXBOX T HD-SDI
Extron
Brand
Extron
Model
FOXBOX T HD-SDI
Category
Network media converters
Type
User manual

Extron FOXBOX T HD-SDI is a fiber optic 3G/HD/SDI video transmitter that extends uncompressed digital SDI video signals up to 18.2 miles (29.3 km) over singlemode fiber using standard SFP modules, providing reliable signal transmission for broadcasting, post-production, and professional AV applications. It supports data rates up to 2.97 Gbps and resolutions up to 1080p60.

Extron FOXBOX T HD-SDI is a fiber optic 3G/HD/SDI video transmitter that extends uncompressed digital SDI video signals up to 18.2 miles (29.3 km) over singlemode fiber using standard SFP modules, providing reliable signal transmission for broadcasting, post-production, and professional AV applications. It supports data rates up to 2.97 Gbps and resolutions up to 1080p60.

User Guide
FOXBOX T HD-SDI
Fiber Optic Extenders
Fiber Optic 3G/HD/SDI Video Transmitter
68-2436-01 Rev. A
02 15
Safety Instructions
Safety Instructions • English
WARNING: This symbol, , when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within the
product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, , when used on the
product, is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron website,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT: Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur la présence à l’intérieur du boîtier du produit d’une
tension électrique dangereuse susceptible de provoquer un choc
électrique.
ATTENTION: Ce pictogramme, , lorsqu’il est
utilisé sur le produit, signale à l’utilisateur des
instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la
documentation fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la réglementation,
la compatibilité EMI/EMF, l’accessibilité, et autres sujets connexes, lisez les
informations de sécurité et de conformité Extron, réf. 68-290-01, sur le site
Extron, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll
dem Benutzer in der im Lieferumfang enthaltenen
Dokumentation besonders wichtige Hinweise zur
Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se
utiliza en el producto, avisa al usuario de la
presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación
proporcionada con el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad de
Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: www.extron.com,
номер по каталогу - 68-290-01.
Chinese Simplified（简体中文）
警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意： 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见
Extron 安全规范指南，产品编号 68-290-01。
Chinese Traditional（ )
警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意 若產品上使用此符號，是為了提醒使用者。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳
細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與
法規遵守手冊》，準則編號 68-290-01。
Japanese
警告: この記号 が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意: この記号 が製品上に表示されている場合は、本機の取扱説明書
に 記 載されている重 要な 操 作と保 守 (整備)の指 示につ いてユーザー の 注
意を喚起するものです。
安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウェ ブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。
Korean
경고: 이 기호 , 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 , 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part15 of the FCC rules. The ClassA limits provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference. This interference must be corrected at
the expense of the user.
Copyright
© 2015 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks
(SM)
, and trademarks
(TM)
are the property of
RGBSystems, Inc. or Extron Electronics:
Registered Trademarks
(®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, GlobalViewer, Hideaway, Inline, IPIntercom,
IPLink, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, Pure3, Quantum, SoundField, SpeedMount, SpeedSwitch,
SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS (Class D Ripple Suppression),
DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConfigurator, DSPConfigurator, DSVP (Digital Sync
Validation Processing), DTP, eLink, EQIP, FastBite, FlexOS, FOXBOX, Global Configurator, IP Intercom HelpDesk, LinkLicense, MAAP,
MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Scope-Trigger, ShareLink, SIS, Simple Instruction Set, Skew-Free,
SpeedNav, Triple-Action Switching, WebShare, XTRA, ZipCaddy, ZipClip
Class 1 Laser Product
Any service to this product must be carried out by Extron Electronics and its qualified
service personnel.
NOTE: For more information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety
and Regulatory Compliance Guide” on the Extron website.
Produit laser de classe1
Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par
ExtronElectronics et son personnel qualifié.
Remarque : Pour plus d'informations sur les directives de sécurité, les conformités
de régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien,
consultez le «Informations de sécurité et de conformité Extron» sur le site
internet d'Extron.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]
E X! *X1^* X1** X2#* X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” is the capital
letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
viiFOXBOX T HD-SDI Fiber Optic Transmitter • Contents
Introduction ...................................................1
About this Guide ................................................. 1
About the FOXBOX T HD-SDI Transmitter ........... 1
System Compatibility ...................................... 2
Features ............................................................. 3
Installation and Operation ........................... 4
Connections and Features .................................. 4
Rear Panel ...................................................... 4
Front Panel ..................................................... 8
Indications and Operation ................................... 9
Indications ...................................................... 9
Operation ....................................................... 9
Programming Guide ....................................10
Configuration Port ............................................ 10
Host-to-Transmitter Communications ............... 10
Unit-initiated Messages .................................... 10
Error Responses ............................................... 11
Timeout ............................................................ 11
Using the Command and Response Table ........ 11
Symbol Definitions ........................................ 11
Equipment Mounting .................................. 15
Mounting the Transmitter .................................. 15
Tabletop Use ................................................ 15
Mounting kits ................................................ 15
UL Rack-Mounting Guidelines ...................... 15
Contents
FOXBOX T HD-SDI Fiber Optic Transmitter • Contents viii
FOXBOX T HD-SDI Fiber Optic Transmitter • Introduction 1
Introduction
WARNING: The FOXBOX T HD-SDI outputs continuous invisible light (Class 1 rated),
which may be harmful to the eyes; use with caution.
• Do not look into the rear panel fiber optic cable connectors or into the fiber optic
cables themselves.
• Plug the attached dust cap into the optical transceiver when the fiber optic cable is
unplugged.
AVERTISSEMENT : Le FOXBOX T HD-SDI émet une lumière invisible en continu
(conforme à la classe1) qui peut être dangereux pour les yeux, à utiliser avec
précaution.
• Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau arrière
ou dans les câbles fibre optique eux-mêmes.
• Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur
lorsque le câble fibre optique est débranché.
• About this Guide
• About the FOXBOX T HD-SDI Transmitter
• Features
About this Guide
This guide describes how to install, operate, and configure the following Extron
FOXBOX T HD-SDI fiber optic transmitters.
• FOXBOX T HD-SDI SM — A singlemode, very long distance (up to 30 km [18.75
miles]) transmitter.
• FOXBOX T HD-SDI MM — A multimode, long distance (2 km [6,561 feet]) transmitter.
NOTE: The two products are physically and functionally identical, with the exception of
the effective range of transmission. The term “transmitter” refers to either product.
About the FOXBOX T HD-SDI Transmitter
The FOXBOX T HD-SDI transmits 3G HD-SDI, HD-SDI, and SDI video and embedded digital
audio via a single fiber optic cable (see figure 1, on the next page). A compatible Extron
fiber optic receiver receives the image and outputs the video and audio. The transmitter can
also send, on the same fiber optic cable:
• Optional analog audio
• RS-232 control signals
With a second fiber optic cable, the transmitter can receive RS-232 responses from the
connected receiver.
NOTE: The RS-232 communications are a passive pass-through only. The transmitter
does not generate or respond to the RS-232 communication signals.
FOXBOX T HD-SDI Fiber Optic Transmitter • Introduction 2
FOXBOX T HD-SDI
POWER
3G/HD/SDI LOOP THRU
AUDIO
OPTICAL
RS-232
ALARM
Tx Rx G1 2
RxTx
INPUTSOVER
FIBER
12V
0.5A MAX
POWER
12V
--A MAX
G
Tx Rx RTSCTS
COM 1
G
Tx Rx
COM 2
VCG
VOL
RELAYS
1 2 C
1 2 3 4 G
DIGITAL I/O
PWR OUT = 6W
eBUS
+V +S
-S
G
LAN
IPCP PRO 250
IR/S
S G
FOXBOX SR HDMI
LINK
LINK
OPTICAL
RxTx
HDMI
AUDIO
OUTPUTS
REMOTE
RS-232
Tx Rx
RS-232
OVER FIBER
ALARM
Tx Rx 1 2
POWER
12V
1.0 A MAX
LR
OFF
ON
HDMI AUDIO
POWER STANDBY
MODEL 80
FLAT PANEL
Help
System
Off
Display
Room
Control
Off
Mute
Screen
Lighting
December 15, 2013 - 7:58 AM
Audio
Control
Volume
Mute
Tuner
1 2 3
VCRLaptop PC DVD
Doc
Cam
Tuner
On
Channel
Last
Presets
More
Presets
321
654
987
Enter
0
RS-232
Ethernet
Ethernet
PTZ Camera
Display
RS-232
Ext
ron
FO
XBOX T HD-SDI
Fi
ber Optic Transmitter
3G-SDI
HDMI
Extron
FOXBOX SR HDMI
Fiber Optic Receiver
TCP/IP
Network
Extron
TLP Pro 1020T
10" Tabletop
TouchLink
Pro Touchpanel
Extron
IPCP Pro 250
IP Link Pro
Control
Processor
Up to 30 km (18.75 miles) singlemode ber SM Model
Figure 1. Typical FOXBOX T HD-SDI Application
System Compatibility
The FOXBOX T HD-SDI is compatible with all FOX matrix switchers and the following
receivers and accessory products.
The transmitter supports Plus or Non-Plus mode transmission for compatibility with FOX
receivers.
• Non-Plus mode transmission — Supports resolutions from 480i up to 1080p at
60 Hz. Embedded audio is not supported, but analog audio is supported.
• Plus mode transmission — Supports all of the resolutions in non-plus mode, in
addition to 2048x1080 at 60 Hz. Embedded audio and analog audio are supported.
FOX Receivers
Plus mode
FOX Receivers
Non- Plus mode
Other Products
FOXBOX Rx DVI PLUS FOXBOX Rx VGA FOX AEX 108
FOXBOX Rx HDMI FOXBOX Rx DVI PowerCage FOX AEX 104
FOXBOX SR HDMI FOX 500 DVI Rx FOX II AEX 108
PowerCage FOX Rx DVI Plus FOX 500 Rx PowerCage FOX II AEX 104
PowerCage FOX Rx HDMI PowerCage FOX Rx VGA FOX RS 104
PowerCage FOX SR HDMI PowerCage FOX Rx DVI FOX II RS 104
FOX II R DP FOX DA8 Plus
FOXBOX T HD-SDI Fiber Optic Transmitter • Introduction 3
Features
Extends 3G-SDI, HD-SDI, and SDI signals very long distances over a single fiber —
The FOXBOX T HD-SDI supports multi-rate SDI at rates from 270 Mbps to 2.97 Gbps,
and complies with SMPTE 259M-C, 292M, 424M, and ITU digital video standards. The
transmitter is compatible with FOX Series DisplayPort, HDMI, DVI, and VGA receivers.
Video input — The FOXBOX T HD-SDI inputs digital video on a BNC connector and
unbalanced stereo audio on 3.5 mm stereo mini jack.
Buffered 3G-SDI/HD-SDI/SDI loop-through — The transmitter has a buffered
SDI/HD-SDI BNC connector that allows connection of a local monitor.
Input equalization and reclocking on buffered outputs — The FOXBOX T HD-SDI
automatically equalizes incoming multi-rate SDI signals, and reshapes and restores signals
on its buffered outputs.
Audio Embedding — Converts analog stereo audio signal to two-channel PCM digital audio.
Embedded AES audio support — The FOXBOX T HD-SDI can transmit the selected AES
channel pair of the embedded digital audio.
Audio gain and attenuation adjustment capability
SD Pro processing deinterlaces standard definition 480i and 576i video — Provides
compatibility with HDMI and DVI-equipped displays, without the need for additional scalers.
Bidirectional RS-232 signals over fiber optic cable for AV device control —
Bidirectional RS-232 control pass-through allows the remote device to be controlled without
the need for additional cabling. Two fibers are required for bidirectional communications.
Real-time status LED indicators for troubleshooting and monitoring
Alarm notification for fiber link loss — The FOXBOX T HD-SDI can trigger an external
control system for immediate notification when a fiber link has been lost. Requires a second
fiber link.
Small form factor pluggable (SFP) modules with Industry standard LC fiber optics
connectors — Provide reliable physical connectivity and precise fiber core alignment.
1-inch high, quarter rack width, metal enclosures — With low profile enclosures, the
transmitter can be discreetly installed in various locations.
Front panel USB configuration port — Provides convenient access for setup and
configuration, including audio channel and group assignment.
Multimode and singlemode models — Available as an 850 nm multimode model for
long-range transmissions up to 2 km (6,560 feet), and a 1310 nm singlemode model for
extreme distances up to 30 km (18.75 miles).
Compatible with the following Extron FOX Series products:
• FOX Matrix switchers for signal distribution systems up to 1000x1000 and larger
• FOX series DisplayPort, HDMI, DVI plus, DVI, and VGA receivers from 480i up to
2048x1080 at 60 Hz
• FOX series DVI and VGA receivers 480i up to 1080p at 60 Hz
NOTE: The FOXBOX T HD-SDI is not compatible with FOX 3G HD-SDI,
FOX 3G DVC, or FOX AV models.
Rack mountable — The unit is rack mountable in any conventional 19-inch wide rack,
using any of a variety of Extron rack shelves.
Energy-efficient external universal power supply — The 100 VAC to 240 VAC external
power supply provides worldwide power compatibility, with high demonstrated reliability, low
power consumption, and reduced operating costs.
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 4
Installation and
Operation
This section describes the installation and the operation of the FOXBOX T HD-SDI
Transmitter, including:
• Connections and Features
• Indications and Operation
NOTE: For equipment mounting, see Mounting the Transmitter on page 15.
Connections and Features
Rear Panel
FOXBOX T HD-SDI
POWER
3G/HD/SDI LOOP THRU
AUDIO
OPTICAL
RS-232
ALARM
Tx Rx G12
RxTx
INPUTS OVER
FIBER
12V
0.5A MAX
CCBBAAGG FFDD EE
Figure 2. FOXBOX T HD-SDI Transmitter Connectors
A
3G/HD/SDI input port (see below )
E
Optical port and LEDs (see page 5)
B
Loop-Thru port (see below)
F
Alarm port (see page 5)
C
Audio input port (see below)
G
Power connector (see page 6)
D
Over Fiber port (see page 5)
A
3G/HD/SDI input port — Connect a 3G-SDI, HD-SDI, or SDI video input to
3G/HD/SDI
this BNC connector. The transmitter also accepts embedded digital audio on
this port.
B
Loop-Thru port — Connect a local digital display to this BNC connector for
LOOP THRU
a buffered loop-through of the input signal.
C
Audio input port — If desired, plug an analog audio input into the transmitter
A
UDI
O
via this stereo mini jack connector. This input can be selected in place of the audio
embedded in the 3G/HD/SDI input for the Loop-Thru output using the Select
audio input SIS command (see page 12).
NOTE: See the figure at right to identify the
connector tip, ring, and sleeve when you are
making connections for the transmitter from
existing audio cables. A mono audio connector
consists of the tip and sleeve. A stereo audio
connector consists of the tip, ring, and sleeve.
Sleeve ( )
Ring (
-
)
Tip (+)
3.5 mm Stereo Plug Connector
(balanced)
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 5
D
Over Fiber RS-232 port — Connect a serial RS-232 signal to the three
RS-232
ALAR
M
Tx Rx G
12
OVER
FIBER
leftmost poles of this 3.5 mm, 5-pole captive screw connector for RS-232
communication (see RS-232 connector wiring on page 7 to wire the
connector).
E
Optical port and LEDs —
WARNING: The FOXBOX T HD-SDI outputs continuous invisible light (Class 1
rated), which may be harmful to the eyes; use with caution. Plug the attached
dust cap into the optical transceiver when the fiber optic cable is unplugged.
AVERTISSEMENT : Le FOXBOX T HD-SDI émet une lumière invisible en continu
(conforme à la classe1) qui peut être dangereux pour les yeux, à utiliser avec
précaution Branchez la protection contre la poussière dans l’ensemble émetteur/
récepteur lorsque le câble fibre optique est débranché.
NOTES:
• Ensure that you use the proper fiber cable for your transmitter/receiver pair.
Typically, singlemode fiber has a yellow jacket and multimode cable has an
orange or aqua jacket.
• Only one fiber optic cable, transmitter Tx to receiver Rx, is required for video,
audio, and serial command transmission. But, if you connect only one fiber
optic cable, or if the connected receiver is configured to daisy-chain the optical
signal, system functionality is reduced. You will not receive RS-232 reports
from the controlled device. To receive responses from the controlled device and
for full functionality, you need to install both fiber optic cables and
leave the connected receiver in normal configuration (see the
User Guide for the connected receiver).
Ò
Tx (required) — For all one-way video, audio, and serial
communications from the transmitter to the receiver, connect a
fiber optic cable to the Tx LC connector.
Connect the opposite end of this fiber optic cable to the Rx
connector on a compatible receiver.
Ù
Rx (optional) — Connect a fiber optic cable for all one-way return
serial communications from the receiver to the transmitter.
Connect the opposite end of this fiber optic cable to the Tx
connector on a compatible receiver in normal configuration (see
the User Guide for the connected receiver).
Tx Link and Rx Link LEDs — When lit, the link is active (light is
received).
F
Alarm port — For remote monitoring of the received fiber optic link (Rx),
RS-232
ALAR
M
Tx Rx G
12
OVER
FIBER
connect a locally-constructed or furnished monitoring device to the
transmitter via the two rightmost poles (1 and 2) of this 5-pole captive screw
connector. When the transmitter does not detect a light link on fiber cable Rx
(optional), pin 1 and pin 2 of this port are shorted together (see Alarm
outputs connection on page 8 to wire this connector).
Tr
ansmitter
to
Receiver
OPTICAL
Rx
Tx
LINK
LINK
Ò
ÒÙÙ
OPTICAL
RxTx
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 6
G
Power connector — Plug the included external 12 VDC power supply into this 2-pole
connector.
ATTENTION:
• Do not connect power to the FOXBOX T HD-SDI until you have read the
CAUTION and ATTENTION notices below and on page 7.
• Ne branchez pas l’alimentation au FOXBOX T HD-SDI avant d’avoir lu les deux
rubriques « ATTENTION » aux pages 6 et 7.
Connector and cable details
Power supply wiring
Figure 3 shows how to wire the connector. Use the supplied tie-wrap to strap the power
cord to the extended tail of the connector.
Power Supply
Output Cord
Captive Screw
Connector
SECTION A–A
Ridges
Smooth
AA
Tie Wrap
3
5
Figure 3. Power Connector Wiring
CAUTION:
ATTENTION :
• The wires must be kept separate while the power supply is plugged in. Remove
power before wiring.
• Les deux cordons d’alimentation doivent être tenus à l’écart l’un de l’autre quand
l’alimentation est branchée. Couper l’alimentation avant de faire l’installation
électrique.
• The length of exposed wires is important. The ideal length is 3/16 inch (5 mm).
• Any longer and the exposed wires may touch, causing a short circuit.
• Any shorter and the wires can be easily pulled out even if tightly fastened by the
captive screws.
• La longueur des câbles exposés est importante. La longueur idéale est de 5mm
(3/16inches).
• S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et
provoquer un court circuit.
• S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par
les vis captives.
• Do not tin the power supply leads before installing them in the connector. Tinned
wires are not as secure in the connector and could be pulled out.
• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 7
ATTENTION:
• This product is intended to be supplied by a UL Listed power source marked
“Class 2” or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply
supplied by or specified by Extron. Use of an unauthorized power supply voids all
regulatory compliance certification and may cause damage to the supply and the
end product.
• Ce produit est destiné à une utilisation avec une source d’alimentation listéeUL avec
l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A minimum. Utilisez
toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation
d’une source d’alimentation non autorisée annule toute conformité réglementaire et
peut endommager la source d’alimentation ainsi que le produit final.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to a
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16. La source d’alimentation ne devra pas être fixée de
façon permanente à une structure de bâtiment ou à une structure similaire.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord (see figure 3 on the
previous page) identify the power cord negative lead.
• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte
pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du
cordon (voir l’illustration 3 sur la page 6) permettent de repérer le pôle négatif du
cordon d’alimentation.
To verify the polarity before connection, plug in the power supply with no load and check the
output with a voltmeter.
RS-232 connector wiring
Figure 4 shows how to wire the RS-232 connector.
RxTx Gnd
RS-232
ALARM
Tx Rx G 12
FIBER
Figure 4. RS-232 Connector Wiring
NOTES:
• The RS-232 Tx and Rx line pair must cross once between this connector and the
source or destination.
• The length and preparation of exposed wires is important (see the second and third
English language power connector CAUTION bullets on page 6 for details).
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 8
Alarm outputs connection
Pin 1 and pin 2 are
shorted together when
no light is detected.
Do not tin the wires!
RS-232
ALARM
Tx Rx G 12
OVER
FIBER
Figure 5. Alarm Connector
NOTE: The length of the exposed (stripped) copper wires is important (see the second
and third English language power connector CAUTION bullets on page 6 for details).
Front Panel
FOXBOX T HD-SDI
RATE
2.97 Gbps
Extron
CONFIG
1.485 Gbps
270 Mbps
Unknown
AUDIO
AA
Figure 6. FOXBOX T HD-SDI Transmitter Configuration Connector
A
Configuration port — Plug a computer or other device into the transmitter via this
USB mini-B port for remote control of the transmitter using SIS commands. See
Programming Guide, beginning on page 10 for a detailed listing of SIS commands.
FOXBOX T HD-SDI Fiber Optic Transmitter • Installation and Operation 9
Indications and Operation
Indications
All indicators are on the front panel (see figure 7).
FOXBOX T HD-SDI
RATE
2.97 Gbps
Extron
CONFIG
1.485 Gbps
270 Mbps
Unknown
AUDIO
AA BB CC
Figure 7. FOXBOX T HD-SDI Transmitter Indicators
A
Power indicator — Indicates that the transmitter is receiving power.
B
Rate indicators — Indicate the input video rate detected on the 3G/HD/SDI input BNC.
The recognized rates are 2.97 Gbps, 1.485 Gbps, and 270 Mbps. The Unknown LED
indicates that an input is detected, but that the transmitter does not recognize the rate.
NOTES:
• All four Rate LEDs blink repeatedly if a fiber optic connector module on the rear
of the unit is unseated.
• The transmitter equalizes and distributes the input whether it recognizes the
rate or not.
C
Audio indicator — Indicates that the transmitter is detecting a digital or analog audio
input.
Operation
After the transmitter, the connected receiver, and their connected devices are powered up,
the system is fully operational. If any problems are encountered, verify that the cables are
routed and connected properly, and that the display device has the proper resolution and
refresh rate selected. If your problems persist, call the Extron S3 Sales & Technical Support
Hotline. See the contact numbers at the end of this guide for the Extron office nearest you.
To take advantage of the various adjustments and test patterns available in the transmitter,
you need to connect a computer or other USB device to the front panel Configuration port
on either unit and operate using SIS commands (see Programming Guide, beginning on
the next page).
FOXBOX T HD-SDI Fiber Optic Transmitter • Programming Guide 10
Programming Guide
This section describes the remote operation of the FOXBOX T HD-SDI Transmitter via
Simple Instruction Set control, including:
• Configuration Port
• Host-to-Transmitter Communications
• Unit-initiated Messages
• Error Responses
• Timeout
• Using the Command and Response Table
Configuration Port
A connected computer can communicate with the transmitter via the front panel
Configuration port, a USB mini-B port (see item
A
, on page 8). A standard USB cable can
be used for remote control of the transmitter. The USB cable must be terminated on one
end with a USB mini-B male connector.
Host-to-Transmitter Communications
SIS commands consist of one or more characters per field. No special characters are
required to begin or end a command character sequence. When a command is valid, the
switcher executes the command and sends a response to the host device. All responses
from the switcher to the host end with a carriage return and a line feed (CR/LF =
]
), which
signals the end of the response character string. A string is one or more characters.
Unit-initiated Messages
When a local event, such as an equipment power-up, occurs, the unit responds by sending
a message to the host. The unit-initiated messages are listed below:
(c) Copyright 20yy, Extron Electronics FOXBOX T HD-SDI, Vx.xx, 60-xxx-xx
]]
The connected unit issues the appropriate copyright message (above) when it first powers
on. Vx.xx is the firmware version number; 60-xxx-xx is the part number of the connected
unit.
2Lnk
X1)
•Rte
X1!
•AudI
X1@
•T
]
The unit sends the status message whenever there is a change in input video, input audio,
or the fiber link.
X1)
,
X1!
, and
X1@
are defined starting on the next page.
FOXBOX T HD-SDI Fiber Optic Transmitter • Programming Guide 11
Error Responses
When the transmitter receives a valid SIS command, it executes the command and sends a
response to the host device. If the transmitter is unable to execute the command because
the command is invalid or it contains invalid parameters, the transmitter returns an error
response to the host. The error response codes are:
E10 — Invalid command
E13 — Invalid parameters
E14 — Not valid for this configuration
E17 — Invalid command for signal type
E22 — Busy
Timeout
Pauses of 10 seconds or longer between command ASCII characters result in a timeout.
The command operation is aborted with no other indication.
Using the Command and Response Table
The command and response table begins below. Symbols are used throughout the table
to represent variables in the command and response fields. Command and response
examples are shown throughout the table. The ASCII to HEX conversion table below is for
use with the command and response table.
ASCII to Hex Conversion Table
•
Space
Symbol Definitions
]
= Carriage return/line feed
}
= Carriage return (no line feed)
| = Pipe (can be used interchangeably with the
}
character)
• = space
E
= Escape key
W = Can be used interchangeably with the
E
character
X! = On and off, enable and disable status 0 = off or disable 2 = on or enable
X@ = Test pattern 0 = none 1 = color bars
X# = Audio input 0 = auto (default) 2 = analog
1 = 2-channel digital
X$ = AESC digital channel pair 1 (default) or 2
X% = AESG digital channel group 1 (default) or 2
X^ = Audio gain adjustment range 00 to 10
X& = Audio level adjustment range –18 to +10 (in 1.0 dB steps)
X* = Audio attenuation adjustment range 00 to 18
X( = Plus mode status 0 = disable Plus mode 1 = enable Plus mode (default)
X1) = Device name Up to 24 alphanumeric characters, plus minus sign (-). The last character cannot be a
minus sign.
X1! = Input status 0 = input not detected 1 = input detected
FOXBOX T HD-SDI Fiber Optic Transmitter • Programming Guide 12
X1@ = Input video format detected 0 = no signal
1 = SD 480i
2 = SD 576i
3 = HD-720p (50-60 Hz), 1080i (50-60 Hz), 1080p (23.98-30Hz),
2K (2048x1080p [23.98-30Hz])
4 = 3G-SDI-1080p (@50Hz, 59.94Hz, and 60Hz),
2k (2048x1080p@ 50, 59.94 Hz, and 60Hz)
5 = Unknown
X1# = Audio input selected 0 = no audio 1 = digital 2 = analog
X1$ = Firmware version v.vv
X1% = Build version v.vv
X1^ = Internal temperature nnnF•nnC
X1& = SFP module manufacturer Alphanumeric character string
X1* = Transmit or receive optical power Optical power in dBm
X1( = Operating temperature nnC
Command and Response Table for SIS Commands
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Loop-through video
mute
NOTE: These commands affect the output on the Loop-through port (see item
B
on page 4) only. The video transmitted to the
connected receiver is unaffected.
Mute output
2B Vmt2
]
Blank the Loop-through port video output.
Unmute output
0B
Vmt0
]
Output video on the Loop-through port.
Show video mute status
B
X!]
Video mute status is
X!
.
Test pattern
Output color bars
E
1TEST
}
Test1
]
Output the color bars test pattern.
Turn test pattern off
E
0TEST
}
Test0
]
Output the input video (no test pattern is
selected).
Show test pattern status
E
TEST
}
X@]
Audio input selection
Select audio input
E
I
X#
AFMT
}
AfmtI
X#]
Select the
X#
audio to output on
the fiber cable. In Auto, digital takes
priority over analog.
Show audio input
E
IAFMT
}
X#]
AES digital audio channel selection
NOTE: Eight-channel audio is divided into two groups, each
consisting of two channel pairs (four channels). The table at
right shows the channels contained within each group.
Group 1 Group 2
Ch Pair 1 Ch Pair 2 Ch Pair 1 Ch Pair 2
Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2
Select channel
EX$
AESC
}
Aesc
X$]
Select digital audio channel pair on
which audio will be embedded.
Show channel
E
AESC
}
X$]
AES digital audio group selection
Select group
EX%
AESG
}
Aesg
X%]
Select digital audio channel group on
which audio will be embedded.
Show group
E
AESG
}
X%]
NOTE:
X!
= Video mute status 0 = off (default) 2 = on
X@
= Test pattern 0 = none 1 = color bars on
X#
= Audio input 0 = auto (default) 2 = analog
1 = 2-channel digital
X$
= AESC digital channel pair 1 (default) or 2
X%
= AESG digital channel group 1 (default) or 2
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Extron FOXBOX T HD-SDI User manual

FOXBOX T HD-SDI
Extron
Brand
Extron
Model
FOXBOX T HD-SDI
Category
Network media converters
Type
User manual

Extron FOXBOX T HD-SDI is a fiber optic 3G/HD/SDI video transmitter that extends uncompressed digital SDI video signals up to 18.2 miles (29.3 km) over singlemode fiber using standard SFP modules, providing reliable signal transmission for broadcasting, post-production, and professional AV applications. It supports data rates up to 2.97 Gbps and resolutions up to 1080p60.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents