Thinklogical SDIXtreme 3G+ Dual Model Quick start guide

Thinklogical
Brand
Thinklogical
Model
SDIXtreme 3G+ Dual Model
Type
Quick start guide

Thinklogical SDIXtreme 3G+ Dual Model is a compact, broadcast-quality SDI over fiber extension system designed to transmit two 3G (2.97 Gb/s) or four SD (270 Mb/s)/HD (1.485 Gb/s) SDI signals with or without embedded audio and data over fiber optic cables. It supports both single-mode and multi-mode fibers, with a maximum transmission distance of 1000 meters for multi-mode and 40 kilometers for single-mode.

Thinklogical SDIXtreme 3G+ Dual Model is a compact, broadcast-quality SDI over fiber extension system designed to transmit two 3G (2.97 Gb/s) or four SD (270 Mb/s)/HD (1.485 Gb/s) SDI signals with or without embedded audio and data over fiber optic cables. It supports both single-mode and multi-mode fibers, with a maximum transmission distance of 1000 meters for multi-mode and 40 kilometers for single-mode.

IN
PWR
IN
3G SDI Fiber Optic Extension
TRANSMITTER SDI-L2M1X2-LCTX
SDIXtreme3G+
OUT
ACTIVE
SD
HD
3G
ACTIVE
SD
HD
3G
▼
▼
RS422
RS422
TX
TX
▼
▼
OUT
IN
MUX
LOOP OUT
COPY
OUT
OUT
PWR
OUT
OUT
3G SDI Fiber Optic Extension
RECEIVER SDI-C1M1X2-LCRX
SDIXtreme3G+
IN
ACTIVE
SD
HD
3G
SD
ACTIVE
SD
HD HD
3G 3G
▼
▼
RS422
RS422
RX
RX
▼
▼
IN
DE
MUX
COPY
SD
HD
3G
SDIXtreme
Dual Loop-Out 3G SDI Fiber Optic Extension
3G+
3G, SD, HD SDI Source 1
3G, SD, HD SDI
Loop Out 1
To Router’s UPSTREAM Receive Port
From Router’s DOWNSTREAM Transmit Port
SDIXtreme3G+_Dual_COPY_MUX_VX160_Quick_Start_Rev_A
Sources
Destinations
STEP 1: Connect your Fiber Optic Cables
from the SDIXtreme Receiver IN Ports to
any Router Transmit Ports. If using RS422,
a second, back-channel fiber is required at
the corresponding Router Receive Port. If
your application does not require a router,
connect directly to the Transmitter fiber ports.
STEP 5: Connect your Fiber Optic Cables
from the SDIXtreme Transmitter OUT
Ports to any Router Receive Ports. If
using RS422, a second, back-channel
fiber is required at the corresponding
Router Transmit Port. If your application
does not require a router, connect directly
to the Receiver fiber ports.
STEP 7: Connect your 3G or SD/HD SDI
video sources to the SDIXtreme
Transmitter’s IN Ports. If using RS422,
connect the devices’ RS422 ports to the
Transmitter’s RS422 Ports located directly
below the BNC ports.
STEP 9: Check that the 3G, SD or HD LEDs are illuminated
(depending on your signal type) on both the Transmitters and
the Receivers. These indicate that the connections are sound.
Ensure that all system functions are operating properly.
QUICK START GUIDE
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected] Visit us online at www.thinklogical.com for more product information, current literature and
the complete line of Thinklogical™ products.
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
3G+
3G+
Multi-Mode fiber can be up to 1000
meters in length. Single-Mode fiber
can be up to 40 kilometers.
3G+
STEP 3: Connect your 3G or SD/HD SDI destination
devices to the SDIXtreme Receiver’s OUT Ports.
3G+
STEP 2: Install the provided +5VDC power
supply to the SDIXtreme Receiver and plug it
into a standard AC source. Ensure that the
ACTIVE LED on the Receiver comes on. The
ACTIVE LED will blink if no SDI input is present.
3G+
To Router’s DOWNSTREAM Receive Port
From Router’s UPSTREAM Transmit Port
Source 3
Pan/Tilt/Zoom Controller
Source 1
Machine Controller
RS422
RS422
RS422
RS422
Source 1 3G, SD, HD SDI Outputs
Source 3 3G, SD, HD
SDI Output
3G, SD, HD SDI Source 3
2
1
3
3
4
4
5
6
8
3G, SD, HD SDI Source 2
7
7
7KVM Matrix Switch
VX160
router
STEP 4: If using RS422, connect your devices to
the Receiver’s RS422 ports located directly below
the BNC ports.
STEP 6: Install the provided
+5VDC power supply to the
SDIXtreme Transmitter
and plug it into a standard
AC source. Ensure that the
ACTIVE LED on the
Transmitter comes on. The
ACTIVE LED will blink if no
SDI input is present.
3G+
STEP 8: A Local Monitor or
other viewing device may be
connected to the Transmitter’s
LOOP OUT port.
The Logical Solution - Dual Serial Digital Interface Extension. The SDIXtreme product series is a compact, broadcast quality, SDI over fi ber extension system.
The dual system is designed to transmit up to two 3G (2.97 Gb/s) or four SD (270 Mb/s)/HD (1.485 Gb/s) SDI signals with or without embedded audio and data, and is
SMPTE 424M, 292M, 259M, 372M and 425 level A and B compliant. In addition, this fiber based transport system gives users the assurance that each signal is immune to
video pathological signals over the entire length of the fiber interconnect, while supporting all pathological patterns at all rates using standard SFPs. The system also
supports either single or multi-mode fiber and is fully compatible with Thinklogical’s VX and HDX Router line of products.
3G+
12 3 4
1 2 3 4 5
6 7
9
9
16 Rack Units, 850 Watts
12 3 4
1 2 3 4 56 7
Source 2 3G, SD, HD SDI Output
  • Page 1 1

Thinklogical SDIXtreme 3G+ Dual Model Quick start guide

Thinklogical
Brand
Thinklogical
Model
SDIXtreme 3G+ Dual Model
Type
Quick start guide

Thinklogical SDIXtreme 3G+ Dual Model is a compact, broadcast-quality SDI over fiber extension system designed to transmit two 3G (2.97 Gb/s) or four SD (270 Mb/s)/HD (1.485 Gb/s) SDI signals with or without embedded audio and data over fiber optic cables. It supports both single-mode and multi-mode fibers, with a maximum transmission distance of 1000 meters for multi-mode and 40 kilometers for single-mode.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents