CAME CP6099WL Installation guide

Brand: CAME

Model: CP6099WL

Category: Security access control systems

Type: Installation guide

FA00373-EN

BURGLAR ALARM

CONTROL UNIT

INSTALLER MANUAL

CP6099WL

ENGLISH

Page 2 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

INDICE

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . PAG. 3

SYMBOLS AND GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . 3

DESCRIPTION OF USE . . . . . . . . . . . . . . . . . . . . . . . . . . 3

SECURITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

EN 50131 STANDARD - SPECIFIC RECOMMENDATIONS . . . . . . . . . 3

INSTALLING THE SYSTEM . . . . . . . . . . . . . . . . . . . PAG. 4

GENERAL SYSTEM DIAGRAM . . . . . . . . . . . . . . . . . . . . . . 4

RS-485 BUS WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . 5

APPLICATION NOTES REGARDING WIRING THE RS-485 BUS . . . . . . . . . . .5

CHOOSING THE CROSS-SECTION OF THE RS-485 BUS CABLE. . . . . . . . . .5

TRADITIONAL WIRING (in - out) . . . . . . . . . . . . . . . . . . . . . . . . . 6

DOUBLE BRANCH WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

WIRING WITH BRANCHING. . . . . . . . . . . . . . . . . . . . . . . . . . . .6

WIRING WITH BUS AMPLIFIER . . . . . . . . . . . . . . . . . . . . . . . . . .7

INSTALLING THE CONTROL UNIT. . . . . . . . . . . . . . . . PAG. 8

TECHNICAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . 8

MAIN CONTROL UNIT COMPONENTS . . . . . . . . . . . . . . . . . . 8

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SECURING TO THE WALL . . . . . . . . . . . . . . . . . . . . . . . .10

POWERING THE CONTROL UNIT . . . . . . . . . . . . . . . . . . . . .10

230 V AC mains power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

WIRING THE OUTPUTS. . . . . . . . . . . . . . . . . . . . . . . . . .10

PROGRAMMABLE OUTPUT U1. . . . . . . . . . . . . . . . . . . . . . . . . 10

PROGRAMMABLE OUTPUT U2, U3, U4 (Open Collector) . . . . . . . . . . . . 10

GENERAL ALARM RELAY OUTPUTS . . . . . . . . . . . . . . . . . . . . . . 11

PSTN TELEPHONE LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

WIRING THE INPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . .11

STLCDS - STDCSB - STDCSN KEYPADS . . . . . . . . . . . . PAG. 12

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

KEYPAD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

SYSTEM STATUS ALERTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SYSTEM STATUS ALWAYS DISPLAYED . . . . . . . . . . . . . . . . . . . . . 13

DISPLAY ICONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ALPHANUMERIC KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

KEYPAD MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SINTS READER AND SKEYT KEY . . . . . . . . . . . . . . . . PAG. 14

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

DISPLAYING THE SYSTEM STATUS. . . . . . . . . . . . . . . . . . . . . . . 15

SRX128D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ADDRESSING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . PAG. 16

SIGSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SSIP/SIFLAN LAN INTERFACES . . . . . . . . . . . . . . . . . . . . .16

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

SIFCPKNX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

001SIGPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

BOARD DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LED STATUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

INSERTING THE SIM CARD . . . . . . . . . . . . . . . . . . . . . . . . . . 18

INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MANUAL FIRMWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . 18

MANAGING THE CONTROL

UNIT USING THE CAME MOBILE APP. . . . . . . . . . . . . . PAG. 19

CONFIGURING CONNECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . 19

CAMECONNECT . . . . . . . . . . . . . . . . . . . . . . . . PAG. 21

VIDEO VERIFICATION . . . . . . . . . . . . . . . . . . . . . . PAG. 21

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

DESCRIPTION OF THE SYSTEM COMPONENTS . . . . . . . . . . . . . . . . 21

SERVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

SYSTEM STARTUP . . . . . . . . . . . . . . . . . . . . . . . PAG. 23

PRELIMINARY INFORMATION . . . . . . . . . . . . . . . . . . . . . .23

ACCESSING THE TECHNICAL MENU . . . . . . . . . . . . . . . . . . . . . . 23

CHOOSING NUMBERS ABOVE 9 . . . . . . . . . . . . . . . . . . . . . . . . 23

OPENING/CLOSING THE CONTROL UNIT . . . . . . . . . . . . . . . . . . . . 23

SYSTEM MAINTENANCE/SERVICING . . . . . . . . . . . . . . . . . . . . . . 23

SWITCHING ON FOR THE FIRST TIME . . . . . . . . . . . . . . . . . .24

POWERING ON THE CONTROL UNIT . . . . . . . . . . . . . . . . . . . . . . 24

SELF-LEARNING MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

ADDRESSING AND LEARNING PERIPHERAL DEVICES . . . . . . . . . .25

ACQUIRING KEYPADS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

ACQUIRING READERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

ACQUIRING RADIO RECEIVER MODULES ON THE BUS . . . . . . . . . . . . . 26

TOUCH SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

DEFINING SYSTEM AREAS. . . . . . . . . . . . . . . . . . . . . . . .27

PROGRAMMING SCENARIOS . . . . . . . . . . . . . . . . . . . . . .27

CREATING SCENARIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

ASSOCIATING SCENARIOS WITH KEYPADS. . . . . . . . . . . . . . . . . . . 28

ASSOCIATING SCENARIOS WITH READERS . . . . . . . . . . . . . . . . . . 29

PROGRAMMING INPUTS. . . . . . . . . . . . . . . . . . . . . . . . .30

LEARNING RADIO INPUTS . . . . . . . . . . . . . . . . . . . . . . . .31

PROGRAMMING OUTPUTS. . . . . . . . . . . . . . . . . . . . . . . .31

PROGRAMMING TELEPHONE CALLS AND SMSS . . . . . . . . . . . . .31

SETTING PSTN - GSM PRIORITIES . . . . . . . . . . . . . . . . . . . . . . . 31

SETTING TELEPHONE NUMBERS . . . . . . . . . . . . . . . . . . . . . . . 32

RECORDING VOICE MESSAGES FROM PC . . . . . . . . . . . . . . . . . . . 35

SENDING VOICE MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CREATING USER CODES. . . . . . . . . . . . . . . . . . . . . . . . .35

ENABLING/DISABLING A CODE . . . . . . . . . . . . . . . . . . . . . . . . 36

ACQUIRING KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

LEARNING TRANSMITTERS . . . . . . . . . . . . . . . . . . . . . . .37

SYSTEM TEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

CONNECTING A PC TO THE CONTROL UNIT . . . . . . . . . . PAG. 38

LOCAL PROGRAMMING VIA USB. . . . . . . . . . . . . . . . . . . . .38

RESETTING THE SYSTEM. . . . . . . . . . . . . . . . . . . . PAG. 39

RESETTING CODES . . . . . . . . . . . . . . . . . . . . . . . . . . .39

DEFAULT PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . .39

DEFAULT PARAMETERS VIA DIP SWITCH. . . . . . . . . . . . . . . . .39

ENGLISH

Page 3 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

General information

Symbols and glossary

This symbol indicates parts about safety.

This symbol indicates parts to read carefully.

Light signal on and steady.

Light signal off.

Light signal flashing.

INSTALLER: the person/company responsible for the design, con-

struction and programming of the burglar alarm system.

USER: the person(s) using the burglar alarm system.

Description of use

The CP6099WL burglar alarm control unit is designed to increase

security in residential and service environments, even in places

where a wired system would be particularly difficult to install.

Any installation and operation that differs from what is set

out in this manual is prohibited.

Security

If properly designed, the burglar alarm system guarantees a high

level of security for the environments it is protecting and the users

that are using it.

To ensure this, we need to follow certain rules:

Installation must be carried out by qualified and experienced

personnel in compliance with applicable regulations.

Check the main power connections and relative earth con-

nections.

Once system startup is complete, make sure that the user has

changed the default user code (123456).

EN 50131 STANDARD - SPECIFIC RECOMMENDATIONS

To ensure the system complies with the EN 50131 standard, it

is very important to follow the recommendations below:

••the sound signals (buzzers) from the readers cannot be disa-

bled;

••the “Memory” type input must not be used;

••the inputs configured as “Arming” are only suitable if they are

commanded by devices with more than 10,000 combinations;

••the fault signalling of the devices connected to the system is

not required by the standard, but if a device is equipped with this

signal, this must be connected to the input defined as faulty in the

control unit;

••the telephone dialler must be active;

••an external self-powered siren must be present in the system

to signal that the burglar alarm has been triggered;

••the command to force arming of areas with open inputs must

not be armed;

••the number of alarms for self-exclusion of an input must be

set between 3 and 10;

••the no mains signal time must be set to 1 minute;

••the battery test time must be set to more than 5 minutes;

••quick arming must not be enabled;

••the option to stop communication once the control unit is

switched off must not be enabled;

••the Input 1 and Input 2 times can be set to a maximum of 45

seconds;

••the system masking time must be set to ≤ 30 seconds;

••the pre-arming test must be enabled.

4,7 kohm

ENGLISH

Page 4 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Installing the system

General system diagram

GSM

Antenna

SIGSM

SSIP/SIFLAN SIFCPKNX

SIGPRS

SIFTS01

Touch

screen

Touch

screen

PC-Control Unit

connection via USB

Telephone

PSTN

Telephone line

Self-powered

siren

Siren

Single balancing

input

NC input

230 V AC

power supply

Bus branch

󰽤

󰽥

ENGLISH

Page 5 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Above 12 V DC

YES

Always wire the bus in “in and out” mode. Do not wire the bus in a

star configuration.

If you need this configuration, follow the instructions given in this

chapter.

In the case of long bus stretches, always install 150 ohm resistors

between terminals A and B of both bus heads.

The maximum cable length (maximum 800 m stretches) and the

cross-section of the core depend on the number of modules and

the overall current draw on the various bus stretches. As the cur-

rent draw increases, so does the voltage drop on the cables and the

supply voltage to the devices on the bus decreases.

The voltage at all the + and - terminals of the bus devices (keypads,

readers, modules...) should not be less than 12 V DC.

If it is less, add an auxiliary power supply, disconnecting the positive

and keeping the negative common.

RS-485 bus wiring

APPLICATION NOTES REGARDING WIRING THE RS-485 BUS

The wiring on the bus connecting the control unit to the readers,

keypads and amplifiers must follow the rules dictated by the RS-

485.

Use shielded twisted cables only, with a cross-section of at least:

󰽤 2x0.5 mm² for the power supply and 2x0.22mm² twist-

ed for data.

󰽥 2x0.5 mm² for the power supply and 2x2x0.22mm²

twisted for data (use to create branches).

The braid must be continuous and connected to the negative (-)

terminal on the control unit.

CHOOSING THE CROSS-SECTION OF THE RS-485 BUS CABLE

The recommended cable for the RS-485 bus is:

• Twisted and shielded cable - grade 4 (600/1000 V).

• One twisted pair for data - cross-section 2x0.22 mm².

• One pair for power supply - cross-section 2x0.5 mm²

or higher depending on the distances and currents (see

table below).

Please find a table below to help you calculate the cross-section of

the power cables as the distance and current draw vary.

MAXIMUM LENGTH

OF THE RS-485

CABLE

CURRENT DRAW

0.1 A 0.25 A 0.5 A 1 A

CROSS-

SECTION

0.5 mm2 175 m 70 m 35 m 17 m

0.75 mm2 262 m 105 m 52 m 26 m

1 mm2 350 m 140 m 70 m 35 m

1.5 mm2 525 m 210 m 105 m 52 m

The supply voltage drop should not exceed 1.4 V (voltage

measured on the power supply terminals and the terminals on the

bus device that is furthest away).

If a cable with a suitable cross-section is not available, the use

of additional auxiliary power supplies should be taken into

consideration.

Example: Let’s assume we have connected the following at a

distance of 200 m:

∙A STDCSB keypad (maximum current draw 60 mA)

∙A SINTS transponder reader (maximum current draw 100 mA)

∙A SRX128D radio expansion module (maximum current draw

100 mA)

Having a maximum current draw of 260 mA, in this case, the

alternatives are to use a cable with a cross-section of 1.5 mm²

or a cable with a cross-section of 0.5 mm² and an auxiliary power

supply connected at the end of the line as shown below:

ENGLISH

Page 6 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

WIRING WITH BRANCHING

The branching consists of a cable with 3 pairs of which 2

are twisted (each pair is composed of cores A and B). Analysing the

circuit thus produced, we note that the structure of the RS-485 bus

continues to be linear (in-out).

DOUBLE BRANCH WIRING

RS-485 CABLE

Shielded 2x1.5mm² + 2x0.22mm² twisted

Control unit Device on bus

RS-485 CABLE

Shielded 2x0.5mm² + 2x0.22mm² twisted

Control unit Auxiliary

power supply Device on bus

If the remote devices have been installed correctly, all the

BUS communication LEDs on each device will flash. If some do

not flash, this means that the device has not been installed and

programmed correctly (check control unit wiring, addressing and

programming).

TRADITIONAL WIRING (in - out)

ENGLISH

Page 7 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

WIRING WITH BUS AMPLIFIER

Bus amplifier

SRS485

SRX128D

󰒄

󰒅

󰒉

󰒆

󰒊

󰒇

󰒋

󰒈

󰒌

󰒍

󰒎

󰒏

ENGLISH

Page 8 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Installing the control unit

Technical features

1. 230 V AC mains connection terminals.

Be careful, live parts.

2. Battery connection cables.

Respect the polarity (red = +, black = -)

3. Control unit tamper

4. Mains fuse. Glass fuse, T, 315 mA, plus PTC thermal protector

in the transformer at 120 ° C.

5. Microphone and speaker

6. Battery restraint

7. Acoustic warning device

8. 868 MHz antenna

9. 433 MHz antenna

10. Spirit level for adjusting the tilt

11. Transformer

12. Keypad with graphic display - 160x32 pixels

Main control unit components

Supply voltage 230V AC 50Hz –15% + 10%

Transformer 17 VA

Maximum power supply

delivery 400 mA

Battery 12 V - 2.2 Ah

Operating temperature 0° - 40°C

Relative humidity 25% - 75% non-condensing

Maximum safety rating 2

Environmental class II

Insulation class

Dimensions (HxLxD) 300x250x65 mm

Container ABS RAL9003

IP IP30

Weight 2.7 kg

Areas

Scenarios

Radio inputs

Wired inputs in control unit

Type of inputs in control unit

NC, NO; SB, DB, PC

Relay outputs on board

Open collector outputs

programmable on the control

unit

Radio concentrator modules

on bus

1 built-in + 2 optional on bus

Transponder readers

1 built-in + 2 optional on bus

Keypads

1 built-in + 2 optional on bus

Radio receivers

1 built-in + 2 optional on bus

Touchscreen

Yes

Acoustic warning device

Built-in

Transponder keys

Installer codes

User codes

Transmitters

Programmable timer

20 daily operations

Events

999

485 BUS

PSTN dialler

Built-in

GSM dialler

Optional

Voice synthesis

Built-in

Audio

Built-in microphone and

speakers for recording and

playback of messages

Telephone numbers

8+1

CONTACT-ID

Yes

FW can be reprogrammed from

control unit Yes

LAN interface

Optional

USB communication port

Built-in

Control via SMS

Yes (with GSM)

Control via VOICE

Yes

LAN Remote Programming and

Assistance Yes (with LAN interface)

PSTN Remote Programming

and Assistance Yes

GSM Remote Programming and

Assistance

Yes (with GSM)

RTC + backup battery

Yes

󰒄

󰒋

󰒌

󰒏

󰒕

󰒎

󰒔

󰒈

󰒅

󰒒

󰒆

󰒇

󰒍

󰒉

󰒓

󰒊

󰒐

󰒑

ENGLISH

Page 9 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Board description

RS-485 bus terminals for connecting keypads, radio

concentrators and readers:

[+,-] bus power supply;

[A,B] data;

[F6] self-resetting fuse - 1.35 A.

Control unit input terminals - can be NO, NC, SB, DB, PC.

[+,-] power supply;

[1,2,3,4,5,6] inputs (the reference is to negative);

[F3] self-resetting fuse - 1.35 A.

Control unit output terminals:

[AUX +, -] output power supply available protected by F5

self-resetting fuse;

[U1] output programmable to positive protected by 100

ohm resistor (ON=13.8 V DC, OFF=NO);

[U2,U3,U4] open collector output programmable to negative

protected by 100 ohm resistor (ON=0 V DC,

OFF=NO);

[NO, C, NC] general alarm relay with dry contacts;

[F5] self-resetting fuse - 1.35 A.

A short circuit with the open collector output active for

an extended time may lead to the breakage of the protection

resistor.

[JP3] jumper to enable/disable the anti-opening tamper

(position C to disable it, position O to enable it).

[JP4] jumper to enable/disable the tear-resistant tamper

(position C to disable it, position O to enable it).

5[SW2] Control unit anti-opening slide tamper.

6[SW3] Control unit anti-opening slide tamper.

7[CN2] Connector for GSM module.

[F4] self-resetting fuse - 1.35 A.

Board description

CURRENT DRAW AND BATTERY LIFE OF CP6099WL POWERED

BY 12 V DC BATTERY 2.2Ah

Current draw with control unit

in standby without accesso-

ries and peripheral devices

connected

• 95 mA with keypad backlight

off

• 110 mA with keypad back-

light on at maximum intensity

Current draw with control

unit in alarm mode and PSTN

calling

155 mA

Current draw with control unit

in alarm mode and GSM calling 230 mA

Board description

Dip1 is used to switch the control unit from service to

maintenance (ON= Maintenance, OFF= Service).

Dip2 is used to restore the default settings for the

codes.

Dip3 is used to reset the default parameters

(parameters + codes + keys).

Dip4 is used to reprogram the control unit firmware.

9[P1] button to reboot the control unit (does not reset

parameters; does not alter the configuration).

PE] earthing terminal.

[L, L] external PSTN telephone line input terminals.

[T, T] PSTN telephone line output terminals to telephone or

control unit.

[CN1] connector for connecting to the Ethernet interface or the

touchscreen via the SIFTS01 interface.

[F4] self-resetting fuse - 1.35 A.

12 [CN9] USB socket for connection to the PC (with A-B USB

cable).

13 [F8] glass fuse, T, 3.15 A.

14 [V AC] 230 V AC mains connection terminals.

15 [CN7] battery connector.

[F2] self-resetting fuse - 1.6 A.

16 [CN13] connector for connecting the control unit base board to

the keypad board.

17 [CN3] connector for connecting the control unit base board to

the audio board.

18 Radio indicator LED

CURRENT DRAW AND BATTERY LIFE OF CP6099WL POWERED

BY 12 V DC BATTERY 2.2Ah

Battery life* with control unit

in standby without accesso-

ries and peripheral devices

connected

Minimum 15 hours

*CAUTION: The battery life decreases depending on the number

of alarms and/or telephone calls and/or manoeuvres performed,

and depending on the number of accessories/peripheral devices

connected

250

300

197 2578

125125

+ - TC TAMPER ALARM

5 6

󰒅

󰒄

ENGLISH

Page 10 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

• After disconnecting the mains power supply, remove the Plex-

iglas protection on the terminal block by unscrewing the two

screws attached to the transformer 󰒄.

• Connect the 230 V AC Line and Neutral cable to the terminal

block terminals (the power supply cables must enter the pre-

drilled hole󰒅)

• Replace the Plexiglas protection on the terminal block, secur-

ing it to the transformer with the two screws.

U1 is an output (freely-programmable) which provides a positive

when active:

• U1 ON = 13.8 V DC

• U1 OFF = not connected

The default programming is TC for the inhibition of the microwave

with the system is off (U1 = OFF if at least one area is on or in exit

time; U1 = ON if the system is completely off).

The output is protected by a 100 ohm resistor.

It can also be used to command sirens or other loads.

PROGRAMMABLE OUTPUT U2, U3, U4 (Open Collector)

A short circuit to 12 V DC with the output active for an extended

time may lead to the breakage of the protection resistor.

Non-self-powered siren

U2, U3, U4 are open collector outputs (freely-programmable) that

provide a negative when they are active:

• U2, U3, U4 ON = 0 V DC

• U2, U3, U4 OFF = not connected

The outputs are protected by 100 ohm resistors.

Wiring the outputs

PROGRAMMABLE OUTPUT U1

A short circuit to earth with the output active for an extended

time may lead to the breakage of the protection resistor.

Securing to the wall

Install the control unit away from access points and points that are

difficult to identify.

Secure to a suitable wall that can support the control unit over time.

Make the holes and channel to pass the cables through before in-

stallation.

Use the 2 prepared holes for securing to the wall.

Powering the control unit

230 V AC mains power

Provide a suitable dual-pole disconnection device (circuit

breaker), with a maximum of 3 mm between the contacts, to

disconnect the power supply.

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

4,7 KOHM

+ - TC

TAMPER ALARM

ENGLISH

Page 11 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

If you want to control a relay with an open collector output (or relay

output), it is necessary to add a diode (1N4007) in parallel with the

relay coil.

GENERAL ALARM RELAY OUTPUTS

The RELAY 1 output is a general alarm output and is not

programmable. It follows the general alarm status and remains

active for the programmed time.

Non-self-powered siren

Self-powered siren

PSTN TELEPHONE LINE

The PSTN telephone line must be connected to the [L, L] terminals

and in output to the [T, T] terminals for switchboards or telephones.

“Simulated” telephone lines (lines coming out from

ADSL routers) can cause disturbances to CONTACT-ID digital

communications to the security companies.

Wiring the inputs

Balances are made using 4.7 kohm resistors at 5%.

Yellow 4

Purple 7

Red 100

Gold 5%

NORMALLY OPEN (NO)

NORMALLY CLOSED (NC)

SINGLE BALANCING (SB)

PULSE COUNT OR INERTIAL (PC)

The U1 output provides a positive with an active output (ON = 13.8

V DC). By default, the U1 output is programmed as TC (output active

when the system is off and active during the exit time and when at

least one area is armed).

DOUBLE BALANCING (DB)

DOUBLE BALANCING SENSOR (DB)

DOUBLE BALANCING SENSOR (DB) WITH MICROWAVE

BLOCK WITH CONTROL UNIT OFF (TC)

󰽤





󱎵 ➡

08:24 19/03/13

#####UUUPX---

08:24 19/03/13

#####UUUPX---

ENGLISH

Page 12 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

STLCDS - STDCSB - STDCSN keypads

BOARD DESCRIPTION

1. RS-485 bus terminals for connecting keypads and readers:

[+,-] bus power supply;

[A,B] data.

2. [SW1] Anti-opening and tear-resistant tamper.

3. [JP1] Jumper to enable/disable the tamper, see 󰽤

4. Red bus communication alert LED. If this flashes, it

means that the keypad is communicating with the control

unit.

5. Keypad buzzer.

keypads connected on the bus and the local keypad built into the

control unit.

KEYPAD DISPLAY

The display consists of two lines of 16 graphic characters. At rest,

the keypad goes into “Power saving” mode, decreasing the light

intensity after a set time.

On some models of keypad, below the display, there are 16 num-

bers that facilitate the interpretation of the second line of the dis-

play, with the following key:

# = area armed;

U = area being armed (exit time countdown under way);

X = area being armed but not ready for arming due to the present

of open inputs;

P = area partially armed (there is at least one input associated with

the area that is temporarily excluded);

R = area in active patrol mode;

N = disarmed area that is not ready;

- = area off;

= area not managed by the keypad.

Example: reading the display 󱎵 showing:

• Areas managed: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13.

• Areas not managed: 14, 15, 16.

• Areas armed: 1, 2, 3, 4, 5.

• Areas being armed: 6, 7, 8.

INSTALLATION

The keypads must be wall-mounted in sheltered environments,

raised or recessed with the 001DC00VISIO01 box (only

STDCSN/STDCSB).

Connect the control unit and keypads on the respective terminals

[+ A B -].

ADDRESSING

The keypad address is assigned by the control unit during ad-

dressing.

User interface

Subsequent descriptions apply to both STDCSN/STDCSB/STLCDS

“Flat” capacitive keypads in black (STDCSN) or white (STDCSB) or

with hatch (STLCDS) which can be connected to the bus. Can be

wall-mounted or recessed.

Blue backlit LCD, touch-sensitive keys (STDCSN/STDCSB) or mem-

brane keys (STLCDS).

STDCSN

STDCSB

STLCDS

Tamper ON Tamper OFF

STLCDS

ENGLISH

Page 13 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

DISPLAY ICONS

Icon Meaning

CAME logo

System armed

System disarmed

System partially armed

Programming

Event log

User menu

Alarm log

Not ready for arming

Generic power failure

230 V mains power failure

Battery failure

PSTN line fault

GSM line fault

Serial connection (local)

Ethernet connection (remote)

ALPHANUMERIC KEYPAD

Keys Functions

The alphanumeric keys allow users to enter codes,

select the areas being armed and edit the param-

eters.

Menu navigation and selection keys.

Parameter editing keys.

After entering the code, users gain access to the

User Menu. If pressed for more than 5 seconds, it

allows access to the keypad menu.

Scenario launch keys.

System shutdown key.

KEYPAD MENU

The Keypad Menu is independent from the control unit menu and

allows users to set various keypad characteristics such as the lan-

guage, the contrast and brightness of the display, the illumination

of the keys and the system status LEDs, and other functions as

shown in the table below.

To enter the Keypad Menu, press and hold for a few seconds,

until the Keypad <|> language screen appears on the display. Then use

the keys to navigate and select as shown.

Keypad <|> cleaning enables users to clean the keypad safely. Entering

the values with 󰯯, a 30-second countdown begins, during which

the keypad is not active. At the end, it automatically returns to the

menu.

• Areas partially armed: 9.

• Areas not ready: 10.

• Areas off: 10, 11, 12, 13.

SYSTEM STATUS ALERTS

The system status alerts behave according to installer program-

ming.

Depending on installer programming, the display can be kept al-

ways visible (LEDs and display visible) or masked for improved

safety (no system status information given to unauthorised per-

sons). Only the alarm LEDs (RED for the readers and YELLOW for

the keypads) remain visible if activated.

Following the activation of a scenario or any other system manage-

ment activity, after a programmed time (30 seconds max.), all the

other LED and display alerts are interrupted and the LEDs go off.

SYSTEM STATUS ALWAYS DISPLAYED

LED

(colour) Status Meaning

(green)

〇Indicates that there are open inputs. If a sce-

nario is launched, an alarm may be generated.

Check the inputs open when the scenario is

launched.

●Indicates that there are NO open inputs. The

system can be turned on without problems.

(green)

〇Indicates that the managed areas are off (sys-

tem off).

●Indicates that all the managed areas are on

(system fully on).

◉Indicates that at least one managed area is on

(system partially on).

(red)

〇Indicates that the managed areas are NOT in

alarm mode.

●Indicates that at least one managed area is in

alarm mode (system in alarm mode).

◉Indicates that the associated system has de-

tected an alarm that has been muted. See the

event list for the alarm log.

(yellow)

〇Indicates that there are no faults on the system.

●Indicates that there is a fault.

When the ‘Status masking’ function is active, this

indicates the presence of an event to display.

It may indicate that: the mains power supply

(230 V AC) is absent; the battery of a radio pe-

ripheral device needs to be replaced; a fuse

needs to be replaced; a fault input is unbal-

anced; the clock has not been initialised; there

is a problem on the PSTN or GSM line; the GSM

module SIM has expired.

◉Indicates that the control unit battery needs to

be replaced

〇 = Off | ● = On | ◉ = Flashing

The reporting of events that occur at the same time follows

the following priority: alarms, exit times, faults. The on-screen dis-

play occurs cyclically.

󰒄

②

①

③

④

ENGLISH

Page 14 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Keypad <|> version allows users to view the software version of the

keypad only.

Press [#] twice in a row to exit the Keypad Menu. After 60 seconds

have passed with no operation, the keypad automatically exits the

Keypad Menu.

The LEARNING menu is only available on radio keypads.

MENU HEADINGS VALUES











Keypad

language

󰯯 -> 󰯲 ITALIANO / ENGLISH /

FRANÇAIS / ESPAÑOL /

PORTUGUÊS 󰯰

<- 











Keypad

version

󰯯 -> 󰯲 CAME

v. 1.01 󰯰

<- 











Learning

No. 02 SN00000021

󰯯 -> 󰯲 LEARNING

N.--XXXXXXX 󰯰

<- 











Keypad

cleaning

󰯯 -> 󰯲 Keypad cleaning

30 s 󰯰

<- 











Tamper 󰯯 -> 󰯲 Tamper

disabled/enabled 󰯰

<- 











Buzzer 󰯯 -> 󰯲 Buzzer

disabled/enabled 󰯰

<- 











Display ON

time

󰯯 -> 󰯲 Dis time ON

10 s 󰯰

<- 











Min status

LED brightness

󰯯 -> 󰯲 MIN. LED BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 

MENU HEADINGS VALUES











Max status

LED brightness

󰯯 -> 󰯲 MAX. LED BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 











Min keypad

brightness

󰯯 -> 󰯲 MIN. KEYP. BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 











Max keypad

brightness

󰯯 -> 󰯲 MAX. KEYP. BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 











Min display

brightness

󰯯 -> 󰯲 MIN. DIS. BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 

Max display

brightness

󰯯 -> 󰯲 MAX. DIS. BRIGHTN.

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 











Display

contrast

󰯯 -> 󰯲 DIS. CONTRAST

▌▌▌▌▌━ ━ ━ ━ ━󰯰

<- 











To enter the Keypad Menu, press and hold for a few seconds,

until the KEYPAD LANGUAGE screen appears on the display. Then use

the keys to navigate and select as shown.

KEYPAD CLEANING enables users to clean the keypad safely. Entering

the values with 󰯯, a 30-second countdown begins, during which

the keypad is not active. At the end, it automatically returns to the

menu.

KEYPAD VERSION allows users to view the software version of the key-

pad only.

Press [#] twice in a row to exit the Keypad Menu. After XX seconds

have passed with no operation, the keypad enters STANDBY mode

and after a further xx seconds, it automatically exits the Keypad

Menu.

BOARD DESCRIPTION

SINTS reader and SKEYT key

󰒄- WIRING SERIES HOLE COVER CAP

󰒅- TRANSPONDER READER

󰒆- INDICATOR LED

󰒇- KEY-SENSITIVE AREA

RS-485 bus terminals for connecting keypads and readers:

[+,-] bus power supply;

[A,B] data.

PRE ENTER TEST

has been enabled in the technical menu in

SPECIAL FUNCTIONS

, in the event of existing system anomalies (e.g. no

phone line, no communication with at least one system device etc.)

scenario startup via the reader will be disabled (the reader will emit

a beep, cancelling the operation).

The SINTS reader is a transponder reader for SKEYT keys, which

can be used to manage alarm system arming/disarming, using up

to 3 adjustable scenarios.

The key is used to manage the system via the reader. It contains

no batteries and must first be acquired by the control unit in order

to operate.

Each key is recognised uniquely within the control unit and the

event log.

ENGLISH

Page 15 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

INSTALLATION

The connector occupies just one module in the switchboxes of any

residential-use system.

Connect the control unit and readers on the respective terminals

[+ A B -].

For addressing and acquiring the readers and keys, see the relevant

chapters.

The readers must be installed in an area protected from break-

ins or in a guarded area of the system, otherwise the reference

standard is voided.

DISPLAYING THE SYSTEM STATUS

LED Meaning

Indicates that scenario 1 is not active.

Indicates that scenario 1 is active.

during the exit time, it indicates that there is at

least one scenario 1 input open.

when the system is off, it shows whether there

are open inputs belonging to the areas managed

by the reader.

Indicates that scenario 2 is not active.

Indicates that scenario 2 is active.

during the exit time, it indicates that there is at

least one scenario 2 input open.

when the system is off, it shows whether there

are open inputs belonging to the areas managed

by the reader.

Indicates that scenario 3 is not active.

Indicates that scenario 3 is active.

during the exit time, it indicates that there is at

least one scenario 3 input open.

when the system is off, it shows whether there

are open inputs belonging to the areas managed

by the reader.

Indicates that the associated areas are off (sys-

tem off).

Indicates that at least one associated area is on

(system on or partially on).

Slow flashing to indicate that the system is on

and has detected an alarm.

Quick flashing to indicate that the system is off

and is in alarm log mode.

See the event list for the alarm log. To remove

the alert, see the system management chapter.

off, on steady, on flashing ( •quick, slow)

With the transponder reader, you can view the system status

through the alerts given by its LEDs, as shown in the table above.

Depending on programming, the display can be kept always visible

(LEDs on steady or flashing) or masked for improved safety (no

system status information given to unauthorised persons). The LED

alerts are only visible following the activation of a scenario or any

other system management activity, after a programmed time (30

seconds max.), they are interrupted and the LEDs go off. Only the

red alarm LED (LED 4) remains visible when activated.

SRX128D

Receiver to for two-way communication with all the radio devices

connected and addressed in the control unit.

BOARD DESCRIPTION

1. RS-485 bus terminals for connecting keypads and readers:

[+,-] bus power supply.

[A,B] data.

2. [BUS] red bus communication alert LED. If flashing, this

means that the module is communicating with the control unit.

3. [ERR] red radio communication LED indicating incorrect

receipt or peripheral device not associated.

4. [OK] green radio communication LED indicating correct

receipt.

5. Green LEDs indicating the intensity of the signal received. A

signal received correctly consists of at least 3 bars.

6. [SW1] 8 dip switches for:

[1..4] setting the module address;

[5] activating the LEDs (ON active);

[6,7] not used;

[8] disabling the tear resistant tamper (ON disabled).

7. [R] Button to reboot the receiver (e.g. after an address

change).

8. [M] Button not used.

9. [SW2] Anti-opening tamper.

10. [SW3] Tear-resistant tamper.

INSTALLATION

The receiver must been installed in a sheltered place and in the

best position to receive the radio signal from the various connected

devices.

Connect the control unit and receiver on the respective terminals

[+ A B -].

ADDRESSING

The local radio module address is 01, therefore the address 02 or

03 can be set for the modules connected on the bus.

C.U. ADDRESS

0 Invalid

1 Invalid

󰒆

󰒇

󰒅

󰒄

󰒉

󰒊

󰒈

󰒊

󰒅

󰒆

󰒄

󰒇

ENGLISH

Page 16 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Accessories

SIGSM

Telephone dialler suitable for all CP control units, complete with

whip antenna. It allows users to send SMSs and voice messages

as well as receive SMSs and DTMF commands for remote control.

BOARD DESCRIPTION

terminal block, then connect it to the SIGSM interface 󰒆 and se-

cure the latter with the three turrets 󰒇 supplied to the control unit

board 󰒈.

Connect SIGSM from connector 󰒊 to connector CN2 󰒋 on the

control unit board.

Power the control unit and, after a minute, check that the green

LED DL1 󰒉 on SIGSM indicates the SIM has been registered cor-

rectly, flashing slowly .

SSIP/SIFLAN LAN INTERFACES

The SSIP interface enables the user to program, read the

configuration and display the status of the control unit from a PC

using the SWLINK program.

In addition to offering the same functions as the SIFLAN interface,

the SSIP interface also enables the user to control the unit using a

keypad simulated by a web page.

For remote connection to the SSIP and SIFLAN interfaces,

it is necessary to configure the router connected to the domestic

network (see relative instruction manual).

BOARD DESCRIPTION

Attach the interface card 󰒄 to the four turrets 󰒅 positioned on the

Plexiglas bracket 󰒆 already installed in the control unit board 󰒇.

In order to configure the devices, see the relative instruction

manuals.

5. Terminal block for connection

to the master touchscreen (for

SIFLAN only)

6. LAN connection

7. Connector for connecting to the

control unit

8. Button to reset to default

9. Communication type selection

(for SSIP only, default A)

In order for the control unit to operate correctly, the jumpers

[JP1] - [JP2] pos. 󰒈 on SSIP must stay in position A.

The monochromatic touchscreen must be connected to the alarm

control unit using the LAN interface. This is only possible with

SIFLAN using terminal block 1.

INSTALLATION

All operations to enable and disable the board must be carried

out while the control unit is not powered.

1. Connector for connecting to the control unit board.

2. SIM slot.

3. [DL1] Green LED indicating GSM operation:

GSM module off or not present.

Active GSM call (incoming or outgoing).

GSM dialler not registered in the GSM network.

GSM dialler registered correctly in the GSM network.

4. Connector for GSM antenna.

INSTALLATION

All operations to enable and disable the interface must be car-

ried out while the control unit is not powered.

Secure the antenna 󰒄 to the Plexiglas protection 󰒅 covering the

+TX RX –

CN2

KNX PROG

–

BUS

KNX

CN1

BUS





 

SIM900

+ RX TX -

SIM

SIM900

+ RX TX -

SIM











ENGLISH

Page 17 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

SIFCPKNX

The 001SIFCPKNX interface card greatly expands the communica-

tion possibilities of CP control units, enabling them to communicate

with the KNX system. It is connected to the port available on all

control units and in turn makes the communication ports available.

BOARD DESCRIPTION

a Main RS232 port;

 USB port. A USB port is available for connecting to a PC in order

to perform programming with the SWLink software. In this case, the

connection between the control unit and the PC is direct and can be

made using a simple USB cable.

- During USB connection to the PC, or when IFLAN connection is

active, communication from the control unit to the KNX BUS is in-

terrupted.

- The USB connection is not active in the presence of IFLAN cards.

 KNX key and programming LED;

 KNX BUS terminal block;

 Second RS232 port: This connects the device to the control unit

via the IFLAN terminal block when present.

INSTALLATION

CAUTION. In order for a security event to be properly published

on the KNX bus, the minimum duration of this event must be equal

to or greater than 3 seconds.

CAUTION. For programming details, contact your service

representative.

CAUTION. The device must be installed by qualified personnel,

following the current regulations and guidelines for KNX installations.

001SIGPRS

Telephone dialler suitable for all CP control units, complete with

whip antenna. It allows users to send SMSs and voice messages

as well as receive SMSs and DTMF commands for remote control.

It also allows users to manage the security system remotely via the

Came Domotic app and/or via Came Touchscreen and also manage

Video Verification in combination with PIR camera sensors.

BOARD DESCRIPTION

a Connector for GSM antenna.

 Connector for connecting to the CP control unit

 SIM slot

 Connector for connecting the IGSM interface on the control unit

board

 Status indicator LED

 Slot for micro SD (supplied) containing the module software

 Connectors for connecting the 001SDGETH/001SDGWF acces-

sories

 Connector for Konnex touchscreen/interface

 Assembly turrets

 Labels with the WiFi credentials (present even if the 001SDGWF

accessory is not installed)

LED STATUS

On, Off, Flashing (2 flashes per second), Slow flashing (1

flash every 3 seconds), Quick flashing (1 flash per second)

DL1 GREEN - Cloud Connection Status

Absent

Connecting

Connected

DL2 RED - Internet connection Status

Absent

Connecting

Connected

001SIGPRS

001SDGETH

001SDGWF

CP6099WL

ENGLISH

Page 18 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

DL3 RED - Module power-on Status

GSM module off

GSM module on

DL4 GREEN - GSM modem Status

Off

GSM network not found

GSM network found

Connected to the GSM network

INSERTING THE SIM CARD

The SIM card must be inserted and removed while the power is

disconnected.

After powering on the control unit, check that the GSM LED indi-

cates that the SIM has been registered correctly.

The SIM card (not included) must have the following characteristics:

- VOICE + SMS: incoming/outgoing calls and SMS management,

- VOICE + SMS + DATA:connection to the Cloud, e-mailing for video

verification,

- VOICE + SMS + MMS: sending MMSs for video verification.

INSTALLATION

With the control unit not powered, connect the connector  on the

module to the CN1 connector on the control unit, using the flat cable

supplied and, if present, connect the accessories to the module via

the dedicated connectors.

Insert the SIM into the slot .

Secure the 001SIGPRS module to the control unit board using the

turrets supplied, making sure to connect the IGSM connector 

correctly to the CN2 connector.

CONFIGURATION

The device is detected automatically by the control unit. To register

the device on CameConnect (www.cameconnect.net), please refer

to the relative manual.

MANUAL FIRMWARE UPDATE

Use the following link:

http://www.cameconnect.net/came/pages/download.html

to download the latest software version available for the 001SIG-

PRS module: camesecurity_<major>-<minor>.bin

Copy the file “camesecurity_<major>-<minor>.bin” to the first

level of a USB drive.

1. Remove the USB-ETH (001SDGETH) or USB-WIFI (001SDGWF)

dongle to free up a USB port.

2. Insert the drive on which the new software has been saved in the

USB connector.

3. After a few seconds, the red DL2 LED and the green DL1 LED light

up quickly alternately way to indicate the software update phase

(this phase lasts a few dozen seconds).

4. Once the update is complete, all the LEDs go off and the module

reboots.

5. Remove the USB drive and put back the dongle you removed

previously.

6. The module is operational.

















ENGLISH

Page 19 - Manual code: FA00373-EN ver. 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

Managing the control unit using the Came Mobile app

Using the Came Mobile app , just a few clicks means you can

securely connect to your control unit and check the status of all

the environments, activate scenarios and interact with your home

remotely, simply from your smartphone or tablet.

In order to manage the control unit via the Came Mobile app, you

must first install firmware version 2.3.00 or later, install the 001SIG-

PRS GPRS module and install the Came Domotic app 1.4.7 or later

on your smartphone/tablet.

Security can be managed via a local connection, connecting direct-

ly to the IP address of the 001SIGPRS module interfaces (in this

case, the 001SDGWF or 001SDETH accessories are necessary) or

via remote connection - in this case, you need to register on the

CameConnect portal (see CameConnect chapter).

CONFIGURING CONNECTIVITY

The 001SIGPRS module can be connected to CameConnect using

a GPRS connection, Ethernet connection (using the 001SDGETH

accessory) or WiFi connection (using the 001SDGWF accessory).

To program the parameters related to connectivity, use the

following: SWLink in version 2.1.4, while for programming the

graphic maps, Came D Sw software version 1.2.2 or later is re-

quired.

CameConnect connectivity via GPRS [GPRS]

If connecting to CameConnect via GPRS, set the following:

a Select [GPRS] from the types of connection.

 Select [Connectivity] [GSM].

 Enter the [APN] (Access Point Name).

Generally, telephone operators publish this information on their

websites.

 If you need to change the telephone number.

 Enter the [User Name] and [Password] for data connection.

Generally, telephone operators publish this information on their

websites.

CameConnect connectivity via Ethernet [ETHERNET]

If connecting to CameConnect via Ethernet , it is necessary to use

the 001SDGETH accessory to connect to the user network.

In the default configuration, the Ethernet interface is config-

ured in static mode with the following IP address: 192.168.1.100.

These settings should be adapted to the customer’s network.

To set up connectivity via Ethernet, you must:

a Select [ETHERNET] from the types of connection.

 Select [Connectivity] [ETHERNET].

 Enable the DHCP Server if present in the customer’s network.

In this way, the 001SIGPRS module automatically acquires the net-

work parameters.

In the case of programming with DHCP, if a reading of the

control unit configuration is taken, the IP Address/Netmask fields

show the address acquired by the interface dynamically.

If you want to set up the module with a static address, disable this

preference.

 Set the parameters in a manner consistent with the network

where the device is connected. You also need to set the DNSs for

connectivity to CameConnect.

 Port to connect the PC for programming with SWLink.

 Choosing the keypad to emulate.

In addition to connection to CameConnect for remote manage-

ment, the 001SDGETH accessory also allows the control unit to be

connected to a local network so that it can be managed by Came

TouchScreens and using the Came Domotic app on the same local

network.













Keycode: 577A13EEFA6F1D27 560121

001SIGPRS

WiFi SSID:CameSecurity - 1D27

WiFi Pass:qtEc35vtggBqgQwc

Keycode: 577A13EEFA6F1D27 560121

PXGPRS

WiFi SSID:CameSecurity - 1D27

WiFi Pass:qtEc35vtggBqgQwc

ENGLISH

Page 20 - Manual code: FA00373-EN ver. 1 05/2016 © CAME S.p.A. - The data and information provided in this manual are subject to change at any time without prior notice.

CameConnect connectivity via WIFI [WIFI]

If connecting to CameConnect via WiFi , it is necessary to use the

001SDGWF accessory. In this case, it is necessary to connect the

module to the user’s WiFi network.

In the default configuration, the WiFi is configured as an Access

Point  so that the PIR Camera sensors (IR sensors related to video

verification) or other network devices can connect directly to it.

- The default SSID is “CameSecurity-xxxx” (where xxxx are the last

4 digits of the keycode)

- Password: <Random string of 16 characters>

The WiFi data is written on the label inside the package.

The device’s Wi-Fi network is hidden, so it is not visible on