Page is loading ...
20
STAGE PAGE
86 Rear radiator hoses 289
87 Rear sway bars 292
88 Rear cooling system (part 1) 295
89 Rear cooling system (part 2) 298
90 Rear cooling system (part 3) 302
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2021
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
FORD GT
324
Faros y capÓ
Stage 86: Tuyaux
de refrigeration arriere
YOUR PARTS
86-A
86-B
86-C
86-A Hoses for the rear cooling
system
86-B Rear radiator hose 1
86-C Rear radiator hose 2
325
step by step
STEP 86-2
In the same way, mount the
rear radiator hose 1 (86B), the
shorter one, on the linchpin
located on the bottom of the
front cover of the engine block
(79B), indicated as “linchpin 2”
in the photo.
STEP 86-1
Get the previously
assembled rear axle. Place
the holed end of the rear
radiator hose 2 (86C), the
longer one, on the linchpin
located on the front cover
of the engine block (79B),
indicated in the photo
as “linchpin 1”. Slide the
hose completely onto the
linchpin to secure it.
86-C
Linchpin
1
Linchpin
2
86-B
79-B
79-B
FORD GT
326
STEP 86-3
Get the passenger compartment you
assembled previously. Insert the hoses for the
rear cooling system (86A) into the two holes
in the rear passenger compartment battery
box (30A), to the right of the ignition coil
(21G). Secure all the hoses rmly. To make
sure they are in the correct position, ensure
that the top linchpin on the hoses is larger
than the bottom one.
STAGE COMPLETE!
86-A
20A
21-G
Gros
Linchpin
Linchpin
fin
327
step by step
Faros y capÓ
87-A Rear sway bar
87-B Rear sway bar mounts
87-C Rear sway bar end links
87-D Rear panhard rod
87-E FP02 Screws 1.8 x 4 mm Ø 3 mm
87-F FP01 Screws 2.3 x 4 mm Ø 3.8 mm
Stage 87: Rear sway bars
YOUR PARTS
87-A
87-C87-B
87-D
FP01 FP02
FORD GT
328
STEP 87-1
Attach one of the sway
bar end links (87C) to the
rear right wishbone (72A),
as shown in the photo.
Ensure that the sway bar
is the right way round: the
part that hooks onto the
wishbone is the one with
the two thicker rings.
STEP 87-3
Attach the rear sway bar (87A)
so that all the ends are hooked
onto one of the sway bar end
links (87C), as shown in the
photo.
STEP 87-2
Attach the second sway bar
end link (87C) to the rear left
wishbone (73A), as shown.
Ensure that the sway bar is
the right way round.
72-A
87-A
72-A
87-C
87-C
87-C 87-C
87-C
87-C73-A
73-A
329
step by step
`
STEP 87-4
Place the rear sway bar
(87A) on the rear suspension
connector (74D). Attach a rear
sway bar mount (87B) and
secure with two FP02 screws.
87-B
FP02
87-B
87-A
87-A
74-D
STEP 87-6
Attach one of the rear panhard
rods (87D) to the left-hand side,
by positioning the end with the
ring underneath the hub link
(73D). Secure the two parts with
one FP01 screw.
STEP 87-5
Repeat the previous step to
attach the rear sway bar mount
(87B) on the left side. To secure
the rear sway bar (87A) to the
rear suspension connector (74D),
position the mount and secure
with two FP02 screws.
87-B
87-A
FP02
87-D
73-D
FP01
74-D
74-D
FORD GT
330
STAGE
COMPLETE!
STEP 87-7
Repeat the previous steps on the
right-hand side. Put the end of
the rear panhard rod (87D) with
a ring on it over the hub link
(72D). Secure the two parts with
one FP01 screw.
87-D
72-D
FP01
331
step by step
Faros y capÓ
YOUR PARTS
88-A
88-B
88C 88-D
88-E
88-F
88-G
'
88-A Rear right air intake
duct
88-B Rear right air intake
duct cover
88-C Rear left air intake
duct
88-D Rear left air intake
duct cover
88-E Rear cooling system
inlet hose 1
88-F Rear cooling system
inlet hose 2
88-G Transmission lines
88-H FP01 Screws 2.3 x 4
mm Ø 3.8 mm
88-I FD10 Screws 2.3 x 5
mm Ø 3.8 mm
FD10
FP01
Stage 88: Rear cooling
system (part 1)
FORD GT
332
STEP 88-1
Get the chassis you assembled in the
previous stages. Place the rear right
air intake duct (88A) and rear left air
intake duct (88C) on the rear section
of the chassis, so as to identify which
side each duct goes. To facilitate this,
look at the position of the parts in the
photo, with the hole in the inner corner
facing upwards and towards the centre
of the chassis.
STEP 88-3
Insert the rear left air intake duct (88C)
into the slot in the main chassis (38A).
Insert the linchpin on the panel into
the hole in the inner corner of the air
intake duct, as you did in the previous
step.
STEP 88-2
Turn the chassis over and insert the
rear right air intake duct (88A) into its
slot in the main chassis (38A). Insert the
linchpin on the panel into the hole in
the inner corner of the air intake duct,
ensuring that it faces the same way as
in the photo.
88-C
88-C
88-A
88-A
Linchpin
Linchpin
38-A
38-A
332
333
step by step
STEP 88-4
After mounting the two ducts, turn the
chassis over again and secure each duct
with one FP01 screw, as shown in the
photo.
STEP 88-6
Get the piece with the rear axle and
engine and place it in front of the
engine compartment. Put the engine
into its compartment and hook the
two rear panhard rods (87D) over the
attachment points indicated in the
previous step, as shown in the photo.
STEP 88-5
Find the two attachment points in the
engine compartment, indicated in the
photo by blue circles; this where the rear
panhard rod (87D) will go. Place the top
hose of the rear cooling system hoses
(86A) to the right.
87-D
333
FP01
FORD GT
334
STEP 88-7
Install the rear part in the engine
compartment and make sure the two rear
panhard rods (87D) are positioned correctly.
Check that the left (75A) and right (75B)
engine mounts are aligned perfectly with
the rear chassis frame (39A).
STEP 88-9
Now tighten the FP01 screw
behind the right side of the
rear transmission subframe
(71A).
STEP 88-8
After checking that the engine in in the
correct position, insert one FP01 screw
into the right side, behind the rear
transmission subframe (71A), at the
height of the right engine mount (75B).
87-D
75-B
75-B
71-A
71-A
75-B
75-A
75-A
39-A
39-A
FP01
FP01
335
step by step
STEP 88-11
Turn the chassis over and
nish securing the engine by
inserting and tightening four
FD10 screws, as shown in the
photo.
REMAininG
PARTS
Keep the unused parts
in a safe place, as you
will need them in the
upcoming stages. Check
that you have all the parts
indicated in this list.
STEP 88-10
Repeat the previous steps on the left
side. Tighten one FP01 screw behind
the rear transmission subframe (71A),
at the height of the left engine mount
(75A). Secure the ends of the two engine
mounts to the rear chassis frame (39A)
with one FD10 screw.
71-A
75-A
FP01
REMAINING PARTS
88-B Rear right air intake
duct cover
88-D Rear left air intake duct
cover
88-E Rear cooling system
inlet hose 1
88-F Rear cooling system
inlet hose 2
88-G Transmission lines
88-B 88-D
88-E
88-F
88-G
FD10
FD10
39-A
FORD GT
336
Faros y capÓ
YOUR PARTS
89-A
89-B
89-C
'
Stage 89: Rear
cooling system (part 2)
89-A Engine hose 1
89-B Engine hose 2
89-C Bonnet grille frame
89-C FD09 Screws 1.8 x 3.5
mm Ø 3 mm
FD09
337
step by step
STEP 89-1
Get the spark plug connector (85B),
attached to the spark plug wires
(84A), and slide it onto linchpin on
top of the ignition coil (21G).
STEP 89-3
Pull the rear radiator hose
1 (86B) out of the inside of
the engine. Insert it into
the hole behind the engine
compartment tank (22F), as
shown in the photo.
STEP 89-2
Connect the two ends of the fuel
line to the fuel pump (23B). Make
sure that each end is inserted
correctly in the top of each part of
the pump.
5-H
5-H
21-G
85-B
23-B
86-B 22-F
337
85-B
86-B
FORD GT
338
STEP 89-4
Position the end of the
radiator hose 2 (86C), which
is sticking out of the engine
next to the rear radiator hose
1 (86B), over the hole in the
battery box cover (32B) closest
to the wheel, as shown in the
photo. Press it in rmly.
STEP 89-6
Get the transmission lines (88G),
provided with the previous stage.
Place the rectangular side in its
housing over the rear transmission
subframe (71A), so that the two
linchpins in the housing are aligned
with the holes in the subframe. The
correct position can be determined
by the different sized linchpins. Press
the transmission lines rmly onto the
subframe.
STEP 89-5
Insert the end of the hose (81E) into
the hole in the engine compartment
tank ller tube (22G), as shown in the
photo.
86-C
81-E
88-G
71-A
32-B
22-G
338
81-E
86-A
86-A
22-F
339
step by step
STEP 89-7
Take the left transmission line
(88G) and insert it into the
right transmission case (61A) by
applying pressure, as shown in the
photo.
STEP 89-8
Feed the right transmission
line (88G) down through
the gap between the right
transmission case (61A) and
the chassis. Push it hard so
that it wedges underneath
the transmission case, as
shown in the photo.
61-A
61-A
88-G
88-G
FORD GT
340
Faros y capÓ
90-A Lower front panel
90-B FP09 Screws 1.8 x 3.5 mm
Stage 90: Rear cooling
system (part 3)
YOUR PARTS
90-A
FP09
341
step by step
STEP 90-3
Insert the rear cooling
system inlet hose (88E) into
the hole in the narrow end
of the left side of the right
rear air intake cover (88B),
as shown in the photo.
Then insert the rear cooling
system inlet hose 2 (88F)
into the hole in the wider
end.
STEP 90-2
Find the rear cooling system hoses (86A), the
two hoses with the fake connectors on the
ends. The one starting from the circular box
goes into the left hole in the back of the rear
left air intake duct cover (88D), number 1 in
the photo. The second goes into the right hole,
number 2.
STEP 90-1
Place the rear left air intake duct
cover (88D) in its housing on
the rear chassis frame (39A). To
position it correctly, make sure
that the side with two holes
is facing outwards (as shown
in the photo), and that the
side with three holes is facing
inwards. Insert the two linchpins
on the inside of the cover into
the protrusions on the base, by
applying a little pressure.
12
88-E
86-A
88-B
88-B
88-D
88-D
39-A
88-F
/