Halco DFDLG4-12-CS Installation guide

Halco
Brand
Halco
Model
DFDLG4-12-CS
Type
Installation guide

This manual is also suitable for

Halco ProLED Select Direct Fit
Gimbal Installation Guide
®
© 2023 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. 05102023
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Cleveland | Houston | Chicago | Phoenix
Figure 1
Figure 3
hole in the ceiling, as figure 1
2. Connecting the wire as figure 2 and make sure insulation protection,
then pull the fixture spring in vertical direction.
3. Pushing the fixture to the ceiling hole, and make sure well fixed.
Please consult a qualified electrician for hanging fixture and wiring.
CAUTION: Before starting the installation,disconnect the power by turning
off the circuit breaker or by removing the fuse at the fuse box. Carefully unpack and identify all parts
before assembly
Junction box
Ceiling
LED
Driver
AC-L
AC-N
AC-L
AC-N
LED
Driver
Figure 2
Recessed
Downlight Spring
clip
Figure 1
Figure 3
hole in the ceiling, as figure 1
2. Connecting the wire as figure 2 and make sure insulation protection,
then pull the fixture spring in vertical direction.
3. Pushing the fixture to the ceiling hole, and make sure well fixed.
Please consult a qualified electrician for hanging fixture and wiring.
CAUTION: Before starting the installation,disconnect the power by turning
off the circuit breaker or by removing the fuse at the fuse box. Carefully unpack and identify all parts
before assembly
Junction box
Ceiling
LED
Driver
AC-L
AC-N
AC-L
AC-N
LED
Driver
Figure 2
Recessed
Downlight Spring
clip
Figure 1
Figure 3
hole in the ceiling, as figure 1
2. Connecting the wire as figure 2 and make sure insulation protection,
then pull the fixture spring in vertical direction.
3. Pushing the fixture to the ceiling hole, and make sure well fixed.
Please consult a qualified electrician for hanging fixture and wiring.
CAUTION: Before starting the installation,disconnect the power by turning
off the circuit breaker or by removing the fuse at the fuse box. Carefully unpack and identify all parts
before assembly
Junction box
Ceiling
LED
Driver
AC-L
AC-N
AC-L
AC-N
LED
Driver
Figure 2
Recessed
Downlight Spring
clip
Figure 1
Figure 3
hole in the ceiling, as figure 1
2. Connecting the wire as figure 2 and make sure insulation protection,
then pull the fixture spring in vertical direction.
3. Pushing the fixture to the ceiling hole, and make sure well fixed.
Please consult a qualified electrician for hanging fixture and wiring.
CAUTION: Before starting the installation,disconnect the power by turning
off the circuit breaker or by removing the fuse at the fuse box. Carefully unpack and identify all parts
before assembly
Junction box
Ceiling
LED
Driver
AC-L
AC-N
AC-L
AC-N
LED
Driver
Figure 2
Recessed
Downlight Spring
clip
Figure 1
Figure 3
hole in the ceiling, as figure 1
2. Connecting the wire as figure 2 and make sure insulation protection,
then pull the fixture spring in vertical direction.
3. Pushing the fixture to the ceiling hole, and make sure well fixed.
Please consult a qualified electrician for hanging fixture and wiring.
CAUTION: Before starting the installation,disconnect the power by turning
off the circuit breaker or by removing the fuse at the fuse box. Carefully unpack and identify all parts
before assembly
Junction box
Ceiling
LED
Driver
AC-L
AC-N
AC-L
AC-N
LED
Driver
Figure 2
Recessed
Downlight Spring
clip
  • Page 1 1

Halco DFDLG4-12-CS Installation guide

Halco
Brand
Halco
Model
DFDLG4-12-CS
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents