Right Weigh PP-003-0061 is a versatile load scale designed for exterior use on spring suspension vehicles. With its ability to support up to 3 strain sensors, it can accurately measure the weight of a wide range of vehicles, including straight trucks, trailers, and dollies. Featuring a sunlight-readable LCD display, the PP-003-0061 provides clear weight readings in various lighting conditions.
Right Weigh PP-003-0061 is a versatile load scale designed for exterior use on spring suspension vehicles. With its ability to support up to 3 strain sensors, it can accurately measure the weight of a wide range of vehicles, including straight trucks, trailers, and dollies. Featuring a sunlight-readable LCD display, the PP-003-0061 provides clear weight readings in various lighting conditions.
ONBOARD LOAD SCALE
EXTERIOR DIGITAL | SPRING SUSPENSION
2
LOW
Thank you for choosing to drive more and scale less! Here at Right
(503) 628-0838
(888) 818-2058 - Toll Free (USA ONLY)
FOLLOW US!
WELCOME
2
IMPORTANT!
the vehicle.
www.rwls.com/warranty.
Trailer / Dolly
Wagon Trailer
Straight Truck
Sensor Checking / Adjustment
Set / Change Security PIN Code
Warranty Statement & Return Policy
4
5
7
7
8
8
9
10
11
12
13
14
15
CONTENTS
3
ONBOARD LOAD SCALE
EXTERIOR DIGITAL | SPRING SUSPENSION
4
7-¼”
5”
2”
POWER
ON/OFF
MENU/
ENTER
(1)
CAL HIGH (2)
CAL LOW (3)
DOWN ARROW
(4)
UP ARROW
62 mm
127 mm
406 mm
87 mm
184 mm
208 mm
114 mm
114 mm
Scan here to download the “Right
Right Weigh Load Scales App:
Scan here for instrucons
along with a video tutorial
Technical Specificaons:
5
SCALE INSTALLATION
& ELECTRICAL CONNECTIONS
INSTALL CONNECTION HARNESS
STRAIN SENSOR
CONNECTIONS
POWER CONNECTION
RED = POWER
RS-232 FORWARD
CONNECTION
HARNESS
i
iii
ii
SECTION 1
SECTION 2
INSTALL STRAIN SENSOR(S)
1
manufacturer. Doing so may void the warranty with the vehicle manufacturer.
CHOOSE LOCATION
2
3
!
!
SCALE INSTALLATION
& ELECTRICAL CONNECTIONS
6
4
RED wire to a
i
(OPTIONAL)
POWER CONNECTION
STRAIN SENSOR CONNECTIONS
SET NUMBER OF CONNECTED STRAIN SENSORS
ii
iii
DO NOT connect directly to a baery or any constant power source, gauge should be connected to a switched
source so that it can be disconnected from power when not in use. Most users connect the power to vehicle
marker lights or the AUX/ABS wire.
Electrical connecons MUST be insulated, see Appendix A for instrucons.
!
If you need to change the number of strain sensors at any point, follow these steps:
1. Turn off the scale
2. Press and hold the C HIGH buon and the MENU buon, press the POWER buon, then release all 3
3. Use the UP arrow buon to change the number of strain sensors to the number desired
4. Turn off the scale to save seng
Please note that by changing the number of strain sensors the scale recognizes, all calibraon data will be LOST
!
7
OPERATING MODES
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
PRESS
HOLDING
PRESS
CHANGING OPERATING MODES
AVG
IdP
F1b2
1
2
The load scale can only be setup in one operang mode at a me. If the mode is changed, the calibraon
data will be reset to factory defaults, requiring re-calibraon.
!
WAGON TRAILER
1
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 1 -
VEHICLE CONFIGURATION OPERATING MODE
Spring Suspension Front Single Axle
2
Axle Group 2 - Spring Suspension Rear Tandem Axles
1
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 1 - Spring Suspension Front Axle
Axle Group 2 - Spring Suspension Rear Axle
2
SPRING
SUSPENSION
WALKING BEAM
SUSPENSION
MACK CAMELBACK
SPRING SUSPENSION
8
OPERATING MODES
TRAILER / DOLLY
1
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 1 -
VEHICLE CONFIGURATION OPERATING MODE
Spring Suspension Single, Tandem, or Tri Axle
Group
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 1 -
VEHICLE CONFIGURATION OPERATING MODE
Spring Suspension Steer Axle
Axle Group 2 - Mack Camelback Spring Suspension Rear
Tandem Axles
1 2
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 1 - Walking Beam Spring Suspension Rear Tandem
Axles
1
*DRIVE AXLE GROUP ONLY
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
Axle Group 2 - Walking Beam Spring Suspension Rear Tandem
Axles
2
1
Axle Group 1 - Spring Suspension Steer Axle
9
& ADJUSTMENT
Only perform the following checks when the vehicle is empty
ADJUST STRAIN SENSOR
With the gauge displaying the sensor value that needs adjusted,
remove the sheet metal cover of the corresponding strain sensor.
range is within 6.500 and 7.500.
REPEAT FOR ADDITIONAL SENSORS
the strain sensor(s).
ENTER DIAGNOSTICS MENU
scale.
sensors B and C.
LOWER NUMBER
RAISE NUMBER
PRESS
HOLDING
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
www.rwls.com
ON/OFF
HOLD 3 SECONDS
CALIBRATE
C
HIGH
1C
LOW
234
ENTER
MENU
i
EL-003-0004
1 2 3 4 C/H C/L KG LBS
EXIT DIAGNOSTICS MENU
!
4
5
i
1
2
3
ii
iii
!
CALIBRATION & UNITS
10
CHANGING UNITS
RE-CALIBRATION
rs.
tches
EMPTY CALIBRATION POINT
LOADED CALIBRATION POINT
CALIBRATION
weight, etc.
!
SET/CHANGE PIN CODE
OPTIONAL
11
again to save the code.
“Good”.
PRESS
HOLDING
PRESS
HOLDING
PRESS
PRESS
PRESS
SET PIN CODE
CHANGE PIN CODE
12
OPERATE & WEIGH
TROUBLESHOOTING
13
Scale Does Not Power On Scale is not connected to a
vehicle marker lights or the AUX/ABS wire). If there is a
Scale is connected directly to
vehicle marker lights or the AUX/ABS wire). The scale is
Polarity is incorrect
Cannot Change
PROBLEM CAUSE SOLUTION
Weight Readings
level surface
Park on level concrete ground.
the Gauge
Scale is connected to a constant
vehicle marker lights or the AUX/ABS wire). If the gauge
Scale is connected to another
device
device.
Gauge reading “noAir”
receiving air (If 2 air sensors are
set to Average mode and one
isn’t receiving air, gauge will read
noAir message)
noAir message.
APPENDIX A
14
Aer all connecons have been made, heat shrink
the enre group of splices so that it seals on the
outer jacket of both cables.
With a heat gun or heat torch, heat the connector
unl it shrinks completely around each wire end.
Make sure you do not burn the wire jacket.
After crimping and heat shrinking
Add heat shrink
After heat shrinking
Crimp each end of the wire into the connector with
a wire crimp tool (tool not provided).
WARRANTY & RETURN POLICY
15
Warranty Statement
Return Policy and Authorizaon
Repairs/Replacements
©2015-2022 Right Weigh, Inc. All rights reserved.
Right Weigh, Inc.
PP-003-0061 Revision F
Thank you for choosing to drive more and scale less! Here at Right
Weigh, we are commied to making our products simple to install and
easy to use. We understand that installaon can vary between vehicles
and yours may not be described in this manual. In any event, our
technical support team is ready to answer your quesons!
THANK YOU
FOR YOUR BUSINESS
(503) 628-0838
(888) 818-2058 - Toll Free (USA ONLY)
FOLLOW US!
RightWeighInc
rightweigh_inc
rwlsinc
right-weigh-inc-
CONTACT US FOR
ADDITIONAL SUPPORT
SCAN FOR ADDITIONAL RESOURCES
rwls.com/manuals-resources/
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Right Weigh PP-003-0061 is a versatile load scale designed for exterior use on spring suspension vehicles. With its ability to support up to 3 strain sensors, it can accurately measure the weight of a wide range of vehicles, including straight trucks, trailers, and dollies. Featuring a sunlight-readable LCD display, the PP-003-0061 provides clear weight readings in various lighting conditions.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Right Weigh 201-EBT-30B-WB Installation guide
-
Right Weigh 201-EBT-20B Installation guide
-
Right Weigh 201-EBT-20B-TT Installation guide
-
Right Weigh 310-PP Series User manual
-
Right Weigh 201-EBT-30B Installation guide
-
Right Weigh 201-EBT-22B Installation guide
-
Right Weigh 201-EBT-20B-WB Installation guide
-
Right Weigh 201-EBT-12B Installation guide
-
Right Weigh 201-EBT-10B Installation guide
-
Other documents
-
RW Onboard Load Scale User manual
-
RW 201-EBT-02 Exterior Digital Onboard Load Scale User manual
-
RW 403-SK User manual
-
RW 202-DDG-04 User manual
-
RW 250 Series Onboard Load Scale Exterior Analog User manual
-
RW 201-EBT-20B Installation guide
-
RW 310-PP Series User manual
-
RW 510 series User manual
-
Flintec FT-30M On-Board Weighing Indicator User manual
-
Detecto LSM Series Owner's manual
