Anova F1027 Installation guide

Anova
Brand
Anova
Model
F1027
Type
Installation guide
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Hammer DrillHammer
Pencil
9/16"Wrench
Wire Brush
Level
Safety Glasses
Rally & Ultra Benches
Optional: (4 or 6) 3/8"
Rubber Washers
90130A050
(4 or 6) 3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
Masonry Drill Bit Set
3/16", and 3/8"
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
Rally Ultra
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6.
7.
Repeat steps 3 - 6 until all anchors are installed.
8.
!
24
5
Care should be given to avoid rubbing the powder coating o the foot. A
3/8" rubber washer is a suitable replacement option. Mount the bench to the
ground by placing a washer and a nut onto each anchor. Leave the hardware
nger tight until all of them have been installed. Verify that the bench is level
before tightening the anchors. Tighten all of the hardware with a 9/16" wrench.
Remove the nuts and washers o of the anchors. Align the mounting holes of
the bench over top of the anchors and slide it down into place.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Place bench in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference
page 3.
Rally & Ultra Benches
8.28.1
7
Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
10/03/2018
Rally & Ultra Benches
FOOT MOUNT SIZE CHART
SKU # Width Length
L1420
F1365 16.375" 76.785"
F1361 16.375 53.035"
D1027
D1027COM
L1337
C1337
19.375" 76.660"
D1360
F1360
F1027
19.375 76.688
F1026
D1026
L1343
F1389
19.375 52.785
D6002
D6002COM 21.500" 76.188"
D6003 21.500" 52.316"
D6011 22.025" 76.125"
Width
Length
Ø.50" (4 PLCS)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova F1027 Installation guide

Anova
Brand
Anova
Model
F1027
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents