anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 9/16" Open-end or box-end wrench
• Ratchet with 9/16" socket
• 18 Volt (or higher) driver with No. 3
Phillips head bit
Assembly Instructions
Wainwright
RCPWC6 - Wainwright 6' Contour Bench
RCPWC4 - Wainwright 4' Contour Bench
BENCH COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(2) Backrest
End Caps
(2) Seat
End Caps
(2) Bench
Supports
(1 or 2) Backrest
Braces
(12) 3/8"-16 X 2 1/4"
Carriage Bolts
(2) 3/8"-16 X 3"
Carriage Bolts
(7 or 14) Phillips
Head Screws
(2) 3/8"-16 1 1/4"
Hex Head Bolts
(14) 3/8"-16
Hex Nuts
(14) 3/8"Lock
Washers
(2) 3/8"-16
Nylock Nuts
(18) 3/8" Flat
Washers
ASSEMBLY:
Inspect the shipping container contents for damage and to determine that all
components and hardware are present.
1.
2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to
nish.
3. Place four of the seat planks across the two bench supports.
4. Place the two seat end caps over each end of the seat planks, aligning the mounting
holes with the plank mounting holes. Insert six 3/8"-16 X 2 1/2" carriage bolts through
front two planks and back plank, end caps, and bench supports. Place a 3/8" at
washer, 3/8" lock washer, and 3/8" hex nut on each of the bolts. Tighten the hardware
nger tight so adjustments can be made later.
NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or
petroleum jelly be applied to the screw threads.
NOTE: When laying out the Planks, make sure the face of the Planks with the pre-
drilled pilot holes faces downward.
1
(1) Seat Support (7) Seat/Backrest Plank
Bench Supports
The assembly is a two-person operation.
Seat Plank
3/8"-16 X 2 1/2"
Carriage Bolt
3/8" Flat Washer
3/8" Lock Washer
3/8"-16 Hex Nut
Seat End Cap
Wainwright 6' Contour Bench Wainwright 4' Contour Bench
2
Phillips Head Screw
5. Tilt the Bench back so it rests on the tops of the bench supports.
Locate one or two backrest braces. If assembling the 4' bench
position the brace in the center or the bench. If assembling the 6'
bench position each brace about 2 from the ends of the bench.
Use the driver with Phillips head bit to drive Phillips head screws
through the backrest brace mounting holes and into the pre-
drilled pilot holes in the seat planks.
NOTE: Insert screws into the two front planks and the back plank
only.
6. Locate the seat support and position it so that the ange with
the mounting holes aligns with the mounting holes in the bench
support.
Install a 3/8"-16 X 3” long carriage bolt through the seat plank,
bench support, and seat support at the end of the bench. Place
a 3/8" at washer and 3/8"-16 nylock nut on the end of the
carriage bolt and tighten nger tight.
Repeat this step on the opposite side.
7. Place a 3/8" at washer on one of the 3/8"-16 1 1/4" hex head
bolts and insert the bolt through the mounting holes in one end
of the bench supports and the seat support. Place a 3/8" at
washer, 3/8" lock washer, and 3/8"-16 hex nut on the end and
tighten nger tight.
Use the driver with Phillips head bit to install a Phillips head
screws through the seat support, backrest brace, and into the
pre-drilled pilot holes in the seat plank.
Repeat the rst part of the step on the opposite side if
assembling a 4' bench. Repeat both parts of the step on the
opposite side if assembling a 6' bench.
8. The remaining seat planks become backrest planks. Place these three
planks across the upper portion of the bench supports and backrest braces.
NOTE: When laying out the Planks, make sure the face of the Planks with
the pre-drilled pilot holes faces downward.
Place backrest end caps over the ends of the planks and secure them using
the six remaining 3/8"-16 X 2 1/2” carriage bolts, 3/8" at washers, 3/8"
lock washers, and 3/8"-16 hex nuts.
3/8"-16 X 3"
Carriage Bolt
3/8" Flat Washer
3/8"-16 Nylock Nut
Seat Support
3/8"-16 1 1/4"
Hex Head Bolt
3/8" Flat Washer
3/8" Flat Washer
3/8" Lock Washer
3/8"-16 Hex Nut
Phillips
Head Screw
3/8"-16 X 2 1/2" Carriage Bolt
Backrest End Cap
3/8" Flat Washer
3/8" Lock Washer
3/8"-16 Hex Nut
Backrest Plank
Copyright 2018 ANOVA® Made in USA. 3
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
02/06/2018
9. Turn the bench upright and use the driver with Phillips head bit to install
the remaining Phillips head screws through the backrest brace or braces
and into the pre-drilled pilot holes in the backrest planks.
10. Tighten all of the carriage bolt and hex head bolt hardware sets
with the 9/16" open-end or box-end wrench and the ratchet with
a 9/16" socket.
11. Move the bench to the desired location.
12. Aer two weeks, retighten all of the hardware.
Phillips
Head Screws
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET 1 OF 1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 1/24/2018
DWG NO
TITLE
SIZE
D
SCALE
REV
0.12 : 1
19.57"
68.00"
.50"
6' BENCH FOOT MOUNT
4' BENCH FOOT MOUNT
Assembly and Replacement Parts
Seat/Backrest Plank
Seat End Cap
Backrest End Cap
Bench Support
Backrest Brace
Seat Support
A A
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 1/25/2018
DWG NO
TITLE
SIZE
D
SCALE
REV
0.17 : 1
19.57"
44.00"
.50"
19.57"
19.57"
68.00"
O.50"
O.50"
44.00"
/
