anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 1/2" Open-end or box-end
wrench
• Ratchet with 1/2" socket
• Level
Assembly Instructions
Victory, In Ground
F3021
F3024
F3030
F3033
D3021
D3024
F3035
F3017
F3040
BENCH COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
(2) In Ground Bench Supports (1) Bench Seat
(4) 5/16" - 18 X 1 1/4"
Hex Head Bolts
(8) 5/16" Flat Washers (4) 5/16" - 18
Nylock Nuts
ASSEMBLY:
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
1.
2. Lay all parts on a so work surface or on the shipping
packaging to prevent damage to nish.
3. Align the mounting holes in the bracket on the bench
support with the mounting holes in the bench seat frame.
Place a at washer onto one of the 1 1/4” hex head bolts
and insert the bolt through both parts, with the bolt head
toward the outside surface of the bench seat. Place a
washer and nylock nut on the inside end of the bolt and
tighten nger tight.
NOTE: Installing the bolt in this direction reduces the risks
of scratching during use.
Install another bolt in the same manner through the other
set out mounting holes on the other side of the bench
support and bench seat.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied
to the screw threads.
1
5/16" Flat Washer
5/16" - 18
Nylock Nut 5/16" - 18 X 1 1/4"
Hex Head Bolt
5/16" Flat Washer
In Ground Bench Support
Bench Seat
-
-
-
-
-
-
-
-
-
6' Exp Steel Flat Bench, Trad Edge
8' Exp Steel Deep Flat Bench , Trad Edge
6' Exp Steel Flat Bench, Rolled Edge
8' Exp Steel Flat Bench, Rolled Edge
6' Perf Steel Flat Bench, Trad Edge
8' Perf Steel Flat Bench, Trad Edge
4' Exp Steel Deep Flat Bench, Trad Edge
6' Exp Steel Deep Flat Bench, Trad Edge
8' Exp Steel Deep Flat Bench, Trad Edge
Model F3033
Model F3017
Expanded Steel Perforated Steel
OR
Copyright 2018 ANOVA® Made in USA. 2
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
02/06/2018
4. Attach the other bench support to the bench seat in the same manner, installing the 1 1/4” hex head bolts from the outside inward.
Tighten the hardware aer both bolts are installed.
5. Determine the location for bench, locate underground utilities and avoid them while digging holes for the concrete bases.
6. The walls of the concrete base should be vertical and smooth to minimize
the eects of frost upheaval. This can be achieved with the use of concrete
forms, such as Sonotube®. Consider extending the concrete base below the
frost line to eliminate the possibility of frost upheaval. Consult a professional
for loose or unusual soil conditions.
7. Create a temporary structure to support the bench, at the desired height
and level, while the concrete is curing.
19.75" 21.75" MIN
Ground Level
O 12.00" MIN
8.
9.
Fill the forms with concrete and insert the bench supports, centered in the
forms, until the bench is supported by the temporary structure. Allow the
bench supports to ll with concrete. Crown the concrete cap to optimize
drainage.
Aer the concrete has cured remove the temporary structure and retighten
all hardware.
72.91"
57.16"
37.16"
O2.28"
O2.28"
O2.28"
Bench Seat
In Ground
Bench Support
Assembly and Replacement Parts
4' IN GROUND BENCH SUPPORT MOUNT
6' IN GROUND BENCH SUPPORT MOUNT
8' IN GROUND BENCH SUPPORT MOUNT
/
