Edsal 1UGK7 Assembly Manual

Brand: Edsal

Model: 1UGK7

Type: Assembly Manual

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety

hazard. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE

UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom.

DO NOT OVERLOAD. Use care when working with metal parts.

When moving the unit, always push from the sides. NEVER push from the front, back, or top. This can cause a “tipping” hazard,

which can result in a serious injury to yourself or others. NEVER pull the unit during movement, push the unit to the location.

Always move the unit over a flat level surface. Rough surfaces cause the unit to vibrate, which causes the unit’s load to increase in

weight, or again may cause a “tipping” hazard which can result in a serious injury to yourself or others. Do not store any items on

the top of the unit during movement, this may cause a “falling” hazard that can injure yourself or others.

Instruction Manual - Mobile Bin Unit - 1UGK7

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams

and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer

head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at,

(773) 475-3000 and request customer service. We can also be reached on the internet at the following email address :

[email protected].

To obtain replacement parts, please provide the following information : Model # - Part # & Description - Location Purchased - Date Purchased

10 Shelf

33” w

36 Bins

Step 1

Install casters in to posts.

Press the plastic caster supports fully into the

welded bracket on the

bottom of each of the 4 posts.

Insert caster

Into Post bottom

Make sure caster

is fully inserted

Description Qty. Part # Size

Caster 4 Swivel Single 3"

Post 4 RUPT6302 63"

Beam - Double Rivet 4 RBBR3202 33"

Brace - Double Rivet 4 RBBR1402 15"

Beam - Single Rivet 16 RBBE3201 33"

Brace - Single Rivet 2 RBBE1401 15"

Wire Deck - 3 Large Bins 3 WD1533L 33" x 15"

Wire Deck - 4 Medium Bins 3 WD1533M 33" x 15"

Wire Deck - 5 Small Bins 3 WD1533S 33" x 15"

Wire Deck - Flat 1 WD1533 33" x 15"

Large Plastic Bin 9 PB15106 10.6" x 6.1" x 15.4"

Medium Plastic Bin 12 PB15076 7.5" x 6.3" x 15.4"

Small Plastic Bin 15 PB15063 6.0" x 3.3" x 15.4"

Step 2

Assemble the front and back frames.

Using 2 of the 33” Double-Rivet

Beams assemble the front frame as

shown. Insert the rivets on the

Beams into the slots on the Posts

and gently tap down until they are

fully seated.

Repeat the process to build a

matching back frame.

Assemble the

front frame

Repeat to assemble

the rear frame

Step 3

Insert rivets

and tap down

Use the 33” long,

2 Rivet Beams

Connect the front frame to the rear

frame, using the 2 Rivet, 15”

braces.

Add the center supports, using the

1 Rivet, 33” long Beams and 1

Rivet, 15” long Braces. Install in

the 20th holes from top of Post.

Use the 15” long, 2 Rivet Braces for the

top and bottom connections

Use the 33” long, 1 Rivet Beams and the

15” long, 1 Rivet Braces for the center

connections

15” long,

1 Rivet Brace

33” long,

1 Rivet Beam

15” long,

2 Rivet Brace

15” long,

2 Rivet Brace

33” long,

2 Rivet Beam

33” long,

2 Rivet Beam

20th hole

from post

top

Flat Wire Deck

Step 4

Install the remaining 33” long,

1 Rivet Beams at the recommended

hole spacing between beams.

As before, insert the rivets on the

Beams into the slots on the Posts

and tap them down until they are

fully seated.

Step 5

Beginning with the bottom level, install the Wire

Decking and Bins. The Wire Decks are formed

to fit either 3 large, 4 medium, or 5 small bins.

Install the large bins on the bottom and small

bins on the top as illustrated. Place the wire

deck on the beams and set the bins on the deck.

Start at the bottom level and work your way up.

The flat wire deck is placed on the top level and

can be used as a shelf.

33” long,

1 Rivet Beams

2 Holes

4 Holes

Begin with the bottom level and the large bins,

then work upward

Small Bins

3 levels of 5 bins

Medium Bins

3 levels of 4 bins

Large Bins

3 levels of 3 bins

Edsal 1UGK7 Assembly Manual

Edsal 1UGK7 Assembly Manual

Edsal 1UGK7 Assembly Manual

Related papers

Other documents