Safety Instructions
Safety Instructions
Safety Instructions
-
-
-
maximum capacity = 50 lbs. per shelf (evenly distributed), 500 lbs. total for unit
maximum capacity = 50 lbs. per shelf (evenly distributed), 500 lbs. total for unit
maximum capacity = 50 lbs. per shelf (evenly distributed), 500 lbs. total for unit
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety
hazard. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE
UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
DO NOT OVERLOAD. Use care when working with metal parts.
When moving the unit, always push from the sides. NEVER push from the front, back, or top. This can cause a “tipping” hazard,
which can result in a serious injury to yourself or others. NEVER pull the unit during movement, push the unit to the location.
Always move the unit over a flat level surface. Rough surfaces cause the unit to vibrate, which causes the unit’s load to increase in
weight, or again may cause a “tipping” hazard which can result in a serious injury to yourself or others. Do not store any items on
the top of the unit during movement, this may cause a “falling” hazard that can injure yourself or others.
Instruction Manual -
Mobile Bin Unit - 1UGK7
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams
and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer
head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
10 Shelf
10 Shelf
10 Shelf
-
-
-
33” w
33” w
33” w
-
-
-
36 Bins
36 Bins
36 Bins
Step 1
Step 1
Step 1
Install the casters by inserting the caster stems
into the sockets that are in the bottom of
each post.
Make sure that the stem is fully inserted.
Make sure caster
is fully inserted
Insert caster stem
Into
socket
Mfd. for Grainger International Inc.
Lake Forest, IL 60045
Printed in China
6-008/1
Description Qty. Size
Caster 4 3"
Post - RUPT6302 4 65"
Beam - Double Rivet 4 33"
Brace - Double Rivet 4 14.5"
Beam - Single Rivet 16 33"
Brace - Single Rivet 2 14.5"
Wire Deck - 3 Large Bins - WD1533L 3 33" x 15"
Wire Deck - 4 Medium Bins - WD1533M 3 33" x 15"
Wire Deck - 5 Small Bins - WD1533S 3 33" x 15"
Particle Board 1 33" x 15"
Large Plastic Bin - PB15106 9 10.6" x 6.1" x 15.4"
Medium Plastic Bin - PB15076 12 7.5" x 6.3" x 15.4"
Small Plastic Bin - PB15063 15 6.0" x 3.3" x 15.4"
-UR4416BIN36
36Bin Storage Rack
9 Shelf - 57"H x44"W x 16"D
Concealed Post
57
"
Beam
-
Double Rivet
44"
Brace- Double Rivet
16"
Beam- Sin
g
le Rivet
10
8
44"
Wire Deck-3 Small Bins
43"x15"
Wire Deck-4 Small Bins
43"x15"
43"x15"
43"x15"
Wire Deck-5 Small Bins
Wire Deck
-
6 Small Bins
Laminated Board
2
2
Enlar
g
e Plastic Bin
6
43.4"x15.4"
15.4"x12.4"x6.6"
Lar
g
e Plastic Bin
8
15.4"x10"x6.6"
Medium Plastic Bin
10
15.4
"
x7.5
"
x6.6
"
Small Plastic Bin
12
1
5
.4"x
5
.
9
"x
3
.
5
"
/
12
Post Ca
p
Safety Instructions - maximum capacity =150 Ibs. per shelf (evenly distributed),1350 Ibs. total for unit
The unit should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety
hazard. Do not use this unit for anything other than the manufactures intend purpose. DO NOT STAND ON ANY PART OF THE
UNIT,OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom.DO
NOT OVERLOAD. Use care when working with metal parts.
Insert post cap into
the concealed post
Make sure post cap
is fully tight
Install the post cap into the bottom and top of
each post, Make sure that the post cap is fully
tight.
Page1
8
2
1
8
15.4"x5.9"x3.5"
Step 2
Step 2
Step 2
Assemble the front and back frames.
Using 2 of the 33” Double-Rivet
Beams assemble the front frame as
shown. Insert the rivets on the
Beams into the slots on the Posts
and gently tap down until they are
fully seated.
Repeat the process to build a
matching back frame.
Assemble the
front frame
Repeat to assemble
the rear frame
Step 3
Step 3
Step 3
Insert rivets
and tap down
Use the 33” long,
2 Rivet Beams
Connect the front frame to the rear
frame, using the 2 Rivet, 14.5”
braces.
Add the center supports, using the
1 Rivet, 33” long Beams and 1
Rivet, 14.5” long Braces. Install in
the 20th holes from top of Post.
Use the 14.5” long, 2 Rivet Braces for the
top and bottom connections
Use the 33” long, 1 Rivet Beams and the
14.5” long, 1 Rivet Braces for the center
connections
14.5” long,
1 Rivet Brace
33” long,
1 Rivet Beam
14.5” long,
2 Rivet Brace
14.5” long,
2 Rivet Brace
33” long,
2 Rivet Beam
33” long,
2 Rivet Beam
20th hole
from post
top
A
ssemble the front frame
A
Insert rivets
and tap down
B
Insert rivets
and tap down
Repeat assemble the
rear frame
44"
Page2
16" Double Rivet
16" Double Rivet Braces install in
the 18th holes and 28th holes from
bottom of Post.
Insert rivets
and tap down
Braces.
B
Insert rivets
and tap down
A
C
Insert rivets
and tap down
Insert rivets
and tap down
C
4
A
C
B
B
Particle Board Deck
Step 4
Step 4
Step 4
Install the remaining 33” long,
1 Rivet Beams at the recommended
hole spacing between beams.
As before, insert the rivets on the
Beams into the slots on the Posts
and tap them down until they are
fully seated.
Step 5
Step 5
Step 5
Beginning with the bottom level, install the Wire
Decking and Bins. The Wire Decks are formed
to fit either 3 large, 4 medium, or 5 small bins.
Install the large bins on the bottom and small
bins on the top as illustrated. Place the wire
deck on the beams and set the bins on the deck.
Start at the bottom level and work your way up.
The particle board deck is placed on the top level
and can be used as a shelf.
33” long,
1 Rivet Beams
2 Holes
2 Holes
2 Holes
4 Holes
4 Holes
4 Holes
4 Holes
4 Holes
4 Holes
Begin with the bottom level and the large bins,
then work upward
Small Bins
3 levels of 5 bins
Medium Bins
3 levels of 4 bins
Large Bins
3 levels of 3 bins
Page3
44"
6 enlarge bins, 8 large bins, 10
medium bins, 12 small bins. Install the bins as
illustrated. Place the wire deck on the beams and
set the bins on the deck. Start at the bottom level
and work your way up.
The laminated board is placed on the top level
and can be used as a shelf.
Begin with the bottom level and the enlarge bins,
then work upward.
/
