Master VV1238 Operating instructions

Brand: Master

Model: VV1238

Type: Operating instructions

This manual is also suitable for

VV1239

Master VV1238: Your gateway to a smarter and more connected home. With cutting-edge AI technology, this device learns your preferences and routines, allowing for personalized automation and control of your smart devices. From adjusting lighting and temperature to managing entertainment and security systems, the Master VV1238 puts the power of a smart home at your fingertips.

SPEC DATA SHEET

1 | Page MASTER PAINT & CHEMICAL CORP. CARR#127 KM 12.7 BO. MAGAS GUAYANILLA PR 00656

TEL: 787-835-4000 / FAX: 787-835-2965 / E-FAX: 787-966-7180

Rev. 0

Supersedes September, 2016

Masterflex Ultimate Armour 200®

Innovative Cross-Linking Technology

Over 200 hours of water ponding resistance

SECTION 1 - PRODUCT DESCRIPTION

SECTION 2 - TYPICAL USE

SECTION 3 - PRODUCT ADVANTAGE

SECTION 4 - COLO

SECTION 5 - GLOSS

Masterflex Ultimate Armour 200® is an innovative ultra white acrylic elastomeric roof sealer, based on an exclusive cross-linking technology

that resists critical water ponding conditions. It offers outstanding long-term durability and toughness to prevent leakage and fix roofs with

already leaking problems, caused by capillarity, cracks or joints. Highly resistant to damage caused by UV rays, dirt, water or other common

weather elements. It also has excellent adhesion to concrete, polyurethane foam, galvanized metal and aluminum. It can significantly reduce the

interior temperature up to 20 degrees, resulting in energy savings and cooling costs.

Masterflex Ultimate Armour 200® is used for waterproofing and protection of concrete, polyurethane foam, galvanized metal and

aluminum. With additional advantages it is highly resistant to water ponding (200 hours +). However, for a more durable and efficient

protection, all water ponding areas should be fixed with Masterflex Leveling Repair®. If water ponding areas are not fixed, they must be

repaired by the installation of an efficient drain system and annual maintenance. This maintenance should be done by applying two coats of

MASTERFLEX ULTIMATE ARMOUR 200®.

 2 in 1: Primer & Sealer

 Low water absorption and permeability

 Roof Defense Technology: Polyfiber plus® Technology made out

of resins, fibers and additives.

Certified Roof Formula that reduces mold and mildew on the dry

sealer film, maintaining the roof white to save energy.

Brilliant Ultra White finished

Reflective flat finish

SECTION 6 - COMPOSITION

Cross linking acrylic polymer, titanium dioxide and reflective and inert pigments. Free of lead, chromates and mercury.

SECTION 7 – PHYSICAL AND CHEMICAL PROPERTIES

Viscosity: 115 +/- 5 KU (Stormer) Flash Point: None Weight per gallon: 11.30 +/- 0.15 lb/gal

Solids per Volume: 50 +/-1 % Solids per weight: 65+/-1 %



Excellent dirt pickup resistance

 Ultra white. Reflects 98% of solar rays and reduces interior

temperature up to 20°.

 Fast dry

 LOW VOC: 50g/L volatile organic compounds

 Remains flexible in any weather conditions

 Excellent adhesion to concrete, polyurethane foam, galvanized

metal and aluminum

 Coverage: 400 ft² per pail

SPEC DATA SHEET

2 | Page MASTER PAINT & CHEMICAL CORP. CARR#127 KM 12.7 BO. MAGAS GUAYANILLA PR 00656

TEL: 787-835-4000 / FAX: 787-835-2965 / E-FAX: 787-966-7180

Rev. 0

Supersedes September, 2016

SECTION 9 - APPLICATION

SECTION 10 – APPLICATION TOOLS

SECTION 11 – CAUTION

Before attempting to apply, mix the product well in a circular upward-downward motion, preferably with a mechanical agitator. Apply it

using a good quality long hair roller or an airless spray machine. In small areas and corners, it can be applied with a brush. For best results:

Apply in accordance with Guide Specifications, available at Master Paints and Chemical Corp. and at your retail store.

Airless Machine Application: Mix this product with a mechanical mixer. Remove the filter of the suction pump and the machine filter.

Program the machine to apply this product with 1,400 to 1,750 psi and use a fan width of 6 in order to control the overspray of material. Use a

pistol tip for a .29” to a .41” spray. Make sure that rain is not forecasted for that day. If the roof is too hot, spray it lightly with water so that

the sealer does not dry too quickly.

Recommended Film Thickness: 20 mils dry / 40 mils wet

Coverage: Two coats must be applied in order to get the recommended 20 mils dry film thickness (MDFT). Apply each coat in different

directions and wait 12 hours between each coat. Select a clear and sunny day for application.

Coverage 1 coat ft² (m²) per pail

Concrete Surfaces

400 ft² (37.5 m²) per pail @ 10 MDFT

Metal Surfaces

800 ft² (37.5 m²) per pail @ 5 MDFT

Foam Surfaces

400 ft² (37.5 m²) per pail @ 10 MDFT

Thinning: This product is ready to use and should be applied full strength as received in the can. Any thinning of the product will reduce the

percentage of solids, which will adversely affect the dry film thickness and the durability of the applied sealer.

Clean UP: Clean all application equipment with soap and water.

It can be applied using a brush, roller, or atomizer.

HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES

AND AVOID BREATHING OF VAPORS AND SPRAY MIST. USE ONLY WITH ADEQUATE VENTILATION. When applying spray,

use respiratory protection (NIOSH/MSHA TC23C or equivalent), eye protection and protective clothing. Before use, ask and read the Safety

Data Sheet (SDS) of the product, available at Master Paint & Chemical Corp. Close container after each use. KEEP OUT OF REACH OF

CHILDREN.

SECTION 8 – SURFACE PREPA

ATION

Roof surface should be cleaned by eliminating all residues of dust, sand, cement, mold, mildew, and strange particles. Use a water pressure

machine. Roof’s drain system should be repaired if it does not allow water to exit. For concrete roofs, repair holes that are greater than ½ inch

or any water ponding area by using Masterflex Leveling Repair®.

Crack Repair: All joints and cracks have to be sealed. Apply Masterflex Elastomeric Crack Filler® with a spatula and the Masterflex

Fiberglass Patch Weave® on top of cracks, joints, and around all objects that are anchored to the roof, by covering at least two inches more on

each side. Let it dry for 24 hours before applying the roof sealer.

WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD

DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT

WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH approved respirator and prevent skin contact to control

lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by

contacting the USEPA National lead Information Hotline at 1-800-424 LEAD or log on to www.epa.gov/lead.

SPEC DATA SHEET

3 | Page MASTER PAINT & CHEMICAL CORP. CARR#127 KM 12.7 BO. MAGAS GUAYANILLA PR 00656

TEL: 787-835-4000 / FAX: 787-835-2965 / E-FAX: 787-966-7180

Rev. 0

Supersedes September, 2016

The information and recommendations set forth in this Product Data Sheet are based upon test conducted by Master Paints and

Chemical Corp. Since application variables are a major factor in product performance, this information should serve only as a

general guide. Improvements in coating technology may cause future technical data to vary from what is in this bulletin. Consult

your Master Paints and Chemical Corp. representative or call 787 835 4000 to obtain the most recent Product Data Sheet

SECTION 12 – FIRST AID

SECTION 14 – PACKAGING

1 gallon and 5 gallon pails

In case of skin contact, remove product from skin with soap and water. When eye contact with products occurs, rinse affected area with large

amounts of water at least 15 minutes and get immediate medical attention. If swallowed, medical attention is needed immediately. Do not

apply late in the day or when rain or dew is likely. Storage the air tight sealed product in a dry and well ventilated environment. For proper

disposal of excess material, please contact your local city waste management agency. PLEASE DO NOT DISPOSE OF REMNANTS IN

SEWERS.

SECTION 13 – LIMITED WARRANTY

Master Paints & Corp. warranties the original buyer of this product ONLY WHEN APPLIED ACCORDING TO SPECIFIED

INSTRUCTIONS IN THE PRODUCT LABEL (such as surface preparation, crack repair, recommended square feet coverage, and use of

patch weave to reinforce cracks and joints), that MASTERFLEX ULTIMATE ARMOUR 200®will seal against leaks in the roof area where

it is applied for FIVE (5) YEARS after date of purchase. This warranty is only valid when the total roof area is sealed with MASTERFLEX

ULTIMATE ARMOUR 200® including drains, inverted beams, parapets, eaves, and any other adjacent surface that can affect the product

performance. This warranty does not apply to adjacent roof structures that for some reason are joined to it. This product warranty is limited

exclusively to the surface where it was applied. Buyer remedies under this warranty are limited to the replacement of the product or a refund of

the product’s cost when the product does not meet our specifications and quality standards. This warranty does not cover application costs or

other related costs. This warranty will be the only and exclusive remedy available for the buyer and it is non-transferable. MASTER PAINTS

& CHEMICAL, CORP. DOES NOT WARRANTY AND WILL NOT BE LIABLE FOR DAMAGE PRODUCED FOR THE WRONGFUL

USE OF THIS PRODUCT, OR FROM NOT FOLLOWING SPECIFIED INSTRUCTIONS FOR THIS PRODUCT’S USE AND

APPLICATION BY A CONTRACTOR OR THIRD PARTY WITHOUT THE PROPER LICENSE FOR SEALING AND ROOF REPAIR IN

PUERTO RICO. This warranty does not cover problems caused by natural events such as hurricanes, storms, earthquakes, fire, floods, wind,

lightning, and structural defects or causes beyond the control of Master Paints & Chemical, Corp., including the abuse or bad use of the

product or negligence in its use or application. Warranty does not apply when the original application is altered, adequate maintenance is not

provided according to the specified product label instructions, or a structure or construction is added to it. Any claim under this warranty

should be done by written letter addressed to Master Paints & Chemical Corp. on or before 15 days after finding the alleged leak or defect. All

claims received will be verified during a reasonable time. To make this warranty valid, buyer should send by mail before 30 days after

purchasing this product, proof of purchase with his/her name and address to: Master Paints & Chemical, Corp., ATT: Customer Service

Department, P.O. 560248, Guayanilla, PR 00656-0248. This warranty does not apply to commercial works. For such matters, please

communicate with Master Paints & Chemical, Corp. at (787) 835-4000, 835-4001, 835-1295 or 787-740-5254.

SPEC DATA SHEET

4 | Page MASTER PAINT & CHEMICAL CORP. CARR#127 KM 12.7 BO. MAGAS GUAYANILLA PR 00656

TEL: 787-835-4000 / FAX: 787-835-2965 / E-FAX: 787-966-7180

Rev. 0

Supersedes September, 2016

Master VV1238 Operating instructions

Brand: Master

Model: VV1238

Type: Operating instructions

This manual is also suitable for

VV1239

Download PDF

report

Master VV1238 Operating instructions

This manual is also suitable for

Master VV1238 Operating instructions

Related papers

Other documents