MASTER PAINTS & CHEMICAL CORP. CARR # 127 KM. 12.7 BO. MAGAS. GUAYANILLA PR 00656
Tel: 787-835-4000 / Fax: 787-835-2965 / e-fax: 787-966-7180
Rev. January 16, 2015
Page 1 of 2
COLOR SHIELD
Roof Sealer with color * 100% Acrylic Elastomeric
SECTION 1 - PRODUCT DESCRIPTION
SECTION 2 - TYPICAL USE
SECTION 3 - PRODUCT ADVANTAGE
SECTION 4 - COLOR
SECTION 5 - GLOSS
SPEC DATA SHEET
COLOR SHIELD is a single component, air dry acrylic elastomeric roof sealer that provides a thick, high performance, weather resistant seal
on most surfaces, without the need of a primer application. It is highly recommended for the prevention and correction of problems due to roof
filtrations caused by capillarity, crevices, or joints when adding new constructions to those already in existence. COLOR SHIELD is
formulated with acrylic polymers as a base, which provides a formulation of maximum elasticity, creating a highly flexible membrane with
the capacity to contract and expand without affecting the adhesion. It is available in gray, red and green colors.
Color Shield is used to seal on most surfaces such as concrete, asphalt roofs, wood, metal, old or weathered galvanized sheets, and foam
surfaces.
Low VOC content
Excellent UV resistance
2 in 1:Primer & Sealer
Strong resistance to peeling and discoloration
Seal sand protect concrete, asphalt, wood, metal,
weathered galvanized sheets & foam surfaces
Perfect for zinc / aluminum, concrete and woods
roofs
Available colors are: gray, red and green colors.
Satín (10 - 15) @ 60 degrees
SECTION 6 - COMPOSITION
100% Elastomeric Acrylic Resins, free of lead, chromates and mercury.
SECTION 7 – PHYSICAL AND CHEMICAL PROPERTIES
Viscosity: 115 – 120 KU (Stormer) Flash Point: None
Weight per gallon: 10.6+/- 0.3 Lbs. Solids per Volume: (51+/- 1.0) %
Solids by Weight: (60.0 +/- 1.0) % VOC Content: maximum 50 g/lt
MASTER PAINTS & CHEMICAL CORP. CARR # 127 KM. 12.7 BO. MAGAS. GUAYANILLA PR 00656
Tel: 787-835-4000 / Fax: 787-835-2965 / e-fax: 787-966-7180
Rev. January 16, 2015
Page 2 of 2
SECTION 9 - APPLICATION
SECTION 10 – APPLICATION TOOLS
SECTION 11 – CAUTION
SECTION 12 – FIRST AID
SECTION 13 – PACKAGING
1 gallon and 5 gallon pails
Mix this product well using a circular motion. Apply with a roller, brush or airless spray. Let dry for twenty four (24) hours and apply a second
coat for enhanced durability. This product is not formulated for immersion.
Two coats are required for complete sealing. Total dry thickness of roof coating should be 20 mils.
It can be applied using a brush, roller, or airless spray.
Recommended Film Thickness: 10 MDFT (one coat) / 20 MDFT total dry thickness (two coats)
Coverage: Concrete surface: 80 square feet per gallon / 7.5m2 per gallon @ 10 MDTF
Roof Shingles: 80 square feet per gallon / 7.5m2 per gallon @ 10 MDTF
Metal Roofs: 160 square feet per gallon / 15m2 per gallon @ 5 MDTF
Wood Roofs: 80 square feet per gallon / 7.5m2 per gallon @ 10 MDTF
Thinning: Not recommended.
Dry time: 6 hours to touch
24 hours to recoat
This sealer contains acrylic resins. It can cause eye, skin, or throat irritation. Do not take internally. Close container after each use. When
spray applying, use respiratory protection (NIOSH/MSHA TC23C or equivalent), eye protection and protective clothing. For more information
read the MSDS, available at Master paints and Chemical Corp. KEEP OUT OF REACH OF CHILDREN
In case of skin contact, flush from skin with water and then wash thoroughly with soap and water. In case of eye contact, flush immediately
with large amounts of water for at least 15 minutes and get emergency medical attention. If swallowed, get medical attention immediately. For
more information, request Material Safety Data Sheet of the product available at Master Paints & Chemical Corp
SECTION 8 – SURFACE PREPARATION
The roof or surface should be free from dust, sand, cement, rust, fungus and strange particles. This can be accomplished by means of a
pressure washer. Improve all water drainage areas where necessary. Old or weathered galvanized sheets: remove rust with wire brush.
Thoroughly clean the entire surface with a solution of household detergent and water. Rinse and let it dry. Replace loose fasteners, old
fasteners must be covered with Master Crack Filler and let to dry 24 hours before apply COLOR SHIELD.
Concrete and Masonry (New Surfaces): 1. All new concrete and masonry new surfaces must be left to cure a minimum of thirty (30) days
for proper adhesion and product durability. 2. If there are several areas with severe water ponding, it is recommended to correct all water
ponding areas with “Master Leveling Repair” and wait at least thirty (30) days to cure before applying COLOR SHIELD. On aspha lt roofs,
make sure to completely remove any oils and grease present. 3. Crack Repair: Clean cracks, and apply “Master Elastomeric Crack Filler”
with a putty knife over the cracks and one inch to both sides. Put the “Fiberglass Patching Weave” on top while the product remains wet.
Apply a second layer of “Master Elastomeric Crack Filler” over the “Fiberglass Patching Weave” completely. Let dry for 24 hours before
applying COLOR SHIELD. Repeat this procedure to Protect the equipment located over the roof top (TV antennas, solar heather, air
conditioner consoles, electric power, water storage tank. etc).
WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT
WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH approved respirator and prevent skin contact to control
lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you star, find out how to protect yourself and your family by
contacting the USEPA National lead Information Hotline at 1-800-424 LEAD or log on to www.epa.gov/lead.
The information and recommendations set forth in this Product Data Sheet are based upon test conducted by Master Paints and Chemical Corp.
Since application variables are a major factor in product performance, this information should serve only as a general guide. Improvements in
coating technology may cause future technical data to vary from what is in this bulletin. Consult your Master Paints and Chemical Corp.
representative or call 787 835 4000 to obtain the most recent Product Data Sheet.
/
