Focal Point ID+ 4.5" x 4.5" Wall Wash Trimless FLC44W-ST Installation guide

Brand: Focal Point

Model: ID+ 4.5" x 4.5" Wall Wash Trimless FLC44W-ST

Type: Installation guide

This manual is also suitable for

ID+ 4.5" x 4.5" Downlight Trimless FLC44D-ST

IS0608 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 4

non-emergency - thermally protected, non-ic

id+ 4.5” square trimless housing

FLC44D-ST | FLC44W-ST

Luminaires must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

key

power off power on

level attention

see additional instructions

LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.

emergency - integral test switch

bar hangers

sold separately

flc44d-st | flc44w-st

cp - emergency/non-emergency

flc44d-st | flc44w-st

6 1/2” max6 1/2” max

6 ” min 6 ” min

TO SET CEILING

THICKNESS SEE FOCAL

POINT INSTRUCTION SHEET

IS0609

3WOOD STUDS

2b x4

2a x4

WALL WASH ORIENTATION

WALL

IS0608 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 4

Fixtures must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

make electrical connections

METAL STUDS

MUD-IN

DO NOT REMOVE DUST

COVER UNTIL TAPE AND

MUD-IN COMPLETE

6 1/2” max6 1/2” max

6 ” min 6 ” min

CLEAN CEILING SURFACE FREE

OF DUST AND DEBRIS

USE DUST COVER TO ALIGN MUD RING

WITH HOUSING

MUD TAPE

DRYWALL

REMOVE ADHESIVE BACKING FROM MUD RING

IS0608 REV. B 2018 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 4

Fixtures must be installed by a qualied electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

WOOD CEILING

wood ceiling installation kit parts list

5/16" miniature

rabbeting bit with

1/16" cut depth

wood routing jig

3m command poster strip

#136 (qty. 40)

2 3

ADHERE COMMAND POSTER STRIPS

TO WOOD ROUTING JIG

ADHERE WOOD ROUTING JIG

TO WOOD CEILING SURFACE 4CREATE STARTER HOLE

4” 4”

CLEAN WOOD CEILING SURFACE

AND WOOD ROUTING JIG FREE

OF DUST AND DEBRIS

.170”

Tr im Recess

9a8

INSTALL 5/16" MINIATURE RABBETING BIT

WITH 1/16" CUT DEPTH SET DEPTH OF RABBETING BIT

USE TRIM TO DOUBLE CHECK DEPTH

5CREATE MAIN HOLE USING

WOOD CEILING JIG AS GUIDE 6REMOVE WOOD ROUTING JIG

FROM WOOD CEILING SURFACE 7

SQUARE CORNERS

5" 5"

Contractor is responsible for adequately reinforcing walls and/or ceilings to support xture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or

ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC

is prohibited.

DRIVER SERVICE

EMERGENCY - INTEGRAL TEST SWITCH

DO NOT MATE CONNECTOR

UNTIL INSTALLATION

IS COMPLETE AND A.C.

POWER IS SUPPLIED

A B

BATTERY UNIT CONNECTOR INSIDE

SEE BATTERY

MANUFACTURER

INSTRUCTIONS