Focal Point ID+ 3.5" x 3.5" Adjustable Accent Trimless FLCS33-ST / LCS33 Installation guide

Brand: Focal Point

Model: ID+ 3.5" x 3.5" Adjustable Accent Trimless FLCS33-ST / LCS33

Type: Installation guide

IS0649 REV. D 2022©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 5

non-emergency - thermally protected, non-ic

id+ 3.5" square trimless adjustable

FLCS33

Luminaires must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.

ALL GRID LUMINAIRES MUST BE SECURED TO STRUCTURE ABOVE.

optional - bar hangers sold separately

ic/cp

key

power off power on

levelattention

see additional

instructions

trimless with

solite lens

trim

trimless without

solite lens

METAL STUDS

WOOD STUDS

2a x4

4 1/8”4 1/8”

ceiling cutout

IS0649 REV. D 2022©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

make electrical connections

54 minimum ceiling thickness: 1/2"

maximum ceiling thickness: 1"

MUD-IN

4 1/8”4 1/8”

clean ceiling surface

free of dust and debris

remove adhesive backing

from mud ring

do not remove dust

cover until tape and

mud-in complete

DRYWALL TAPE

(BY OTHERS)

DRYWALL

MUD RING

MUD

APPLY TAPE AND DRYWALL COMPOUND AT LEAST 8-12” OUT FROM APERTURE

use foam cylinder to align mud

ring with housing collar opening

4 6

IS0649 REV. D 2022©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

5CREATE MAIN HOLE USING

WOOD CEILING JIG AS GUIDE 6REMOVE WOOD ROUTING JIG

FROM WOOD CEILING SURFACE

2 3

ADHERE COMMAND POSTER STRIPS

TO WOOD ROUTING JIG

ADHERE WOOD ROUTING JIG

TO WOOD CEILING SURFACE 4CREATE STARTER HOLE

SQUARE CORNERS

WOOD CEILING

wood ceiling installation kit parts list

5/16" miniature

rabbeting bit with

1/16" cut depth

wood routing jig

3m command poster strip

#136 (qty. 40)

4” 4”

CLEAN WOOD CEILING SURFACE

AND WOOD ROUTING JIG FREE

OF DUST AND DEBRIS

scrape away eXcess

mud compound from

mud ring to eXpose

trim recess

IS0649 REV. D 2022©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

TILT

2a1a

USE ADJUSTMENT HANDLE

TO TILT UP TO 35°

OPTIC SERVICE

1 2 3

ALIGN TABS ON BACK OF OPTIC

WITH SLOTS ON FILTER MOUNT

ROTATE

USE ADJUSTMENT HANDLE

TO ROTATE UP TO 362°

CREATE TRIM RECESS

USING RABBETING BIT

.170”

Tr im Recess

9a8

INSTALL 5/16" MINIATURE RABBETING BIT

WITH 1/16" CUT DEPTH SET DEPTH OF RABBETING BIT

USE TRIM TO DOUBLE CHECK DEPTH

Contractor is responsible for adequately reinforcing walls and/or ceilings to support ﬁxture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or

ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC

is prohibited.

5 64

DRIVER SERVICE

2 31

TRIM INSTALLATION

1 2

4 5

TO PREVENT ELECTRICAL SHOCK,

DISCONNECT ELECTRICAL SUPPLY

BEFORE SERVICING

TO PREVENT ELECTRICAL SHOCK,

DISCONNECT ELECTRICAL SUPPLY