Focal Point ID+ 3.5" Adjustable Accent Trimless FLCS3-RT / LCS3 Installation guide

Brand: Focal Point

Model: ID+ 3.5" Adjustable Accent Trimless FLCS3-RT / LCS3

Type: Installation guide

IS0647 REV. D 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 5

non-emergency - thermally protected, non-ic

id+ 3.5" round trimless adjustable

FLCS3

Luminaires must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.

ALL GRID LUMINAIRES MUST BE SECURED TO STRUCTURE ABOVE.

optional - bar hangers sold separately

ic/cp

4 1/8”

ceiling cutout

key

power off power on

levelattention

see additional

instructions

trimless with

solite lens

trim

trimless without

solite lens

METAL STUDS

WOOD STUDS

2a x4

IS0647 REV. D 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

make electrical connections

54 minimum ceiling thickness: 1/2"

maximum ceiling thickness: 1"

MUD-IN

”

clean ceiling surface

free of dust and debris

remove adhesive backing

from mud ring

use foam cylinder to align mud

ring with housing collar opening

do not remove dust

cover until tape and

mud-in complete

DRYWALL TAPE

(BY OTHERS)

DRYWALL

MUD RING

MUD

APPLY TAPE AND DRYWALL COMPOUND AT LEAST 8-12” OUT FROM APERTURE

IS0647 REV. D 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

5CREATE MAIN HOLE USING

WOOD CEILING JIG AS GUIDE 6REMOVE WOOD ROUTING JIG

FROM WOOD CEILING SURFACE 7

INSTALL 5/16" MINIATURE RABBETING BIT

WITH 1/16" CUT DEPTH

2 3

ADHERE COMMAND POSTER STRIPS

TO WOOD ROUTING JIG

ADHERE WOOD ROUTING JIG

TO WOOD CEILING SURFACE 4CREATE STARTER HOLE

WOOD CEILING

wood ceiling installation kit parts list

5/16" miniature

rabbeting bit with

1/16" cut depth

wood routing jig

3m command poster strip

#136 (qty. 40)

4”

CLEAN WOOD CEILING SURFACE

AND WOOD ROUTING JIG FREE

OF DUST AND DEBRIS

scrape away eXcess

mud compound from

mud ring to eXpose

trim recess

IS0647 REV. D 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 5

Fixtures must be installed by a qualiﬁed electrician (check with local and national codes for proper installation).

To prevent electrical shock, disconnect electrical supply before installation or servicing.

TILT

USE ADJUSTMENT HANDLE

TO TILT UP TO 35°

OPTIC SERVICE

1 2 3

ALIGN TABS ON BACK OF OPTIC

WITH SLOTS ON FILTER MOUNT

ROTATE

USE ADJUSTMENT HANDLE

TO ROTATE UP TO 362°

.065”

Trim Recess

8a 9

CREATE TRIM RECESS

USING RABBETING BIT

SET DEPTH OF RABBETING BIT

USE TRIM TO DOUBLE CHECK DEPTH

Contractor is responsible for adequately reinforcing walls and/or ceilings to support ﬁxture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or

ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC

is prohibited.

5 64

DRIVER SERVICE

2 31

TRIM INSTALLA-

1 2

4 5

TO PREVENT ELECTRICAL SHOCK,

DISCONNECT ELECTRICAL SUPPLY

BEFORE SERVICING

TO PREVENT ELECTRICAL SHOCK,

DISCONNECT ELECTRICAL SUPPLY