Focal Point ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST Installation guide

Focal Point
Brand
Focal Point
Model
ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST
Type
Installation guide

This manual is also suitable for

Focal Point ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST is a versatile lighting solution designed for various applications. Its key features include:

  • Trimless design for a seamless integration into your ceiling, creating a minimalist and elegant look.
  • Thermally protected and non-IC, ensuring safe operation without the risk of overheating.
  • Multiple cone options (short, super short, and tall) allow you to customize the light distribution to suit your specific needs.
  • Suitable for use with wood or metal studs, providing installation flexibility.

Focal Point ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST is a versatile lighting solution designed for various applications. Its key features include:

  • Trimless design for a seamless integration into your ceiling, creating a minimalist and elegant look.
  • Thermally protected and non-IC, ensuring safe operation without the risk of overheating.
  • Multiple cone options (short, super short, and tall) allow you to customize the light distribution to suit your specific needs.
  • Suitable for use with wood or metal studs, providing installation flexibility.
IS0761 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 1 of 4
id+ 3.5" square trimless housing
FLC33D | FLC33W
Luminaires must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING.
non-emergency - thermally protected, non-ic
optional - bar hangers sold separately
ic/cp
Flc33d | Flc33W
Flc33d/Flc33W
tall cone
dnt
Keep shaded area Free From obstrUction aboVe ceiling
Key
poWer oFF
poWer on
leVel
attention
see additional
instrUctions
WALL WASH ORIENTATION
WALL
x2
1
2.64”
.50”
.50”
3.16”
10.61”
10.61”
2.64”
.50”
.50”
3.16”
10.61”
10.61”
2
short cone
dns
SUPER
SHORT CONE
dss
IS0761 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 2 of 4
Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
METAL STUDS
x4
4
WOOD STUDS
3a x4 x4
3b
5minimum ceiling thickness: 1/2"
maximum ceiling thickness: 1-1/2"
MUD-IN
maKe electrical connections
6
COLLAR MUST OVERLAP BUT NOT EXCEED CEILING MATERIAL
4 1/8”4 1/8”
1
clean ceiling sUrFace
Free oF dUst and debris
3
remoVe adhesiVe bacKing
From mUd ring
2
5
Use Foam cylinder to align mUd
ring With hoUsing collar opening
4 6
IS0761 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 3 of 4
Fixtures must be installed by a qualified electrician (check with local and national codes for proper installation).
To prevent electrical shock, disconnect electrical supply before installation or servicing.
WOOD CEILING
Wood ceiling installation Kit parts list
5/16" miniatUre
rabbeting bit With
1/16" cUt depth
Wood roUting jig
3m command poster strip
#136 (qty. 40)
2 3
ADHERE COMMAND POSTER STRIPS
TO WOOD ROUTING JIG
ADHERE WOOD ROUTING JIG
TO WOOD CEILING SURFACE 4CREATE STARTER HOLE
X4
4” 4”
1
CLEAN WOOD CEILING SURFACE
AND WOOD ROUTING JIG FREE
OF DUST AND DEBRIS
7
do not remoVe dUst
coVer Until tape and
mUd-in complete
8
DRYWALL TAPE
(BY OTHERS)
DRYWALL
MUD RING
MUD
APPLY TAPE AND DRYWALL COMPOUND AT LEAST 8-12” OUT FROM APERTURE
10
9
scrape aWay eXcess
mUd compoUnd From
mUd ring to eXpose
trim recess
Contractor is responsible for adequately reinforcing walls and/or ceilings to support fixture weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or
ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC
is prohibited.
IS0761 REV. B 2022 ©Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL 60632 | www.focalpointlights.com 4 of 4
DRIVER SERVICE
1 2
10
CREATE TRIM RECESS
USING RABBETING BIT
.170”
Tr im Recess
9a
TO PREVENT ELECTRICAL SHOCK,
DISCONNECT ELECTRICAL SUPPLY
BEFORE SERVICING
8
INSTALL 5/16" MINIATURE RABBETING BIT
WITH 1/16" CUT DEPTH SET DEPTH OF RABBETING BIT
USE TRIM TO DOUBLE CHECK DEPTH
9b
5CREATE MAIN HOLE USING
WOOD CEILING JIG AS GUIDE 6REMOVE WOOD ROUTING JIG
FROM WOOD CEILING SURFACE 7
SQUARE CORNERS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Focal Point ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST Installation guide

Focal Point
Brand
Focal Point
Model
ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST
Type
Installation guide
This manual is also suitable for

Focal Point ID+ 3.5" x 3.5" Downlight Trimless FLC33D-ST is a versatile lighting solution designed for various applications. Its key features include:

  • Trimless design for a seamless integration into your ceiling, creating a minimalist and elegant look.
  • Thermally protected and non-IC, ensuring safe operation without the risk of overheating.
  • Multiple cone options (short, super short, and tall) allow you to customize the light distribution to suit your specific needs.
  • Suitable for use with wood or metal studs, providing installation flexibility.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents