urmet domus MT101-013 Technical Manual
- Category
- Door intercom systems
- Type
- Technical Manual
The urmet domus MT101-013 is a compact 2-wire handsfree video door phone that allows you to see and speak to visitors at your door from anywhere in your home. It features a 7-inch color LCD display, a built-in camera with night vision, and a sleek, modern design that will complement any home décor. With its easy-to-use interface and a variety of features, the urmet domus MT101-013 is the perfect way to enhance your home security and convenience.
The urmet domus MT101-013 is a compact 2-wire handsfree video door phone that allows you to see and speak to visitors at your door from anywhere in your home. It features a 7-inch color LCD display, a built-in camera with night vision, and a sleek, modern design that will complement any home décor. With its easy-to-use interface and a variety of features, the urmet domus MT101-013 is the perfect way to enhance your home security and convenience.
sec.2i
−−−−
1
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
SECTION 2I
(REV. A)
PANEL
Download from www.urmet.com Technical Manuals area.
SECTION CONTENTS
ELECTRICAL AND MECHANICAL SPECIFICATIONS .....................2
CONFIGURATION ............................................................................2
TECHNICAL SPECIFICATIONS OF THE MODULES .......................2
DOOR UNIT SET-UP MODULES .....................................................2
Door units .....................................................................................3
BUTTON MODULES ........................................................................4
Call button contact separation .....................................................4
Button module wiring ...................................................................4
Name tag replacement .................................................................5
SPECIAL MODULES ........................................................................5
Repertory modules Ref. 1145/50 .................................................5
Blank modules Ref. 1145/59 ........................................................5
DDA Module with voice messages Ref. 1158/47 .........................6
Hearing impaired people module Ref. 1158/48 ............................7
CAMERA UNIT MODULES ...............................................................8
Technical specications ...............................................................8
Imaging angles .............................................................................8
Camera Ref. 1758/40 -/49 ............................................................8
Camera Ref. 1758/91 ................................................................... 9
METAL FLUSH-MOUNTING BOXES................................................9
Joining ush-mounting boxes ......................................................9
PLASTIC FLUSH-MOUNTING BOXES ........................................... 10
Joining ush-mounting boxes ....................................................10
FRAMES AND MODULE HOLDERS...............................................10
Module holder installation ..........................................................10
Frame installation .......................................................................11
FLUSH-MOUNTED PANEL ACCESSORIES ..................................11
Rain hood with wall cover frame ................................................11
WALL-MOUNTED PANEL ACCESSORIES ....................................12
Case and hood with frame and module holder ..........................12
CONVERSATION PRIVACY DEVICE FOR “1+1” WIRE
SYSTEMS Ref. 1158/74 .................................................................13
SINTHESI STEEL PANEL INSTALLATION ..................................... 14
RECONDITIONING OF OLD SYSTEMS (RETROFIT) ..................... 15
Frame adapter for k-steel ush mounting box ...........................15
Installation on Sinthesi ush mount boxes .................................16
DIMENSIONS .................................................................................17
4+n WIRE DOOR PHONE SYSTEMS
Examples of modular constructions with various capacities .........18
1+1 WIRE DOOR PHONE SYSTEMS
Examples of modular constructions with various capacities .........22
COAX VIDEO DOOR PHONE SYSTEMS
Examples of modular constructions with various capacities .........26
5 WIRES VIDEO DOOR PHONE SYSTEMS
Examples of modular constructions with various capacities .........30
2
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
SINTHESI STEEL PANELS
Sinthesi Steel is a vandal resistant push button panel made of steel,
suitable for harsh environment.
Sinthesi Steel is the evolution of Sinthesi push button panel, with the
same modular structure. For this reason, with a reduced number of
components and shelf items cards it is possible to realize any types
and congurations of push button panels.
The product range continuity is guaranteed by the possibility to use
Sinthesi Steel devices when the existing ush mount box is the one
used for Sinthesi or K-Steel push button panels.
Special care has been dedicated to new modules, optimized to
make installation quicker by using pre-cabled wires with connectors,
implementing new modules as DDA (Disability Discrimination Act)
used to know system operation and ILA (Induction loop Antenna)
modules, that allow hard of hearing people provided with hearing aid
with T operating mode, to hear the door phone conversation.
Sinthesi Steel panels may be used in the following system types:
4+n wire door phone systems.
1+1 wire door phone systems.
colour coax video door phone systems.
colour 5-wire video door phone systems.
ELECTRICAL AND MECHANICAL
SPECIFICATIONS
Front width of one row with frame: 125 mm
Flush mounting box depth: 45 mm
Front projection from the wall: ~15 mm
Front module nish: glossy stainless steel
Button body: Ø 12 mm
Isolation voltage between contacts: 50 Veff
Max. button cut-off current: 2 Aeff
Name tag dimensions: with single button: 52 x 12 mm
Tag and button light: LED
Assorbimento led illuminazione cartellini: 40 mA
Tag protection: self-extinguishing polycarbonate
Max. wire cross-section area for button and light terminals: 1.5 mm
2
Degree of protection: IP45
Corrosion: as per DIN 5342/64 standard
Test duration: 16 hours
Test temperature range: 35 °C
CONFIGURATION
The system allows ush and surface mounting installation and is
composed by the following special groups:
Modules
Flush-mounting box with fairleads
Module holder and frame
Accessories
TECHNICAL SPECIFICATIONS OF THE
MODULES
The following module versions are available:
Door unit set-up
With buttons only
Special (blank or repertory)
With camera
Each module may be clipped onto the module holder for perfect
alignment with the outer frame without the need for screws or tools.
The buttons and name tags are backlit by LED in modules with call
buttons.
•
•
•
•
•
•
•
•
•
•
•
•
SINTHESI STEEL PANELS
ELECTRICAL AND MECHANICAL SPECIFICATIONS - CONFIGURATION
TECHNICAL SPECIFICATIONS OF THE MODULES - DOOR UNIT SET-UP MODULES
The front part can be opened in all modules to facilitate operations.
The frame must be removed for this purpose
DOOR UNIT SET-UP MODULES
The following congurations of door unit set-up modules (i.e. modules
without voice signal processing device) are available:
Without call buttons Ref. 1158/20
With call buttons Ref. 1158/21
With 2 call buttons (*) Ref. 1158/22
(*) For use in 4+n wire door phone systems and coax video door
phone systems only.
Ref.1158/20 Ref.1158/21 Ref.1158/22
DESCRIPTION OF TERMINALS
~12
}
Name tag lighting LED power
~0
U2 Call button 2 (Ref. 1158/22 only)
U1 Call button
G/T2 Call button contact 2 (Ref. 1158/22 only)
G/T Call button common
Obviously, module Ref. 1158/20 is without terminals because it
contains no electrical devices.
•
•
•
sec.2i
−−−−
3
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
DOOR UNITS
DOOR UNIT FOR “4+N” WIRE SYSTEMS Ref. 1145/500
The amplied door unit Ref. 1145/500 is commonly tted in Sinthesi
Steel modular panels in 4+n door phone systems, coax video door
phone systems.
User call feedback is provided on the door unit by means of a LED:
the LED lights up on the door unit set-up panel only if the door phone
or video door phone has picked up the call.
The Ref. 1145/500 device is clipped onto the back on the module by
means of specic clips. No tools are required for this operation. The
door unit occupies the space of two buttons (half a module).
So Ref. 1145/500 can be installed on all the modules designed for
door unit.
DESCRIPTION OF TERMINALS
1A Electronic voice out (from speaker to door phone)
1 Traditional voice out (from speaker to door phone)
+ Door unit power positive
2 Voice in (from microphone to door phone)
L Call feedback LED in (connect to panel button common)
- Door unit power negative
IMPORTANT
Terminal “L” for call feedback cannot be used when the door unit is
tted in traditional call buttons (12V ~ on buzzer).
Use terminal “1A” in systems with electronic call door phones
and terminal “1” for Mod. 1130 door phones.
DOOR UNIT FOR 12VAC 4+N WIRES SYSTEMS Ref. 1145/510
The amplied door unit Ref. 1145/510 can be used with Sinthesi Steel
modules to compose door phone push button panels with 12Vac
power supply.
On the door unit there is a led used for call acknowledgement; it turns
on if the door phone or the video door phone has received the call.
Ref. 1145/510 device is xed by a snap-in mount on the rear side of
the suitable module, using the provided fastener teeth.
No tools are needed to perform this operation.
On the front module, the door unit takes up the space of 2 buttons
(half module).
So this door unit can be installed on all the modules designed for
door unit.
TERMINAL PIN DESCRIPTION
~
}
Door unit power supply: 12Vac
-/~
PS Tone generator output for simultaneous call of up to 2 units
1 Traditional voice out (from speaker to door phone)
1A Electronic voice out (from speaker to door phone)
2 Audio input (from door phone microphone)
IMPORTANT
The call acknowledgement feature is not available for systems with
12Vac buzzer ringer (Mod.1130, Ranger, …) and if the common of
buttons (G/T) is separated.
Use terminal “1A” in systems with electronic call door phones
and terminal “1” for Mod. 1130 door phones.
DOOR UNIT FOR “1+1” WIRE SYSTEMS Ref. 1145/67
Fit door unit Ref. 1145/67 in the panel for speak-and-listen service
in “1+1” wire door phone systems or in 5-wire video door phone
systems.
The Ref. 1145/67 device is clipped onto the back on the module by
means of specic clips. No tools are required for this operation. The
door unit occupies the space of three buttons (3/4th of a module).
Consequently, Ref. 1145/67 only can be tted in:
Door unit set-up module without buttons Ref. 1158/20
Door unit set-up module with 1 single button Ref. 1158/21
DESCRIPTION OF TERMINALS
PS Tone generator output for simultaneous call of up to 2 units
1/~ Door unit power earth
5 (Electrical lock emergency relay control)
~ Door unit power
3 Call buzzer for 1130 door phones
2 Comando elettroserratura
SN Video power on control signal
F Voice
1 Conversation privacy device earth
C1 Conversation privacy button 1
4 Conversation privacy device power
C2 Conversation privacy button 2
AMPLIFICATION REGULATION
All door units have two integrated circuits for external and internal
amplication and an electret microphone (transmitting unit).
Amplication in the two directions may be adjusted by means of two
potentiometers which can be accessed after removing the extractable
front panel.
Transmission levels are calibrated at the factory. For this reason, they
should only be adjusted when absolutely necessary (e.g. to eliminate
Larsen feedback). In these cases, turn the volume adjustment
potentiometer outwards to avoid worsening acoustic balance.
To adjust external volume:
Turn the potentiometer shown clockwise to turn the volume up and
anticlockwise to turn it down ( ).
To adjust internal volume:
Turn the potentiometer shown clockwise to turn the volume up and
anticlockwise to turn it down ( ).
•
•
•
•
SINTHESI STEEL PANELS
DOOR UNIT SET-UP MODULES
4
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
BUTTON MODULES
The following module versions are available:
With 1 button Ref. 1158/11
With 2 buttons Ref. 1158/12
With 3 buttons Ref. 1158/13
With 4 buttons Ref. 1158/14
Ref.1158/13 Ref.1158/14
Ref.1158/11 Ref.1158/12
DESCRIPTION OF TERMINALS
~12
}
Button and name tag light LED power
~0
U4 Call button 4 (Ref. 1158/14 only)
U3 Call button 3 (Ref. 1145/13 and Ref. 1145/14 only)
U2 Call button 2 (Ref. 1145/12, Ref. 1145/13 and Ref.
1145/14 only)
U1 Call button 1
G/T Call button common
G/T2 Button contact 2 (*) (Ref. 1145/12, Ref. 1145/13 and Ref.
1145/14 only)
G/T3 Button contact 3 (*) (Ref. 1145/13 and Ref. 1145/14 only)
G/T4 Button contact 4 (*) (Ref. 1145/14 only)
(*) These terminals are usually short-circuited and may be separated
by the installer.
CALL BUTTON CONTACT SEPARATION
Proceed as shown below to separate the G/T common contacts in
button modules Ref. 1158/12, Ref. 1158/13 and Ref. 1158/14 and in
door unit module Ref. 1158/22:
•
•
•
•
SINTHESI STEEL PANELS
BUTTON MODULES
Either groups or buttons or single buttons may be isolated according to
the point where the contacts are separated. Use the specic terminals
according to the separation employed to connect the buttons.
C
B
A
G/T4
C
U4
G/T3
B
U3
G/T2
A
U2
U1
G/T
Modules with 2 and 3 buttons (Ref. 1158/22, Ref. 1158/12 and Ref.
1158/13) will be equipped only with the terminals referred to the
buttons on the device. The button separation and connection methods
are the same in all cases.
BUTTON MODULE WIRING
To make wiring operations easier, the button modules are provided
with pre-cabled wires for the connection of the lighting circuits and
for the connection of the call buttons common wire.
Yellow
(~0, ~12)
Blue
(G/T)
sec.2i
−−−−
5
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
NAME TAG REPLACEMENT
There are different types of name tags provided:
White: for provisional writing with a felt-tip pen
Anthracite: for engraving
Red: for staircase light button (door unit set-up modules
only)
Proceed as follows to insert the name tags in the specic housing:
Remove the frame (if installed) and remove the extractable front.
Fit the name tags.
Reposition the extractable front.
1
2
Final engraved name holder.
Dummy transparent name holder.
3
•
•
•
1.
2.
3.
SPECIAL MODULES
The following special modules are available:
Repertory modules Ref. 1158/50
Blank modules Ref. 1158/59
DDA module with voice messages Ref. 1158/47
Hearing impaired people module Ref. 1158/48
REPERTORY MODULES Ref. 1158/50
Repertory modules are normally used to indicate the house number or
contain other information.
Power terminals ~0 and ~12 to light the unit via LEDs.
The procedure for tting repertory tags is the same as that for the
name tags.
Dummy transparent name holder.
Final engraved name holder.
BLANK MODULES Ref. 1158/59
This module is used to ll in spaces which are not used in modular
applications as required.
The same module can be used for other applications, e.g. burglar
alarms and automatic gates.
•
•
•
•
SINTHESI STEEL PANELS
SPECIAL MODULES
6
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
SINTHESI STEEL PANELS
SPECIAL MODULES
DDA MODULE WITH VOICE MESSAGES
Ref. 1158/47
The voice messages synthesis module with led Ref. 1158/47 allows
the user to know the system status by means of video and audio
signals.
This module allows to hard of hearing and partially sighted people to
access basic functions using the push button panel.
The system status is shown by the following indications:
call in progress: icon on RED and voice message “CALL IN
PROGRESS”
conversation in progress: icon on YELLOW
the door is open: icon on GREEN and voice message “DOOR
OPEN”
TECHNICAL CHARACTERISTICS
Power supply voltage 12 Vac or dc
Max. current consumption 150 mA @ 12 Vdc
200 mA @ 12 Vac
Voice messages acoustic pressure 80 dB a 10 cm
Operating temperature range -5 ÷ +45 °C
PROGRAMMING AND ADJUSTMENTS
Connector for
connection to digital
systems with
provided cable
Terminal pins
for connection
to analog systems
Terminal pins for
power supply with
dedicated transformer
Programming
dip-switch
Voice message
volume adjustment
System type setting:
Analog system (4+n, coax, 1+1, 5 wires)
Digital system (Bibus, Ipervoice, 2Voice) (default)
1.
2.
3.
Languages of voice messages can be selected with the other 3 dip-
switches:
Italian
English
(default)
French
German Spanish Greek
Polish
TERMINAL PINS DESCRIPTION
~12
}
12Vac or 12Vdc power supply
~0
C1 call tone input/output
SN call tone input/output
9/5 door lock release command input
F audio command input for 1+1 and 5-wire systems
1A audio command input for 4+n and coax systems
- ground reference
DOOR LOCK RELEASE DEVICES INSTALLATION
If it is needed to install devices used to activate the electric lock or
other electric loads, follow the procedure below:
Remove the module front panel
x the device used to activate the electric lock to the provided
holed front panel.
For further details on installation modes, see the instruction
manuals provided with products.
•
•
sec.2i
−−−−
7
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
HEARING IMPAIRED PEOPLE MODULE
Ref. 1158/48
ILA (Induction Loop Antenna) T-coil module Ref. 1158/48 allows hard
of hearing to hear door unit audio conversations with the hearing aid.
The hearing aid must be equipped with a T-magnetic interface.
Set the
switch to
T mode
Module with
door unit
T-Coil
module for
hard of
hearing
people
Button
module
20cm max.
TECHNICAL CHARACTERISTICS
Power supply voltage 12 Vac or dc
Max. current consumption 100 mA @ 12 Vdc
200 mA @ 12 Vac
Operating temperature range -5 ÷ +45 °C
SINTHESI STEEL PANELS
SPECIAL MODULES
INSTALLATION
Door unit
Ref.1145/500
Door unit
Ref.1145/67
12Vdc or Vac
power supply
~0 ~12
Camera unit module
with door unit
Ref.1758/91
TERMINAL PINS DESCRIPTION
~12
}
12Vac or 12Vdc power supply
~0
]
ILA ILA two terminal pins to be connected to ILA terminal
A power supply device dedicated to Ref. 1158/48 module is
needed.
8
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
CAMERA UNIT MODULES
The following camera unit module versions are available:
Ref. 1758/40 Ref. 1758/49 Ref. 1758/91
Systems with coaxial
cable
yes yes yes
5-wire systems
yes yes no
embedded door unit
no no yes
call buttons
0 0 1
colour camera
yes yes yes
CCIR version (50 Hz)
yes no yes
EIA version (60 Hz)
no yes no
TECHNICAL SPECIFICATIONS
Power voltage: 18 Vdc
Maximum uptake: 250 mAdc
Image sensor: 1/3” CCD
Lens: standard
Shutter: standard
Focus: xed
Minimum light for a good image: 0,2 lux
Coax video output: 1 Vpp composite
5-wire video output: 1 Vpp differential
Operating temperature range: -10 ÷ 50 °C
IMAGING ANGLES
0,8 m
0,9 m
1,0 m
85°
1,0 m
1,7 m 1,7 m
120°
Vertical
Horizontal
Ref. 1758/40 AND Ref. 1758/49 CAMERA
The cameras are composed by a single Sinthesi Steel module provided
with a camera with embedded lens and shutter and leds used to light
up the subject. These devices can be used both in systems with
coaxial cable and in 5-wire systems.
(default)
A - B
5-wire system
V3 - V5
System with
coaxial cable
Camera leds off
Camera leds on
DESCRIPTION OF TERMINALS
V3 Video signal for systems with coaxial cable
V5 Video signal ground for systems with coaxial cable
R1 Camera power negative
+TC Camera power positive
A
}
Video signal for 5-wire systems
B
T Camera power-on drive in digital systems
R2 Camera power supply positive signal in digital systems
SINTHESI STEEL PANELS
CAMERA UNIT MODULES
sec.2i
−−−−
9
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
Ref. 1758/91 CAMERA
Ref. 1758/91cameras are composed by a single Sinthesi Steel module
provided with a camera with embedded lens and shutter, leds used to
light up the subject, embedded door unit and one call button. Thanks
to these devices, a single module can contain a complete coaxial
video door phone push button panel.
(default)
Camera leds on
Camera leds off
Adjust the
sound volume
From ILA module
Ref. 1158/48
A
B
DESCRIPTION OF TERMINALS
R1 Camera power negative
+TC Camera power positive
V3 Video signal
V5 Video signal earth
~12
}
Name tag lighting LED power
~0
GT Call button common
GT2
}
Do not use
U2
U1 Column call
+ Door unit power positive
L Call feedback LED input
2 Audio in (from microphone to door phone)
- Door unit power negative
1 Traditional audio out (from speaker to door phone)
1A Electronic audio out (from speaker to door phone)
VOLUME ADJUSTMENTS
Volume can be adjusted both ways (internal and external) by means of
two potentiometers which can be accessed after opening the push-
button panel frame.
To adjust external volume turn the potentiometer clockwise to turn
the volume up and anticlockwise to turn it down.
To adjust internal volume turn the potentiometer clockwise to turn
the volume up and anticlockwise to turn it down.
Transmission level calibration is optimal. You are advised to
adjust the volume only if required to avoid disrupting the acoustic
balance using the potentiometer which adjusts the external
volume only.
SINTHESI STEEL PANELS
CAMERA UNIT MODULES - METAL FLUSH-MOUNTING BOXES
METAL FLUSH-MOUNTING BOXES
Four different versions of ush-mounting boxes for Sinthesi range
products are provided according to the number of modules to be
housed:
For 1 module (H = 118 mm) Ref. 1158/41
For 2 modules (H = 208 mm) Ref. 1158/42
For 3 modules (H = 298 mm) Ref. 1158/43
For 4 modules (H = 388 mm) Ref. 1158/44
All the ush mount boxes are installed at a depth of 45 mm and have
a width of 118 mm.
System wires lead into the boxes through the openings on the sides
and bottom of the box.
All openings are shut by removable closures.
1
2
ALTO
TOP
HAUT
1,55 ÷ 1,60 m
ALTO
TOP
HAUT
ALTO
TOP
HAUT
max.
6 mm
Apply the adhesive labels on the frame screw holes before
installing the box.
JOINING FLUSH-MOUNTING BOXES
The ush mount boxes are assembled by means of special spacers
provided with the ush mount boxes for 2, 3 and 4 modules, that are
also used as grommets.
Any number of ush-mounting boxes may be tted if no accessories
are used.
All shims are hollow to allow the passage of wires from one box to
the other.
ALTO
TOP
HAUT
1
2
ALTO
TOP
HAUT
3
ALTO
TOP
HAUT
ALTO
TOP
HAUT
•
•
•
•
10
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
PLASTIC FLUSH-MOUNTING BOXES
Four different versions of plastic ush-mounting boxes range products
are provided according to the number of modules to be housed:
• For 1 module Ref. 1145/51
• For 2 modules Ref. 1145/52
• For 3 modules Ref. 1145/53
• For 4 modules Ref. 1145/54
The ushing depth for all boxes is 45 mm.
System wires lead into the boxes through the openings on the sides
and bottom of the box.
All openings are shut by removable closures.
Two fairlead shims for joining the boxes are provided with ush-
mounting boxes for 2, 3 and 4 modules.
JOINING FLUSH-MOUNTING BOXES
Flush-mounting boxes may be joined by means of shims which double
as fairleads.
Any number of ush-mounting boxes may be tted if no accessories
are used.
All shims are hollow to allow the passage of wires from one box to
the other.
SINTHESI STEEL PANELS
PLASTIC FLUSH-MOUNTING BOXES - FRAMES AND MODULE HOLDERS
FRAMES AND MODULE HOLDERS
1, 2, 3 and 4 module versions of the module holders and frames are
available.
Glossy stainless steel frames have aesthetic and protection functions
and must be placed at the end of installation.
Module holders on the other hand are used for simple, immediate
fastening of Sinthesi Steel modules.
A hinge is provided in the lower part of the frame to tip the modules
and facilitate wiring and adjustments.
Available versions are:
• For 1 module Ref. 1158/61
• For 2 modules Ref. 1158/62
• For 3 modules Ref. 1158/63
• For 4 modules Ref. 1158/64
MODULE HOLDER INSTALLATION
Arrange the module holder and fasten the lower screw after ush
mounting the box. Raise the frame and fasten the upper screw.
Ref. 1158/41
Ref. 1158/42
Ref. 1158/43
Ref. 1158/44
Ref. 1145/51
Ref. 1145/52
Ref. 1145/53
Ref. 1145/54
sec.2i
−−−−
11
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
SINTHESI STEEL PANELS
FLUSH-MOUNTED PANEL ACCESSORIES
FRAME INSTALLATION
When the push button panel installation has been completed, x the
frame by tightening the screws with the provided key.
FLUSH-MOUNTED PANEL ACCESSORIES
RAIN HOOD WITH WALL COVER FRAME
The rain hoods are useful to make the panel installation
weatherproof.
The following versions of hoods to be tted between module holder
and wall are provided:
• For 1 module Ref. 1158/611
• For 2 modules Ref. 1158/612
• For 3 modules Ref. 1158/613
• For 4 modules Ref. 1158/614
157mm
H
50mm
H is 152 - 242 - 332 - 422 mm for 1, 2, 3 and 4 module versions,
respectively.
• For 4 modules (2 frames for 2 joined modules) Ref. 1158/624
• For 6 modules (2 frames for 3 joined modules) Ref. 1158/626
286mm
H
50mm
H is 242 - 332 mm for 2 and 3 module versions, respectively.
RAIN HOOD INSTALLATION
Embed the ush mounting box in the wall, position the waterproof
hood and fasten the module holder lower screws.
Ref. 1158/41
Ref. 1158/42
Ref. 1158/43
Ref. 1158/44
Ref. 1145/51
Ref. 1145/52
Ref. 1145/53
Ref. 1145/54
12
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
WALL-MOUNTED PANEL ACCESSORIES
CASE AND HOOD WITH FRAME AND MODULE
HOLDER
Wall-mounted installation is possible for vertical panels arrangements
only.
Cases and hoods protect the panel from the weather and may be
used for installation on walls without ush-mounted parts.
The following versions are provided (with frame and module holder):
For 1 module Ref. 1158/311
For 2 modules Ref. 1158/312
For 3 modules Ref. 1158/313
For 4 modules Ref. 1158/314
79mm157mm
H
H is 152 - 242 - 332 - 422 mm for 1, 2, 3 and 4 module versions,
respectively.
CASE AND HOOD INSTALLATION
Fasten the hood to the wall by means of four bolts.
1,55 ÷ 1,60 m
•
•
•
•
•
SINTHESI STEEL PANELS
WALL-MOUNTED PANEL ACCESSORIES
Install the module-holder frame on the enclosure
Fit the modules on the frame.
Turn the frame round and connect wires.
•
•
•
sec.2i
−−−−
13
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
SINTHESI STEEL PANELS
CONVERSATION PRIVACY DEVICE FOR “1+1” WIRE SYSTEMS
Close the module holder.
Fit the name tags.
Fit the frame.
•
•
•
CONVERSATION PRIVACY DEVICE FOR “1+1”
WIRE SYSTEMS Ref. 1158/74
The device is used for conversation privacy function in 1+1 door
phone systems and 5-wire video door phone systems only.
Each device has been designed to be installed on the buttons
modules with two provided screws, as described below; for system
connections, use the device terminal pins.
The device will only be partially used in the case of 1, 2 and 3 button
modules.
The number of boards consequently depends on the number of
buttons (from 1 to 4) on the panel.
When counting the number of boards required, remember that door
unit Ref. 1145/67 is already equipped with conversation privacy
devices for two users.
CONVERSATION PRIVACY DEVICE INSTALLATION
Installation on modules with 1 and 2 buttons
2
C1 (yellow)
C2 (blue)
U1
U2
1
Installation on modules with 3 and 4 buttons
1
2
3
DESCRIPTION OF TERMINALS
C1 Privacy circuit button 1
C2 Privacy circuit button 2
C3 Privacy circuit button 3
C4 Privacy circuit button 4
1 Power earth
4 Audio input
14
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
SINTHESI STEEL PANEL INSTALLATION
You are advised to install the modules at the heights shown below
according to the required system conguration.
1,55 ÷ 1,60 m 1,55 ÷ 1,60 m
In any case, consider the height shown in the gure for fastening the
camera for correct installation of complex arrangement with several
modules. The height refers to the door unit in door phone systems.
Thefollowingpicturesshowtheinstallationinmetalushmount
boxes; for installation in plastic ush mount boxes, see the
description of the single devices.
Arrange the hole (on the bottom or on the sides) for letting through
the connection wires before closing the ush-mounting box (single
or joined to other boxes).
1
2
ALTO
TOP
HAUT
Fit the ush mounting box in line with the wall: it must not project.
ALTO
TOP
HAUT
ALTO
TOP
HAUT
max.
6 mm
Apply the adhesive labels on the frame screw holes before
installing the box.
•
•
Fit the module holder frame.
Fit the modules in the frame.
Turn the frame round and connect wires.
Close the module holder.
Adjust correct perpendicularity of the panel.
•
•
•
•
•
SINTHESI STEEL PANELS
SINTHESI STEEL PANEL INSTALLATION
sec.2i
−−−−
15
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
Fit the name tags.
Dummy transparent name holder.
Final engraved name holder.
Fit the panel on the frame.
•
•
RECONDITIONING OF OLD SYSTEMS
(RETROFIT)
FRAME ADAPTER FOR K-STEEL FLUSH MOUNTING
BOX
The adapter boards are made to install Sinthesi Steel panels in K-Steel
model ush-mounting boxes without the need for masonry work.
Install the adapters between the module-holder frame and the old
ush mount box; they are provided in the following models:
For 1 module Ref. 1158/801
For 2 modules Ref. 1158/802
For 3 modules Ref. 1158/803
For installation, follow the procedure below:
Completely remove the K-Steel push button panel.
Fasten the adapter plate to the K-steel ush-mounting box by
means of the 4 screws provided.
Fix the module holder to the wall mounting frame
•
•
•
•
•
•
SINTHESI STEEL PANELS
RECONDITIONING OF OLD SYSTEMS (RETROFIT)
16
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
Fix the modules to the module holder and perform the
connections.
Close the module holder
Fit the panel on the frame.
•
•
•
INSTALLATION ON SINTHESI FLUSH MOUNT
BOXES
The installation on Sinthesi ush mount boxes doesn’t need any
adapter device. It is only suggested to use two screws in order to x
the module-holder frame:
Ref. 1145/51
Ref. 1145/52
Ref. 1145/53
Ref. 1145/54
SINTHESI STEEL PANELS
RECONDITIONING OF OLD SYSTEMS (RETROFIT)
INSTALLATION ON SINTHESI FLUSH MOUNT BOXES
sec.2i
−−−−
17
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS SINTHESI STEEL PANELS
FLUSH-MOUNTED VERSION
119mm 45mm
H1
125mm
H2
247mm 45mm
H1 H2
254mm
376mm 45mm
H1
H2
383mm
505mm 45mm
H1
H2
512mm
H2
641mm
H1
634mm
45mm
WALL-MOUNTED VERSION
157mm
H3
79mm
59mm
SINTHESI STEEL PANELS
DIMENSIONS
H3
For 1 module 152 mm
For 2 modules 242 mm
For 3 modules 332 mm
For 4 modules 422 mm
H1 H2
For 1 module 117 mm 127 mm
For 2 modules 207 mm 217 mm
For 3 modules 297 mm 307 mm
For 4 modules 387 mm 397 mm
18
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS
SINTHESI STEEL PANELS
4+n WIRE DOOR PHONE SYSTEMS
EXAMPLES OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
SINTHESI STEEL PANELS - 4+n WIRE DOOR PHONE SYSTEMS
4+n
BUTTONS NUMBER
1 2 3 4 5 6 7 8 9 10 11 11
h
12 12
h
13 13
h
14 14
h
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
Button modules
1158/13 1 1 1 1 1 1 1 1
1158/14 1 1 1 1 2 2 2 2 2 3 3 3 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7
Special modules 1158/50 1 1 1 1 1 1 1 1
Door unit
modules
1158/20 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1158/21 1 1 1 1 1 1 1 1 1
1158/22 1 1 1 1 1 1 1 1
Door unit 1145/500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Flush-mounting
box (*)
1158/41 1 1
1158/42 1 1 1 1 2 2 2 2
1158/43 1 1 1 1 2 2 2 2 2 2 2 2
1158/44 1 1 1 1 2 2 2 2 2 2 2
Module holders
and frames
1158/61 1 1
1158/62 1 1 1 1 2 2 2 2
1158/63 1 1 1 1 2 2 2 2 2 2 2 2
1158/64 1 1 1 1 2 2 2 2 2 2 2
Rain hood
1158/611 1 1
1158/612 1 1 1 1
1158/613 1 1 1 1
1158/614 1 1 1 1
1158/624 1 1 1 1
1158/626 1 1 1 1 1 1 1 1
Case with hood
(**)
1158/311 1 1
1158/312 1 1 1 1
1158/313 1 1 1 1
1158/314 1 1 1 1
4+n
BUTTONS NUMBER
30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62
Button modules
1158/13 1 1 3 3 1 1 1 1 1 3
1158/14 7 7 8 8 8 8 9 7 7 9 10 10 10 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15
Special modules
1158/50 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1158/59 1 1 1 1 1 1
Door unit
modules
1158/20 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1158/21 1 1 1 1 1 1 1 1
1158/22 1 1 1 1 1 1 1 1
Door unit 1145/500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Flush-mounting
box (*)
1158/43 3 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5
1158/44 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4
Module holders
and frames
1158/63 3 3 3 3 5 5 5 5 5 5 5 5 5 5 5 5
1158/64 2 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4
(*) Plastic boxes can also be used, according to the following code matching
Metal boxes
{
1158/41 ≡1145/51
}
Plastic boxes
1158/42 ≡1145/52
1158/43 ≡1145/53
1158/44 ≡1145/54
(**) Instead of products for ush mounting installation: ush mount boxes, frames and module-holder frames and rain hoods.
sec.2i
−−−−
19
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS
1 2 3 4 5 6 7 8 9 10
11 12 13 14
15 16 17
18 19 20
21 22 23
24 25 26
27 28 29 30 31
11h 12h 13h 14h
SINTHESI STEEL PANELS
4+n WIRE DOOR PHONE SYSTEMS
EXAMPLES OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
SINTHESI STEEL PANELS - 4+n WIRE DOOR PHONE SYSTEMS
20
−−−−
sec.2i
DOOR PHONE AND VIDEO DOOR PHONE SYSTEM: Product Technical Manual
PANELS
34 35
36 37 38 39
40 41 42 43
44 45 46 47
48 49 50
33
32
SINTHESI STEEL PANELS
4+n WIRE DOOR PHONE SYSTEMS
EXAMPLES OF MODULAR CONSTRUCTIONS WITH VARIOUS CAPACITIES
SINTHESI STEEL PANELS - 4+n WIRE DOOR PHONE SYSTEMS
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
urmet domus MT101-013 Technical Manual
- Category
- Door intercom systems
- Type
- Technical Manual
The urmet domus MT101-013 is a compact 2-wire handsfree video door phone that allows you to see and speak to visitors at your door from anywhere in your home. It features a 7-inch color LCD display, a built-in camera with night vision, and a sleek, modern design that will complement any home décor. With its easy-to-use interface and a variety of features, the urmet domus MT101-013 is the perfect way to enhance your home security and convenience.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
urmet domus MT124-013 Technical Manual
-
V-Tec MT101-013 Technical Manual
-
urmet domus MT124-027 Technical Manual
-
urmet domus MT124-027 Technical Manual
-
urmet domus MT101-013 Technical Manual
-
urmet domus MT124-013 Technical Manual
-
urmet domus MT124-012 Technical Manual
-
urmet domus MT124-013 Technical Manual
-
urmet domus MT101-013 Technical Manual
-
urmet domus MT124-027 Technical Manual
