urmet domus MT124-027 Technical Manual

Brand: urmet domus

Model: MT124-027

Category: Telephones

Type: Technical Manual

The urmet domus MT124-027 is a compact audio door entry system designed for single-family homes and small buildings. It features hands-free communication, allowing you to answer calls without picking up the handset. With its sleek and modern design, it seamlessly blends into any home décor. You can easily adjust the volume to your preference and even mute the ringer when needed. For added convenience, it comes equipped with a button for door lock release, granting access to visitors with just a press of a button.

sec.4b

−−−−

2 VOICE - Technical Manual

Download from www.urmet.com Technical Manuals area.

SECTION CONTENTS

2VOICE COMFORT DOOR PHONE REF. 1183/5 2

DESCRIPTION OF THE DEVICE.......................................................2

Structure .......................................................................................2

Description of terminals ................................................................2

Button functions ...........................................................................2

Led indications .............................................................................2

INSTALLATION .................................................................................3

TECHNICAL CHARACTERISTICS ....................................................3

Cleaning ........................................................................................3

DIP-SWITCH CONFIGURATION ......................................................3

Line terminal settings ...................................................................4

Performance .................................................................................4

Call reception ...............................................................................4

Answering a call ...........................................................................4

Adjusting the ringer speaker (mute) ..............................................4

Supplementary ringer ...................................................................4

Floor call .......................................................................................4

Intercom call forwarding ...............................................................4

Door open led ...............................................................................5

OPTIONALPROGRAMMING ............................................................5

Intercom function .........................................................................5

Call tone programming .................................................................5

Reset ............................................................................................5

KIT FOR TABLE MOUNTING Ref. 1150/50 ......................................6

SECTION 4B

(REV. C)

DOOR PHONE APARTMENT

STATIONS

2VOICE HAND-FREE DOOR PHONE REF. 1183/7 7

DESCRIPTION OF THE DEVICE.......................................................7

Structure .......................................................................................7

Description of terminals ................................................................7

Button functions ...........................................................................7

Led indications .............................................................................7

INSTALLATION .................................................................................8

TECHNICAL CHARACTERISTICS ....................................................8

Cleaning ........................................................................................8

DIP-SWITCH CONFIGURATION ......................................................9

Line terminal settings ...................................................................9

Performance ...............................................................................10

Call reception .............................................................................10

Answering a call .........................................................................10

Adjusting the ringer speaker (mute) ............................................10

Supplementary ringer .................................................................10

Floor call .....................................................................................10

Intercom call forwarding .............................................................10

Door open led .............................................................................10

OPTIONAL PROGRAMMING .........................................................10

Intercom function .......................................................................10

Call tone programming ...............................................................11

Door phone call ring tone ...........................................................11

Connection of a E2BP module to the

door phone

for the centralisation of lights and rollers ...................................11

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

2VOICE COMFORT DOOR PHONE Ref. 1183/5

DESCRIPTION OF THE DEVICE

Ref. 1183/5

2VOICE COMFORT DOOR PHONE Ref. 1183/5

1183/5) has a perfectly ﬂ at surface harmonized with the absence of

corners.

DESCRIPTION OF THE DEVICE

The main characteristics of door phone are the following:

microphone with speaker, electret microphone and spiral cable to

single telephone plug on base

backlit door opening button with green LED

3 additional buttons ( , , )

Multicolour indicator LED (mute, automatic door lock release,

open door, state of programming)

Conﬁ guration dip switch:

2 to deﬁ ne the station number in the apartment

8 to deﬁ ne the apartment number in the column

Refer to the paragraph “Dip-switch setup” how to set the

dip switches.

adjustable volume with mute function

differentiated door phone or ﬂ oor call with ﬁ ve different ring

tones

STRUCTURE

90 mm

52 mm

200 mm

1. Door opener button

2. Multicolour led

3. Buttons ( , , )

4. Terminal boards

5. Line termination Jumper

OFF ON

6. Conﬁ guration dip switch

•

–

•

DESCRIPTION OF TERMINALS

]

LINE

System bus connection

]

Floor call

S+

}

Call repeat

S-

BUTTON FUNCTIONS

STATE

BUTTON

STANDING

ON-HOOK

WAITING

FOR PICK-

(RECEIVING

CALL)

DURING

AUDIO

OPERATION

STANDING BY

OFF-HOOK

STATE OF

PROGRAMMING*

(ONLY WITH DOOR

PHONE STANDING

BY ON-HOOK)

Pedestrian

door lock

release

Pedestrian

door lock

release

Pedestrian

door lock

release

Pedestrian

door lock

release

Connect/Disconnect the

automatic door opening

system

Special

function

(default: 7)

Special

function

(default: 7)

Special

function

(default: 7)

Programmable

Intercom call 3

(Default; not

programmable

Adjust door phone

and floor call volume

(volume changes

according to the

following sequence:

HIGH, LOW, MUTE)

Special

function

(default: 8)

Special

function

(default: 8)

Special

function

(default: 8)

Programmable

Intercom call 2

(Default; not

programmable

Floor call ring

Tone (5 different ring

tones)

Driveway

door lock

release

Driveway

door lock

release

Driveway

door lock

release

Programmable

Intercom call 1

(Default; not

switchboard call

Door phone call ring

tone (5 different ring

tones)

(*) To enter and exit programming state, hold button pressed for

longer than 5 seconds. The yellow LED will blink slowly to indicate

that programming mode is selected. In any case, after 10 minutes

the system exits the programming state and saves the modiﬁ ed

parameters.

LED INDICATIONS

PRIORITY FUNCTIONS

Rapidly blinking red: mute on

Green blinking: automatic door opener on

Red on steady: main calling station door open

Slowly blinking red: secondary calling station door

open

Slowly blinking yellow: programming state on

Refer to the paragraph “Optional programming” for how to

program intercom calls.

2VOICE COMFORT DOOR PHONE

sec.4b

−−−−

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

2VOICE COMFORT DOOR PHONE Ref. 1183/5

INSTALLATION - TECHNICAL CHARACTERISTICS - DIP-SWITCH CONFIGURATION

INSTALLATION

To install door phone perform the following operations:

Remove the door phone cover

Fix the base to the wall with the provided screws and screw

anchors

Conﬁ gure the programming dip-switches

Connect the wires from the system to the terminal board

Mount again the cover

155 cm

(*)

(*) For disabled or special needs users of the D1 type (elderly), D2

type (lower limb motor difﬁ culties) or D3 type (upper limb motor

difﬁ culties), the centre of the device must be arranged at a height

comprised between 110 cm and 130 cm with respect to the ﬂ oor. For

more details, see technical standard CEI 64-21:2016-12 – Residential

environments. Systems suited for use by people with disabilities or

special needs..

TECHNICAL CHARACTERISTICS

Power supply voltage: ....................................................... 36 – 48 Vdc

Max. current consumption : in operation ....................... 70 mA max

in standby .......................... 3 mA max

Operating temperature : .............................................. -5 °C ÷ +45 °C

Max. humidity: ........................................................................90% UR

Dimensions (WxHxD): ............................................. 90 x 200 x 52 mm

CLEANING

You can clean the door phone by rubbing it gently with a damp

cloth.

DIP-SWITCH CONFIGURATION

OFF

INT

CODE

43215876

Default setting : default door phone settings are:

USER = 126

INDOOR STATION = 0

The dip switches must always be arranged in the correct setting

for correct operation of the system in this case.

CODE: user code

Use the CODE dip switches from 2 to 8 (2= most signiﬁ cant

bit - 8= least signiﬁ cant bit) to set the required code. Dip

switch 1 must be OFF.

•

2VOICE COMFORT DOOR PHONE

Ref. 1183/5

Set a number from 0 to 126 according to the following rules:

No two apartments in the system can have the same user code.

Indoor stations in parallel in the same apartment must have the

same user code

User codes be consecutive in the same column must.

•

CODE 3CODE 2CODE 1CODE 0

CODE 7CODE 6CODE 5CODE 4

CODE 11CODE 10CODE 9CODE 8

CODE 15CODE 14CODE 13CODE 12

CODE 19CODE 18CODE 17CODE 16

CODE 23CODE 22CODE 21CODE 20

CODE 27CODE 26CODE 25CODE 24

CODE 31CODE 30CODE 29CODE 28

CODE 35CODE 34CODE 33CODE 32

CODE 39CODE 38CODE 37CODE 36

CODE 43CODE 42CODE 41CODE 40

CODE 47CODE 46CODE 45CODE 44

CODE 51CODE 50CODE 49CODE 48

CODE 55CODE 54CODE 53CODE 52

CODE 59CODE 58CODE 57CODE 56

CODE 63CODE 62CODE 61CODE 60

CODE 67CODE 66CODE 65CODE 64

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

user in the same apartment. All the users indoor stations will ring at

the same time in the event of intercom calls to different apartments,

door unit calls and ﬂ oor calls.

The following considerations, should also be taken into account:

Extension 0 rings immediately when a call is received. Extensions

1, 2 and 3 will ring in sequence after each other.

LINE TERMINAL SETTINGS

A line terminal jumper (5) is ﬁ tted in the door phone. Activate the

terminal for devices wired at the end of a line from which another

section does not start from the device terminals (end of line).

PERFORMANCE

CALL RECEPTION

The user’s apartment station will ring with the programmed tone when

a call is received according to the source:

From main door unit

From secondary door unit

Intercom call

Floor calls

From switchboard

The electric lock can be operated from the calling door unit also

without picking up the handset when a call is received.

Indoor station 0 will ring immediately if there are several stations in

the apartment. Extensions 1, 2 and 3 will ring in sequence after each

other.

ANSWERING A CALL

Pick up the handset to establish a conversation with the door phone.

Hang up the handset to end the conversation and switch off the

display.

ADJUSTING THE RINGER SPEAKER (MUTE)

Hold button pressed for longer than 5 seconds; the yellow LED

will blink slowly to indicate that programming mode is selected.

In any case, after 10 minutes the system exits the programming

state and saves the modiﬁ ed parameters.

Press the button to change the ringer volume

Quit programming mode when the required level is set

(HIGH,LOW,MUTE).

The multicolour LED 2 will blink to indicate mute status.

SUPPLEMENTARY RINGER

The apartment stations are provided with a pair of terminals (S+, S-)

for connecting a supplementary ringer or relay. This ringer is controlled

when any call tone is generated.

FLOOR CALL

The indoor station is equipped with a pair of terminals (CP) for

connecting the ﬂ oor call button. The indoor station will ring with the

set tone for 3s when the button is pressed. Connect this button only

to one indoor station if there are several indoor stations in parallel.

Extensions 1, 2 and 3 will ring in sequence after each other.

INTERCOM CALL FORWARDING

After programming the button for the intercom function, pickup the

handset and press the button.

The following cases can occur according to the calling indoor station

state:

Indoor station free: the calling indoor station will output a

conﬁ rmation tone (2 beeps) and the called indoor station will ring.

Communication is established when the called user picks up.

Line / System busy: the indoor station outputs a warning tone (4

beeps in rapid sequence). Hang up and try again later.

•

CODE 71CODE 70CODE 69CODE 68

CODE 75CODE 74CODE 73CODE 72

CODE 79CODE 78CODE 77CODE 76

CODE 83CODE 82CODE 81CODE 80

CODE 87CODE 86CODE 85CODE 84

CODE 91CODE 90CODE 89CODE 88

CODE 95CODE 94CODE 93CODE 92

CODE 99CODE 98CODE 97CODE 96

CODE 103CODE 102CODE 101CODE 100

CODE 107CODE 106CODE 105CODE 104

CODE 111CODE 110CODE 109CODE 108

CODE 115CODE 114CODE 113CODE 112

CODE 119CODE 118CODE 117CODE 116

CODE 123CODE 122CODE 121CODE 120

CODE 126CODE 125CODE 124

(*) Conﬁ guration not allowed, available for future development.

INT: apartment station code

Set a number from 0 to 3 according to the following rules:

The indoor station code must be 0 if there is only one station in

the apartment.

Up to 4 apartment stations can be connected in parallel using the

same user code and different indoor station codes.

1 2

INT=0

1 2

INT=1

1 2

INT=2

1 2

INT=3

The indoor station code is used to identify the single stations of the

same user. This means that intercom calls can be address to the single

•

2VOICE COMFORT DOOR PHONE Ref. 1183/5

PERFORMANCE

Ref. 1183/5

2VOICE COMFORT DOOR PHONE

sec.4b

−−−−

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

DOOR OPEN LED

The function is only active for the last called door phone on which

the door opening button was pressed and corresponding to the last

calling door unit; see the “LED indications” for more details.

Open door function is available only if a suitable sensor has

been connected to the door unit.

OPTIONALPROGRAMMING

The following programming operations are needed after testing the

basic operation of the system, only if are required.

INTERCOM FUNCTION

Buttons ( , , ) can be programmed in 2Voice systems for intercom

call functions.

One button can be programmed to call another user in the column

or to call an indoor station in parallel. All indoor stations of the called

user will ring in the ﬁ rst case. Only the speciﬁ cally programmed indoor

station will ring in the second case.

INTERCOM FUNCTION BETWEEN VARIOUS USERS

Go to the indoor station to be programmed as caller (indoor station

A).

Hold the

button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Hold the button to be programmed pressed for at least three

seconds until the conﬁ rmation tone is heard.

Go to the user who will be called by pressing the button (user B)

and press the door opener button. The apartment stations will be

beep to indicate that they have been programmed.

Alternatively, go to a calling station and press the calling button

of user B. The indoor station being programming (A) will beep to

indicate that it has been programmed. The indoor stations of user

B will ring when this occurs. Ignore this call.

Hold the button pressed for longer than 5 seconds to quit

programming mode.

Check the programmed function: release the handset A and press

the programmed button. Check that all indoor stations of user B

ring and check reply audio.

You will need to program indoor station B to call A to make the

opposite call possible

INTERCOM FUNCTION IN THE SAME APARTMENT

Go to the apartment station to be programmed as caller (indoor

station C1).

Hold the button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Hold the button to be programmed pressed for at least three

seconds until the conﬁ rmation tone is heard.

Go to the apartment station that the button will call (apartment

station C2) and press the door opener button. The apartment

stations C1 and C2 will be beep to indicate that they have been

programmed.

Hold the button pressed for longer than 5 seconds to quit

programming mode.

Check the programmed function: release the handset C1 and

press the programmed button. Check that the apartment station

C2 rings and check audio.

You will need to program apartment station C2 to call C1 to make

the opposite call possible.

CALL TONE PROGRAMMING

In 2VOICE system each user can select the door phone call ring tone

and the ﬂ oor call ring tone among the 5 available ones.

DOOR PHONE CALL RING TONE

The selected call ring tone is the same for all door phone calls.

—

However, the call ring tone source can be identiﬁ ed thanks to the call

ring tone timing:

Call source Time Ring total duration

Main call station 3 s ON 3 s

Secondary call

station

0,4 s ON 0,2 s OFF for

5 times

2,8 s

Intercom

0,5 s ON 0,5 s OFF for

3 times

2,5 s

Switchboard

0,1 s ON 0,05 s OFF for 3

times pause 0,2 s repeated

for 5 times

2,8 s

FLOOR CALL RINGTONE

Hold the

button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Press to change the ring tone

When the call ring tone has been selected, exit the programming

state

The call ring tone is programmed

RESET

To restore default parameters of the device after entering programming

mode, hold button pressed for longer than 5 seconds, press the

and buttons together for longer than 3 seconds. The system will

emit two long beeps to conﬁ rm and exit the programming state.

•

2VOICE COMFORT DOOR PHONE Ref. 1183/5

OPTIONAL PROGRAMMING

2VOICE COMFORT DOOR PHONE

Ref. 1183/5

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

KIT FOR TABLE MOUNTING REF. 1150/50

The door phone can be table-mounted using a speciﬁ c transformation

kit Ref. 1150/50.

For installation, follow the procedure below:

1. Remove the door phone cover.

2. Fix the door phone base to the support

3. Insert the cable in the suitable hole and perform connections

The system cable must not be connected to the wiring

junction box provided with the table-top kit, but directly to

the door phone.

4. Block the cable to the support.

5. Close the door phone cover.

6. Mount the feet on the bottom side of the support.

2VOICE COMFORT DOOR PHONE Ref. 1183/5

KIT FOR TABLE MOUNTING Ref. 1150/50

Ref. 1183/5

2VOICE COMFORT DOOR PHONE

sec.4b

−−−−

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

2VOICE HAND-FREE DOOR PHONE

Ref. 1183/7

The Ref.1183/7 door phone is based on Urmet mechanical

design and offers all the functions of a door phone system in addition

to simple home automatic control using Yokis models.

DESCRIPTION OF THE DEVICE

The main characteristics of door phone are the following:

backlit door opening button with green LED

4 additional button ( , , , )

Multicolour indicator LED (mute, automatic door lock release,

open door, state of programming)

Conﬁ guration dip switch (SW1 – SW2):

n.1 of SW1, deﬁ nes the door phone operating mode: “Hands

Free”/Push to talk”;

n.2÷8 of SW1, deﬁ ne the apartment number in the column;

n.1÷2 of SW2, deﬁ ne the station number in the apartment;

Refer to the paragraph ”Dip-switch conﬁ guration”for how

to set the dip switches.

"Push to talk" function to activate two audio channels towards the

inside and the outside singularly;

adjustable volume with mute function;

differentiated door phone or ﬂ oor call with ﬁ ve different ring

tones;

bracket for ﬂ ush-mounting the device.

STRUCTURE

SW1 SW2

1. Microphone

2. Button see button function table

3. Button see button function table

4. Button to connect to Yokis devices; contacts X1, GT): max

50 mA - 12 Vdc

5. Button to connect to Yokis devices; contacts Y1, GT): max

50 mA - 12 Vdc

6. Multicolour indicator LED

7. Call and conversation speaker

8. Button used to activate/deactivate audio

9. Green LED under the Button

•

–

•

10.

Door opener button

11. Green LED under the button

12. Terminals for connecting to the system

13. Line termination jumper

ONOFF

14. Conﬁ guration dip switch (SW1 - SW2)

DESCRIPTION OF TERMINALS

GT Button common terminals

and

Y1 Button

X1 Button

S-

}

Supplementary ringer

S+

]

Floor call

]

LINE System BUS connection

BUTTON FUNCTIONS

State

Button

STAND-BY

WAITING

FOR PICK-UP

(RECEIVING

CALL)

DURING AUDIO

OPERATION

STAND-BY

AND

BUTTON

PRESSED

STATE OF

PROGRAMMING*

(ONLY WITH

DOOR PHONE IN

STAND-BY)

Pedestrian

door lock

release

Pedestrian

door lock

release

Pedestrian

door lock

release

Pedestrian

door lock

release

Connect/

Disconnect the

automatic door

opening system

---

Audio

activation

If pressed in the

operating mode:

A) “Hands Free”

ends the

conversation;

B) in “Push to talk”:

if pressed a

long time, it

enables the

audio of the

door unit;

if short pressed

it activates or

terminates the

conversation

—

---

Adjust door phone

and floor call

volume (volume

changes according

to the following

sequence: HIGH,

LOW, MUTE)

Special

function

(default: 7)

Special

function

(default: 7)

Special function

(default: 7)

Programmable

Intercom call 2

(Default; not

programmable

Floor call ring

Tone (5 different

ring tones)

Driveway

door lock

release

Driveway

door lock

release

Driveway

door lock

release

Programmable

Intercom call 1

(Default; not

switchboard

call)

Door phone

call ring tone

(5 different ring

tones)

(*) To enter and exit programming state, hold button pressed for

longer than 5 seconds. The yellow LED will blink slowly to indicate

that programming mode is selected. In any case, after 10 minutes

the system exits the programming state and saves the modiﬁ ed

parameters.

LED INDICATIONS

6. Multicolour indicator LED

PRIORITY FUNCTIONS

Rapidly blinking red: mute on

Green blinking: automatic door opener on

Red on steady: main calling station door open

Slowly blinking red: secondary calling station door open

Slowly blinking yellow: programming state on

2VOICE HAND-FREE DOOR PHONE Ref. 1183/7

DESCRIPTION OF THE DEVICE

2VOICE HAND-FREE DOOR PHONE

Ref. 1183/7

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

To save the programming, remember to exit from the same

by pressing the button for more then 5 seconds; in any

case, after 10 minutes the device exists the programming

state and saves the parameters changed.

9. Green LED under the button

On steady: call in progress

On blinking: conversation ongoing

10. Green LED under the

button

On steady: possibility of a door opening

INSTALLATION

WITH FLUSH-MOUNTED CASING MOD. 503

To install door phone perform the following operations:

Install ﬂ ush-mounting box at the height indicated.

Fix the bracket to the mounting box.

Box Mod. 503

Metal

bracket

(*)

1,55 m

n° 2 M3,5 x 19 mm

included

Connect the door phone

Fix the door phone to the bracket

WITH FLUSH-MOUNTED CASING Ø 60MM

Install ﬂ ush-mounting box at the height indicated.

Remove the plastic base from the door phone unit and ﬁ x the

base to the wall as shown in the drawing here below

1,55 m

n° 1 2,9 x 13 mm

countersunk screw

Box Ø 60 mm

n° 1 screw and screw

anchor included

(*)

Connect the door phone

Fix the door phone to its plastic base

•

WALL SURFACE MOUNTING

Remove the plastic base from the door phone unit and ﬁ x the base to

the wall as shown in the drawing here below.

n° 2 screws and screw

anchors included

1,55 m

(*)

Connect the door phone

Fix the door phone to its plastic base

DISTANCE BETWEEN HOLES

83,5 mm

Cable crossing area

(*) For disabled or special needs users of the D1 type (elderly), D2

type (lower limb motor difﬁ culties) or D3 type (upper limb motor

difﬁ culties), the centre of the device must be arranged at a

height comprised between 110 cm and 130 cm with respect to the

ﬂ oor. For more details, see technical standard CEI 64-21:2016-12

– Residential environments. Systems suited for use by people with

disabilities or special needs.

TECHNICAL CHARACTERISTICS

Power supply voltage: ...................................................... 36 – 48 Vdc

Max. current consumption: in operation ........................... 70 mA max

in standby: ....................................... 3 mA max

Operating temperature: ............................................... -5 °C ÷ +45 °C

Max. humidity: ........................................................................90% UR

Dimensions (WxHxD): ............................................. 110 x 80 x 18 mm

CLEANING

You can clean the door phone by rubbing it gently with a damp

cloth.

•

2VOICE HAND-FREE DOOR PHONE Ref. 1183/7

INSTALLATION - TECHNICAL CHARACTERISTICS

Ref. 1183/7

2VOICE COMFORT DOOR PHONE

sec.4b

−−−−

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

DIP-SWITCH CONFIGURATION

OFF

INT

CODE

43215876

Default setting: default door phone settings are:

CODE n.1 = OFF “Hands free” (default) / ON “Push to talk”;

CODE n.2-8 = 126

INT = 0

The dip switches must always be arranged in the correct setting

for correct operation of the system in this case.

CODE: user code

Use the CODE dip switches from 2 to 8 (2= most signiﬁ cant

bit - 8= least signiﬁ cant bit) to set the required code. Dip

switch 1 must be OFF.

Set a number from 0 to 126 according to the following rules:

No two apartments in the system can have the same user code.

Indoor stations in parallel in the same apartment must have the

same user code

User codes be consecutive in the same column must

•

CODE 3CODE 2CODE 1CODE 0

CODE 7CODE 6CODE 5CODE 4

CODE 11CODE 10CODE 9CODE 8

CODE 15CODE 14CODE 13CODE 12

CODE 19CODE 18CODE 17CODE 16

CODE 23CODE 22CODE 21CODE 20

CODE 27CODE 26CODE 25CODE 24

CODE 31CODE 30CODE 29CODE 28

CODE 35CODE 34CODE 33CODE 32

CODE 39CODE 38CODE 37CODE 36

CODE 43CODE 42CODE 41CODE 40

CODE 47CODE 46CODE 45CODE 44

CODE 51CODE 50CODE 49CODE 48

CODE 55CODE 54CODE 53CODE 52

CODE 59CODE 58CODE 57CODE 56

CODE 63CODE 62CODE 61CODE 60

CODE 67CODE 66CODE 65CODE 64

CODE 71CODE 70CODE 69CODE 68

CODE 75CODE 74CODE 73CODE 72

CODE 79CODE 78CODE 77CODE 76

CODE 83CODE 82CODE 81CODE 80

CODE 87CODE 86CODE 85CODE 84

CODE 91CODE 90CODE 89CODE 88

CODE 95CODE 94CODE 93CODE 92

CODE 99CODE 98CODE 97CODE 96

CODE 103CODE 102CODE 101CODE 100

CODE 107CODE 106CODE 105CODE 104

CODE 111CODE 110CODE 109CODE 108

CODE 115CODE 114CODE 113CODE 112

CODE 119CODE 118CODE 117CODE 116

2VOICE HAND-FREE DOOR PHONE Ref. 1183/7

DIP-SWITCH CONFIGURATION

2VOICE HAND-FREE DOOR PHONE

Ref. 1183/7

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

CODE 123CODE 122CODE 121CODE 120

CODE 126CODE 125CODE 124

(*) Conﬁ guration not allowed, available for future development.

INT: apartment station code

Set a number from 0 to 3 according to the following rules:

The indoor station code must be 0 if there is only one station in

the apartment.

Up to 4 apartment stations can be connected in parallel using the

same user code and different indoor station codes.

1 2

INT=0

1 2

INT=1

1 2

INT=2

1 2

INT=3

The indoor station code is used to identify the single stations of the

same user. This means that intercom calls can be address to the single

user in the same apartment. All the users indoor stations will ring at

the same time in the event of intercom calls to different apartments,

door unit calls and ﬂ oor calls.

The following considerations, should also be taken into account:

Extension 0 rings immediately when a call is received. Extensions

1, 2 and 3 will ring in sequence after each other.

LINE TERMINAL SETTINGS

A line terminal jumper (13) is ﬁ tted in the door phone. Activate the

terminal for devices wired at the end of a line from which another

section does not start from the device terminals (end of line).

PERFORMANCE

CALL RECEPTION

The user’s apartment station will ring with the programmed tone when

a call is received according to the source:

From main door unit

From secondary door unit

Intercom call

Floor calls

From switchboard

The electric lock can be operated from the calling door unit also

without picking up the handset when a call is received.

Indoor station 0 will ring immediately if there are several stations in

the apartment. Extensions 1, 2 and 3 will ring in sequence after each

other.

ANSWERING A CALL

Press the button to establish a conversation with the caller (the

button will start blinking as soon as it is pressed). Press the button

again to end the conversation and switch off the display.

ADJUSTING THE RINGER SPEAKER (MUTE)

Hold button pressed for longer than 5 seconds; the yellow LED

will blink slowly to indicate that programming mode is selected.

In any case, after 10 minutes the system exits the programming

state and saves the modiﬁ ed parameters.

Press the button to change the ringer volume.

Quit programming mode when the required level is set

(HIGH,LOW,MUTE).

The multicolour LED 6 will blink to indicate mute status.

With the MUTE function on, all beeps will be deactivated.

•

SUPPLEMENTARY RINGER

The door phone is equipped with a pair of terminals (S+, S-) for

connecting a supplementary ringer or a relay. This ringer is controlled

when any call tone is generated.

FLOOR CALL

The door phone is equipped with a pair of terminals (CP) for connecting

the ﬂ oor call button. If a ﬂ oor call is received, the door phone will

play the ring tone selected by the user. Connect this button to one

extension only if there are multiple apartment stations in parallel. The

apartment stations will ring in sequence.

INTERCOM CALL FORWARDING

After having programmed a button for the intercom function, press the

audio button and then press the programmed button.

The following cases can occur according to the calling indoor station

state:

Indoor station free: the calling indoor station will output a

conﬁ rmation tone (2 beeps) and the called indoor station will ring.

Communication is established when the called user picks up.

Line / System busy: the indoor station outputs a warning tone (4

beeps in rapid sequence). Hang up and try again later.

OPEN DOOR LED

The function is only active for the last called door phone on which

the door opening button was pressed and corresponding to the last

calling door unit; see the “LED indications” for more details.

Open door function is available only if a suitable sensor has

been connected to the door unit.

OPTIONAL PROGRAMMING

The following programming operations are needed after testing the

basic operation of the system, only if are required.

INTERCOM FUNCTION

Buttons , , can be programmed in 2Voice systems for intercom

call functions.

One button can be programmed to call another user in the column

or to call an indoor station in parallel. All indoor stations of the called

user will ring in the ﬁ rst case. Only the speciﬁ cally programmed indoor

station will ring in the second case.

INTERCOM FUNCTION BETWEEN VARIOUS USERS

Go to the indoor station to be programmed as caller (indoor station

A).

Hold the button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Hold the button to be programmed pressed for at least three

seconds until the conﬁ rmation tone is heard.

Go to the user who will be called by pressing the button (user B)

and press the door opener button. The apartment stations will be

beep to indicate that they have been programmed.

Alternatively, go to a calling station and press the calling button

of user B. The indoor station being programming (A) will beep to

indicate that it has been programmed. The indoor stations of user

B will ring when this occurs. Ignore this call.

Hold the button pressed for longer than 5 seconds to quit

programming mode.

Check the programmed function: release the handset A and press

the programmed button. Check that all indoor stations of user B

ring and check reply audio.

You will need to program indoor station B to call A to make the

opposite call possible.

•

—

2VOICE HAND-FREE DOOR PHONE Ref. 1183/7

PERFORMANCE - OPTIONAL PROGRAMMING

Ref. 1183/7

2VOICE COMFORT DOOR PHONE

sec.4b

−−−−

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

INTERCOM FUNCTION IN THE SAME APARTMENT

Go to the apartment station to be programmed as caller (indoor

station C1).

Hold the button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Hold the button to be programmed pressed for at least three

seconds until the conﬁ rmation tone is heard.

Go to the apartment station that the button will call (apartment

station C2) and press the door opener button. The apartment

stations C1 and C2 will be beep to indicate that they have been

programmed.

Hold the button pressed for longer than 5 seconds to quit

programming mode.

Check the programmed function: release the handset C1 and

press the programmed button. Check that the apartment station

C2 rings and check audio.

You will need to program apartment station C2 to call C1 to make

the opposite call possible.

ACTIVATING AUDIO BY PRESSING THE (PUSH TO TALK MODE)

BUTTON

If the communication between the calling station and the door phone

is disturbed, it is possible to activate the two audio channels (inwards

and outwards) individually.

After having received a call, short press to activate the audio from

the door unit, then if the

button is held pressed down, the audio

channel is activated externally and the user can speak to the caller.

To listen, it is necessary to press the button.

To end the conversation, shortly press button.

—

CALL TONE PROGRAMMING

In 2VOICE system each user can select the door phone call ring tone

and the ﬂ oor call ring tone among the 5 available ones.

DOOR PHONE CALL RING TONE

The selected call ring tone is the same for all door phone calls.

However, the call ring tone source can be identiﬁ ed thanks to the call

ring tone timing:

Call source Time Ring total duration

Main call station 3 s ON 3 s

Secondary call

station

0,4 s ON 0,2 s OFF for 5

times

2,8 s

Intercom

0,5 s ON 0,5 s OFF for 3

times

2,5 s

Switchboard

0,1 s ON 0,05 s OFF for 3

times pause 0,2 s repeated

for 5 times

2,8 s

FLOOR CALL RINGTONE

Hold the

button pressed for longer than 5 seconds. The yellow

LED will blink slowly to conﬁ rm that programming mode is

selected. In all cases, the device will quit programming mode and

save any changes after 10 minutes.

Press to change the ring tone

When the call ring tone has been selected, exit the programming

state

The call ring tone is programmed

RESET

To restore default parameters of the device after entering programming

mode, hold button pressed for longer than 5 seconds, press the

and buttons together for longer than 3 seconds. The system will

emit two long beeps to conﬁ rm and exit the programming state.

CONNECTION OF A E2BP MODULE TO THE

DOOR PHONE FOR THE CENTRALISATION OF

LIGHTS AND ROLLERS

MVR5

00ER

Tapparella

MVR5

00ER

ANTENNA

Tapparella

After suitably programming the Yokis devices, it will be

possible:

to activate the centralised closing of the rollers with a button

(for example );

a second button (for example ) will activate the turning off

of the lights.

For more information on YOKIS products, please visit

www.yokis.com

•

–

2VOICE HAND-FREE DOOR PHONE Ref. 1183/7

DIP-SWITCH CONFIGURATION

2VOICE HAND-FREE DOOR PHONE

Ref. 1183/7

−−−−

sec.4b

2 VOICE - Technical Manual

DOOR PHONE APARTMENT STATIONS

urmet domus MT124-027 Technical Manual

Brand: urmet domus

Model: MT124-027

Category: Telephones

Type: Technical Manual

Download PDF

report

urmet domus MT124-027 Technical Manual

urmet domus MT124-027 Technical Manual

Related papers

Other documents