JADEMAR LIGHTING JFL-PS User manual

Type
User manual

JADEMAR LIGHTING JFL-PS is a versatile and powerful floodlight series designed for various outdoor applications. With its durable construction and adjustable mounting options, it provides flexible illumination solutions for diverse needs. The JFL-PS series features high-quality LED lamps that deliver energy-efficient and long-lasting performance. Whether you're illuminating a backyard, parking lot, or sports field, this floodlight series offers reliable and efficient lighting.

JADEMAR LIGHTING JFL-PS is a versatile and powerful floodlight series designed for various outdoor applications. With its durable construction and adjustable mounting options, it provides flexible illumination solutions for diverse needs. The JFL-PS series features high-quality LED lamps that deliver energy-efficient and long-lasting performance. Whether you're illuminating a backyard, parking lot, or sports field, this floodlight series offers reliable and efficient lighting.

DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
Please abide by country, regional and local law and regulaons when installing this fixture.
Please turn off the power before installaon or maintenance.
Proper earth grounding is required to ensure safety.
To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
Please wear gloves to avoid injury before installaon.
During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel
for an overhaul.
This light can be used for outdoor installaon.
Please check if there is any damage during shipping. If so, please contact manufacturer mely.
Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to
installaon steps.
JFL-PS 90W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WARNING
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 1 of 9
INSTALLATION INSTRUCTIONS
1. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - TRUNNION MOUNTING
Step 1: Pass the input wire of the fixture through the bracket (Figure 4);
Step 2: Fix the bracket (Figure 5).
Figure 4 Figure 5
Figure 13 Figure 14 Figure 15
3. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - UNIVERSAL BRACKET MOUNTING
Step 1: Separate the bracket with tool (Figure 13);
Step 2: Pass the input wire of the fixture through the bracket (Figure 14);
Step 3: Pass the input wire through the bracket and lock the bracket (Figure 15).
2. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - YOKE MOUNTING
Step 1: Take out the bracket; ghten the screws, and fix the bracket on the fixture (Figure 6).
Figure 6
WARNINGS
WIRING DIAGRAM
INSTALLATION INSTRUCTIONS
1. INSTALLATION INSTRUCTIONS OF LED LAMPS - TRUNNION MOUNTING
Step 1: Drill holes on the wall as shown (Figure 30);
Step 2: Knock the expansion bolts into the wall (Figure 31);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 32).
Noce: Adjustable angle is 0~+/-90° (Figure 32)
Figure 30 Figure 31 Figure 32
Figure 34Figure 33 Figure 35
2. INSTALLATION INSTRUCTIONS OF LED LAMPS - YOKE MOUNTING
Step 1: Drill holes on the wall as shown (Figure 33);
Step 2: Knock the expansion bolts into the wall (Figure 34);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 35).
Noce: Adjustable angle is 0~+/-180° (Figure 35)
3. INSTALLATION INSTRUCTIONS OF LED LAMPS - UNIVERSAL BRACKET 4 IN 1
Step 1: Remove the spare parts, the remaining parts as shown in Figure 39;
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wires correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the
pole (Figure 40);
Step 3: Loosen the fixing bolts and adjusng bolts, adjust fixture angle as per actual demands. Tighten adjusng bolt and fixing bolts aer the angle is confirmed
(Figure 40).
Noce: Adjustable angle is 0~+/-90° (Figure 40)
Figure 40Figure 39
Figure 26 Figure 27
Figure 24 Figure 25
4. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - YOKE MOUNT TO UNIVERSAL BRACKET MOUNT
Step 1: Take out the bracket; Tighten the screws, fix the bracket on the fixture (Figure 24);
Step 2: Separate the bracket with tool (Figure 25);
Step 3: Pass the input wire of the fixture through the bracket (Figure 26);
Step 4: Pass the input wire through the bracket and lock the bracket (Figure 27)..
JFL-PS 90W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 2 of 9
INSTALLATION INSTRUCTIONS
Figure 41
Figure 42 Figure 43
Figure 44
7. INSTALLATION INSTRUCTIONS OF LED LAMPS - UNIVERSAL BRACKET 4 IN 1
Step 1: Change the rubber plug on the Installaon bar to the A&DM bracket (Figure 41);
Step 2: Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable, make sure good protecon on wire connecon, and put the wire in
the DM bracket; close the side lid and ghten it, (Figure 42) then finish installaon.
Noce: Adjustable angle is 0~+/-90° (Figure 42)
Noce: Round pole should be with adapng plate (Figure 43).
Aenon: When the photocell funcon is
required, photocell should be installed on the
back of lamp; When its not required, shorng
cap should be installed on the back of lamp
(Figure 44)
Figure 45 Figure 46 Figure 47
8. COLOR TEMPERATURE ADJUSTMENT INSTRUCTIONS
Standard wire:
L/live wire: Black\Brown;
N/null wire: White\Blue;
Ground wire: Green\Yellow-green.
Step 1: Find the switch to adjust CCT (Figure 45);
Step 2: Light up the lamp, push aside the fixing piece to show the black buon, and adjust the color temperature by pressing the black buon (Figure 46);
Step 3: Once the color temperature is confirmed, return the fixing piece back to the original posion and ghten the screw to lock the fixing piece (Figure 47).
WARNING/AVERTISSEMENT
MIN 90 °C SUPPLY CONDUCTOR
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
LES FILS D’ALIMENTATION 90 °C MIN
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI
CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
JFL-PS 90W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 3 of 9
INSTALLATION INSTRUCTIONS
JFL-PS 150W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
Please abide by country, regional and local law and regulaons when installing this fixture.
Please turn off the power before installaon or maintenance.
Proper earth grounding is required to ensure safety.
To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
Please wear gloves to avoid injury before installaon.
During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel
for an overhaul.
This light can be used for outdoor installaon.
Please check if there is any damage during shipping. If so, please contact manufacturer mely.
Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to
installaon steps.
WARNING
WARNINGS
1. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - TRUNNION MOUNTING
Step 1: Pass the input wire of the fixture through the bracket (Figure 1);
Step 2: Fix the bracket (Figure 2).
2. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - YOKE MOUNTING
Step 1: Take out the bracket; ghten the screws, and fix the bracket on the fixture (Figure 3).
4. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - SLIP FITTER TO UNIVERSAL BRACKET MOUNTING
Step 1: Separate the bracket with tool (Figure 10);
Step 2: Pass the input wire of the fixture through the bracket (Figure 11);
Step 3: Pass the input wire through the bracket and lock the bracket (Figure 12).
3. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - UNIVERSAL BRACKET MOUNTING
Step 1: Separate the bracket with tool (Figure 4);
Step 2: Pass the input wire of the fixture through the bracket (Figure 5)
Step 3: Pass the input wire through the bracket and lock the bracket (Figure 6).
Figure 4 Figure 5 Figure 6
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 4 of 9
INSTALLATION INSTRUCTIONS
5. INSTALLATION INSTRUCTIONS OF LED LAMPS - TRUNNION MOUNT TO WALL PLATE
Step 1: Drill holes on the wall as shown (Figure 13);
Step 2: Knock the expansion bolts into the wall (Figure 14);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 15).
Noce: Adjustable angle is 0~+/-90° (Figure 15)
6. INSTALLATION INSTRUCTIONS OF LED LAMPS - YOKE MOUNT TO WALL PLATE
Step 1: Drill holes on the wall as shown (Figure 16);
Step 2: Knock the expansion bolts into the wall (Figure 17);
Step 3: Fix the fixture to the bracket and ghten the screws; connect the wires property and put them into juncon box (Figure 18).
Noce: Adjustable angle is 0-+/-180° (Figure 18)
7. INSTALLATION INSTRUCTIONS OF LED LAMPS - UNIVERSAL BRACKET
Step 1: Remove the spare parts, the remaining parts as shown in Figure 22:
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wires correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the
pole (Figure 23);
Step 3: Loosen the fixing bolts and adjusng bolts, adjust fixture angle as per actual demands. Tighten adjusng bolt and fixing bolts aer the angle is confirmed
(Figure 23).
Noce: Adjustable angle is 0~+/-90° (Figure 23)
8. INSTALLATION INSTRUCTIONS OF LED LAMPS - UNIVERSAL BRACKET SQUARE & ROUND POLE
Step 1: Change the rubber plug on the Installaon bar to the A&DM bracket (Figure 24);
Step 2: Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable, make sure good
protecon on wire connecon, and put the wire in the DM bracket; close the side lid and ghten it, (figure 25)
then finish installaon.
Noce: Adjustable angle is 0~+/-90° (Figure 25)
Noce: Round pole should be with adapng plate (Figure 26).
Aenon: When the photocell funcon is required,
photocell should be installed on the back of lamp;
When it's not required, shorng cap should be
installed on the back of lamp (Figure 27)
Standard wire:
L/live wire: Black\Brown;
N/null wire: White\Blue;
Ground wire: Green\Yellow-green.
JFL-PS 150W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 5 of 9
INSTALLATION INSTRUCTIONS
9. COLOR TEMPERATURE ADJUSTMENT INSTRUCTIONS
Step 1: Find the switch to adjust CCT (Figure 28);
Step 2: Light up the lamp, push aside the fixing piece to show the black buon, and adjust the color temperature
by pressing the black buon(Figure 29);
Step 3: Once the color temperature is confirmed, return the fixing piece back to the original posion and ghten
the screw to lock the fixing piece (Figure 30).
Waage Adjustable Instrucon
1. Unscrew the plug with screwdriver or coin (Figure 31)
2. Adjust the waage adjustable dial switch to different gear which match to corresponding waage (Figure 31) First gear please tum to E7, 2nd gear (full power)
please turn to I, 1st to 2nd gear refer to lower waage to full waage.
3. Please re-install the plug aer adjustment.
Note: Please turn off the power before adjust waage.
WARNING/AVERTISSEMENT:
MIN 90 °C SUPPLY CONDUCTORS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
LES FILS D'ALIMENTATION 90 °C MIN
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI
CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
JFL-PS 150W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 6 of 9
INSTALLATION INSTRUCTIONS
JFL-PS 300W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
DO NOT USE AN ELECTRIC GENERATOR TO TEST THE LAMP.
Please abide by country, regional and local law and regulaons when installing this fixture.
Please turn off the power before installaon or maintenance.
Proper earth grounding is required to ensure safety.
To avoid possibility of electrical shock or fire, the installer must be a licensed electrician.
Please wear gloves to avoid injury before installaon.
During or aer installaon, if there are situaons such as smoke, fire in the wires or lamps, please turn off the power immediately and nofy relevant personnel
for an overhaul.
This light can be used for outdoor installaon.
Please check if there is any damage during shipping. If so, please contact manufacturer mely.
Please read the installaon instrucon carefully to check whether all the accessories are complete. Aer confirmaon, then install the fixture according to
installaon steps.
WARNING
WARNINGS
WIRING DIAGRAM
1. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - TRUNNION TO YOKE MOUNTING
Step 1: Put the input wire of the light across the bracket. (Figure 7)
Step 2: Fix the bracket. (Figure 8)
Step 3: Take out the bracket; let the input wire go through the cover or the back cover of the light, then fix the cover and ghten the screws, fix the bracket on the
fixture. (Figure 9)
2. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - UNIVERSAL BRACKET
Step 1: Separate the bracket with tool. (Figure 10)
Step 2: Put input wire of the light across the bracket. (Figure 11)
Step 3: Let input wire go through the bracket and lock the bracket. (Figure 12)
3. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - TRUNNION TO WALL MOUNT
Step 1: Drill holes on the wall as shown. (Figure 16)
Step 2; Knock the expansion bolts into the wall (Figure 17)
Step 3: Connect the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box. (Figure 18)
Noce: Adjustable angle is 0~+/-90* (Figure 18)
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 7 of 9
INSTALLATION INSTRUCTIONS
5. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - YOKE MOUNTING TO WALL PLATE
Step 1: Drill holes on the wall as shown. (Figure 19)
Step 2: Knock the expansion bolts into the wall (Figure 20)
Step 3: Connect the fixture to the bracket and ghten the screws; connect the wires properly and put them into juncon box (Figure 21)
Noce: Adjustable angle is 0-+/-90* (Figure 21)
6. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - UNIVERSAL BRACKET
Step 1: Remove the spare parts, the remaining parts such as (Figure 22)
Step 2: Loosen the 4 locking bolts on the slip fier, connect the wire correctly and put the wire into pole. Then fasten the locking bolts between slip fier and the pole.
(Figure 23)
Step 3: Loosen the fixing bolts and adjusng bolts, align the fixture to required angle. Tighten adjusng bolt and fixing bolts aer the angle is confirmed. (Figure 23)
Noce: Adjustable angle is 0-+/-90° (Figure 23)
7. INSTALLATION INSTRUCTIONS FOR DIFFERENT BRACKETS - UNIVERSAL BRACKET SQUARE & ROUND POLE
Step 1: Change the rubber plug on the Installaon bar to the AM&DM bracket. (Figure 24)
Step 2: Fix the DM bracket to the square pole by bolt. Connect the power cable with pole cable. Make sure good protecon on the wire connecon, and put the wire
in the DM bracket; close the side lid and ghten it, (figure 25) then finish installaon.
Noce: Adjustable angle is O~+/-90° (Figure 25)
Noce: Round pole should be with adapng plate. (Figure 26)
Aenon: When the photocell funcon is required, photocell should be installed
on the back of lamp; When it's not required, shorng cap should be installed on
the back of lamp (Figure 27)
Figure 28
Standard wire:
L/live wire; Black\Brown;
N/null wire: White Blue;
Ground wire: Green Yellow-green
NOTES
Step 1. Waage Adjustable Instrucon Unscrew the plug with screwdriver or coin
Figure 28)
Step 2. Adjust the waage adjustable dial switch to different gear which match to
corresponding waage (Figure 28)
First gear please turn to 2nd gear please turn 3rd gear please turn to
4th gear (full power) please. turn 1st to 4th gear refer to lower waage to full
waage
Step 3. Please re-install the plug aer adjustment.
Note: Please turn off the power before adjusng waage
JFL-PS 300W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 8 of 9
INSTALLATION INSTRUCTIONS
WARNING/AVERTISSEMENT
WARNING/AVERTISSEMENT:
MIN 90 °C SUPPLY CONDUCTORS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
LES FILS D'ALIMENTATION 90 °C MIN
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI
CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
JFL-PS 300W FLOODLIGHT SERIES INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 06/2022
Page 9 of 9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

JADEMAR LIGHTING JFL-PS User manual

Type
User manual

JADEMAR LIGHTING JFL-PS is a versatile and powerful floodlight series designed for various outdoor applications. With its durable construction and adjustable mounting options, it provides flexible illumination solutions for diverse needs. The JFL-PS series features high-quality LED lamps that deliver energy-efficient and long-lasting performance. Whether you're illuminating a backyard, parking lot, or sports field, this floodlight series offers reliable and efficient lighting.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI