2. JADEMAR
  3. JLHBD Series
JLHBD Series

JADEMAR JLHBD Series User manual

  • I've gone through the installation instructions for the JADEMAR LIGHTING JLHBD Linear High Bay. This document details the necessary steps for safe and correct installation, covering various mounting methods, wiring requirements, and dimming capabilities. The document includes important warnings and cautions to be followed during installation and maintenance, and the required wiring connections, including the dimming wires. I'm ready to answer your questions.
  • What should I do before installing the fixture?
    Who should perform the installation?
    What should I do before wiring the fixture to the power supply?
    What type of wire connectors should be used?
INSTALLATION REQUIREMENTS
WARNING: Risk of electric shock and serious injury. SHUT OFF BREAKER AT PANEL BEFORE INSTALLING.
JLHBD LINEAR HIGH BAY INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 01/2022
Page 1 of 3
INSTALLATION INSTRUCTIONS
WARNING:
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and
instrucons included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing roune maintenance upon this equipment, follow these general precauons.
• Commercial installaon, service and maintenance of luminaries should be performed by a qualified licensed electrician.
• For the installaon: If you are unsure about the installaon or maintenance of the luminaries, consult a qualified licensed electrician and check your local
electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installaon.
WARNING:
• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaries label informaon.
• All wiring connecons should be capped with UL approved wire connectors.
CAUTION:
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children
• Risk of burn. Disconnect power and allow fixture to cool before changing bulb or hanging fixture.
NOTICE: Green ground screw provided in proper locaon. Do not relocate.
NOTICE: Minimum 90° supply conductors
NOTICE: Specificaons and dimensions subject to change without noce.
NOTICE: Suitable for Dry or Damp locaon.
1.0 GENERAL WIRING DIAGRAM
Black(Line)
White(Neutral)
Green(Grd)
Purple(Dim+)
Grey(Dim-)
Blue(-)
Red(+)
Dimming wire
to 0-10v IEC
compliant control
Lead wire to
LED load
flexible metallic conduit flexible metallic conduit
2.0 INSTALLATION INSTRUCTIONS - CABLE KIT
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 01/2022
Page 2 of 3
INSTALLATION INSTRUCTIONS
4.0 INSTALLATION INSTRUCTIONS - WIRE GUARDS
6.0 INSTALLATION INSTRUCTIONS - PENDANT HANGER
3.0 INSTALLATION INSTRUCTIONS - CHAIN KIT
5.0 INSTALLATION INSTRUCTIONS - SURFACE MOUNTING
7.0 INSTALLATION INSTRUCTIONS - MOUNTING
1. As shown in the picture, turn counterclockwise
to unscrew the plug. 2. Insert the microwave sensor into the hole and ghten
it clockwise
JLHBD LINEAR HIGH BAY INSTALLATION INSTRUCTIONS
8.0 INSTALLATION INSTRUCTIONS - GENERAL WIRING DIAGRAM
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 01/2022
Page 3 of 3
INSTALLATION INSTRUCTIONS
• Remove the new LED fixture from packaging and inspect for any damages. Handle new LED fixture with care.
• CHAIN MOUNT EXAMPLE: Install the chain into the provided wire hanger. Secure the other end of the chain to a structure using hardware rated for the load.
Install the wire hanger onto the side of the top ETLB6 LED channel. Make sure the wiring hangers are fully engaged into the side holes on the top channel.
• Connect the LED high bay wiring to line wire, black to black, white to white and green to green. Use only UL listed wiring.
◦NOTE: Purple and grey lead inside the driver compartment are 0-10V (low voltage) dimming leads. Connect to dimming low voltage wiring only.
• Clean all residues/fingerprints from the new LED high bay and lens. Double check all hanging hardware before moving onto the next installaon.
INSTALLATION STEP:
*ALWAYS TURN OFF THE POWER SUPPLY FROM MAIN CIRCUIT BREAKER FIRST!*
JLHBD LINEAR HIGH BAY INSTALLATION INSTRUCTIONS
/