2. JADEMAR
  3. JBL CPS Square

JADEMAR JBL CPS Square User manual

  • Hello! I've reviewed the installation instructions for the JADEMAR JBL-CPS series CCT & Power Selectable Bollard. This document covers everything you need to know for the proper installation of the bollard, from site preparation to wiring and dial switch settings. I'm ready to assist with any questions you may have about the installation process or the device itself.
  • What should I do before beginning the installation?
    What is the purpose of the anchor bolt carrier?
    How do I access the dial switches?
• Risk of electric shock--Disconnect power to equipment before installing or servicing.
• This equipment must be installed according to all applicable codes & ordinances.
• Installaon and service of this equipment must be performed by qualified service personnel.
• Read these instrucons before installing, servicing or maintaining this equipment.
• Save these instrucons for maintaining and servicing.
• The installer must ensure that the foundaon is stable and can support the luminaires weight.
• The Installer must use proper means to secure the luminaire to the ground.
WARNING BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.
JBL-CPS SERIES
INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 07/2023
Page 1 of 2
FOR
HAZLOC
1.0 INSTALLATION INSTRUCTIONS - PREPARATION & INSTALLATION
JBL-CPS SERIES CCT & POWER SELECTABLE BOLLARD
Step 1: Remove the luminaire (Figure 1) and accessories (Figure 2) from the carton and
inspect luminaire for damage. Do not install a damaged luminaire.
• Edges may cut--wear gloves while handling or servicing this equipment.
• Inspect equipment for damage from shipping and handling.
• Recommended cleaning substances:
▪Wipe off dust with a dry, so cloth. Remove greasy spots etc. with a so cloth dampened in lukewarm water (<122°F/ 50°C) with a mild detergent.
▪Never use detergents containing abrasives and solvents.
▪Warning: Scouring powder and similar substances will scratch surfaces.
CAUTION RISK OF FIRE, ELECTRIC SHOCK, INJURY OR PROPERTY DAMAGE
Step 2: Prepare site. Get the anchor bolt carrier assembled as (Figure 3) and use it to
determine placement of anchor bolts in concrete. Ensure that concrete base is suitable for
the bollard load. Install three anchor bolts into concrete as per aached drawing, having at
least 1-1/2~2” protruding from concrete with threads free and clear of debris and dirt.
(Figure 4)
Step 3: Dis-assembly the fixture by loosening the set screws x4 with hex wrench. (Figure 5)
Lay the fixture down by the side of the installed anchor bolts. Keep the wires connected.
(Figure 6)
Step 4: Place bollard base plate over anchor bolts and ghten nuts securing the base plate
to the foundaon. As the wires shown on (Figure 7) will not be disconnected during
installaon, so please double check to make sure they are in good connecon aer the
base installaon.
Figure 6 Ground
hex wrench
L
N
G
Dim-
Dim+
5 Port Terminal Block
Ground Supply Wire
Support Bracket (12inches)
Concrete Base
(by others)
Electrical Conduit
(by others)
Figure 7
Ground
Anchor Bolt
Anchor Bolt Carrier
Nut
Flat Washer
Spring Washer x3
Figure 2
Bollard Fixture
Figure 1 Figure 4
1-1/2~2”
Figure 3
Figure 5
2.0 INSTALLATION INSTRUCTIONS - BOLLARD ANCHOR BOLT GUIDE
Step: 5 Put back the fixture body, and ghten the set screws x3 with hex wrench. (Figure 8)
Figure 10
Supply Line
Supply Neutral
Supply Ground
0-10V Dim+
Black Wire
LED BOLLARD
0-10V Dim-
White Wire
Green Wire
Purple Wire
Gray Wire
DIAL SWITCHES DIAGRAM
WIRING DIAGRAM
JBL-CPS SERIES
INSTALLATION INSTRUCTIONS
WWW.JADEMAR.COM
Miami, FL USA - info@jademar.com
T: 305.640.0465 - F: 305.640.0468 Revised 07/2023
Page 2 of 2
FOR
HAZLOC
JBL-CPS SERIES CCT & POWER SELECTABLE BOLLARD
Figure 9
Dial Switches for Wa & CCT Selecon
Labels
12W
16W
22W
3000K
4000K
5000K
Loosen 4 screws,
open the top of the fixture
/