DIODE LED Proximity Sensor Switch Installation guide

Brand
DIODE LED
Model
Proximity Sensor Switch
Type
Installation guide
1 OF 4 IG022218-1.0
PROXIMITY SENSOR SWITCH INSTALLATION GUIDE
®PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
SKU DI-SWTH-PRX
Input 12 - 24VDC Constant Voltage
Output 12 - 24VDC Constant Voltage
Max Load 12V 60W (5A), 24V 96W (4A)
Ambient
Temp
†-4° - 122°F (-20° - 50°C)
1. Install in accordance with national and local electrical
code regulations.
2. This product is intended to be installed and serviced by
a qualied, licensed electrician.
3. Do not modify or disassemble this product beyond
instructions or the warranty will be void.
4. Do not submerge, or install within 5 feet of a swimming
pool.
5. Only install with a Listed Class 2 DC LED driver.
6. To avoid Voltage Drop, ensure wire gauge used with
LED Strip Light is sufcient to keep under 3% voltage
drop.
7. DO NOT connect directly to high voltage power.
8. Only install compatible 12V and 24VDC constant
voltage luminaires.
9. This product is rated for indoor installation and is not
protected against moisture.
10. Failure to follow safety warnings, and installation
instructions will void the warranty for this product.
SAFETY & WARNINGS QUICK SPECS / MODELS
† Do not install product in environment outside listed
temperature.
POWER SUPPLY
CLASS
2
VOLTAGE DROP
LIMIT
3%
®
PROXIMTY SENSOR SWITCH
2
3
1
SENSOR
INPUT
V−
V+
V+
V−
POWER
INPUT
OUTPUT
TO LOAD
DI-SWTH-PRX
DRY LOCATION
24VDC
12VDC
2 OF 4 IG022218-1.0
PROXIMITY SENSOR SWITCH INSTALLATION GUIDE
®PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
1. Appropriate Junction Box
2. Class 2 rated Driver
3. PROXIMITY SENSOR SWITCH
4. LED Tape Light
REQUIRED TOOLS
1
2
3
1. Phillips-head Screwdriver
2. 7/16 inch Drill Bit
3. Wire Stripper
AC IN
DC OUT
L
G
N
V
−
V+
+
−
REQUIRED COMPONENTS
1
2
3
4
INSTALLATION
TURN POWER OFF AT CIRCUIT
BREAKER
SHOCK HAZARD! May result in serious
injury or death.
Turn power OFF at circuit breaker prior to
installalation.
DETERMINE LOCATION TO INSTALL
COMPONENTS
*NOT FOR USE IN SUBMERSIBLE
APPLICATIONS, OR WITHIN 5 FEET OF A
SWIMMING POOL.
Refer to SYSTEM DIAGRAMS
WIRE GAUGE & VOLTAGE DROP
Ensure appropriate wire is installed between driver,
xture, and any controls in between. When choosing
wire, factor in voltage drop, amperage rating, and type
(in-wall rated, wet location rated, etc.)
For more information, refer to system diagrams and
voltage drop charts at the end of this document.
®
PROXIMTY SENSOR SWITCH
2
3
1
SENSOR
INPUT
V−
V+
V+
V−
POWER
INPUT
OUTPUT
TO LOAD
DI-SWTH-PRX
1
2
3 OF 4 IG022218-1.0
PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
Loosen Nut
7/16 inches
(10mm)
Insert
Tighten Nut
PROXIMITY SENSOR PLACEMENT
a. Using a 7/16 inch Drill Bit, create a hole where
you would like to place the Sensor.
b. Loosen Nut from the Proximity Sensor.
c. Insert Proximity Sensor into 7/16 inch hole.
d. Tighten Nut onto back of Proximity Sensor.
INSTALLATION (CONT.)
CONNECT PROXIMITY SENSOR TO
SWITCH
Ensure the Connector is facing correctly when inserted
into Switch.(shown below)
WIRE DRIVER & LUMINAIRE TO
SENSOR SWITCH
5/16 in.
(8 mm)
b. Wire Class 2 driver and LED luminaire to Sensor
Switch. See SYSTEM DIAGRAM.
a. Strip wires.
Loosen with Phillips-
head screwdriver and
insert wire. Then
tighten terminal screw.
DI-SWTH-PRX
®
OCCUPANCY SENSOR SWITCH
2
3
1
SENSOR
INPUT
V−
V+
V+
V−
POWER
INPUT
OUTPUT
TO LOAD
TURN POWER ON AT CIRCUIT BREAKER
3
4
5
6
4 OF 4
®Toll Free: 877.817.6028 | Fax: 415.592.1596 | www.DiodeLED.com | info@DiodeLED.com
© 2015 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG022218-1.0
PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
PROXIMITY SENSOR SWITCH
INSTALLATION GUIDE
SYSTEM DIAGRAM
OPERATION
On Whenever there is no object within
the Sensor range.
Off Whenever an object enters the
Sensor range.
Sensor Range < 2.3 inches
Sensory Angle 60°
Diameter for
Drilling 7/16 inch Drill Bit. (10mm)
<2.3” >2.3”
OFF ON
Prior to troubleshooting, turn power OFF at circuit breaker
and verify all connections.
TROUBLESHOOTING
Symptom Common Cause
Luminaire
does not
illuminate
• Incorrect wiring.
• Polarity of Low Voltage V+ and V- are
reversed.
• Circuit breaker is OFF or tripped.
• Incorrect voltage pairing of dimmer and
luminaire. 12V drivers models will not
power a luminaire with a higher voltage
rating.
• Connecting the Sensor Switch to a
second Controller may result in a
delayed response time.
Luminaire
heats up
excessively
• Incorrect voltage pairing of driver and
luminaire. Do not attach a 12V luminaire
to a 24V driver.
• Luminaire is not compatible.
• Refer to luminaire install guide warnings
and safety tips.
PROXIMITY SENSOR SWITCH SPEC SHEET
For full specications.
CONSTANT VOLTAGE DRIVER SPEC SHEET
& INSTALL GUIDE
For full specications and installation instructions.
LED TAPE LIGHT SHEET & INSTALL GUIDE
For full specications and installation instructions.
ADDITIONAL RESOURCES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

DIODE LED Proximity Sensor Switch Installation guide

Brand
DIODE LED
Model
Proximity Sensor Switch
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents