Legrand FSP-221B-S-L2-W Installation guide

Brand: Legrand

Model: FSP-221B-S-L2-W

Type: Installation guide

Wattstopper

Low Voltage, High/Low/Off,

PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure

Basse Tension, Haut/Bas/Éteint

Luminaire avec détecteur IRP extérieur intégré dans un boitier IP66

Bajo Voltaje, Alto/Bajo/Apagado

Sensor exterior integrado del aplique PIR en gabinete IP66

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 22833 – 4/19 rev. 7

Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: FSP-201B, FSP-201B-S, FSP-201B-D

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Voltage ...............................................................12–32 VDC

Current Consumption ................................. 15 mA maximum

Wiring .......................................................................22 AWG

Length .......... 36” (91.44cm), 30” (76.2cm) from nipple

Primary Voltage .................................. +VDC, Com, Ctrl

Control Output .................................. 100 mA maximum

Dimming Voltage .................Dim + (violet), Dim - (gray)

Operating Temperature ..........-40°F (-40°C) to 167°F (75°C)

Tightening Skirt/Nut Torque ................................25–30 in-lbs

Dimensions

Collar ......................................1.30” diameter (33.0mm)

Collar height ..........................................0.64” (16.3mm)

Body .... 5.7”L x 2.3”W x 3.5”H (145mm x 60mm x 90mm)

Weight ...............................................................2.8 oz (80 g)

Enclosure .................................................IP66 (NEMA STD)

Coverage

FSP-L2 Lens @ 8’ height ................. up to 44’ diameter

FSP-L3 Lens @ 20’ height ............... up to 40’ diameter

FSP-L7 Lens @ 40’ height ............. up to 100’ diameter

Adjustments and Features

High Mode .................................................0 V – 10 V

Low Mode ......................................... 0 V – 9.8 V, Off

Time Delay .................... 30 seconds, 1 min –3 0 min

Cut Off ............... Disable, 1 min – 59 min ,1 hr – 5 hr

Sensitivity .................On-Fix, Off-Fix, Low, Med, Max

Hold Off Setpoint ......................Auto, None, 1–250 fc

Ramp Up .............................. Disable, 1 sec – 60 sec

Fade Down ........................... Disable, 1 sec – 60 sec

Photocell Setpoint for On/Off .......................1–250 fc

Factory Defaults

High Mode .......................................................... 10 V

Low Mode ............................................................ 1 V

Time Delay ........................................................5 min

Cut Off ................................................................. 1 hr

Sensitivity ...........................................................Max

Hold Off Setpoint ...........................................Disable

Ramp Up ........................................................Disable

Fade Down .....................................................Disable

Photocell Setpoint for On/Off .........................Disable

DESCRIPTION AND OPERATION

The FSP-201B is an IP66 rated motion sensor that dims lighting from

high to low based on movement.

Three configurations are available. The FSP-201B mounts inside the

fixture and the PIR lens connects to the FSP-201B through a 1.30”

diameter hole in the bottom of the fixture. The FSP-201B-S mounts to

a fixture/enclosure with a 1/2” knock out, via a nipple on the back. The

FSP-201B-D has a drop mount nipple, for mounting on to a pole, or to

a fixture.

The sensor uses passive infrared (PIR) sensing technology that reacts to

changes in infrared energy (moving body heat) within the coverage area.

Once the sensor stops detecting movement and the time delay elapses,

lights will go from high to low mode and eventually to an OFF position if

it is desired. Sensors must directly “see” motion of a person or moving

object to detect them, so careful consideration must be given to sensor

luminaire placement and lens selection. Avoid placing the sensor where obstructions may block the sensor’s line of sight.

The FSP-201B operates at 12–32 VDC. It is designed to be installed in indoor and outdoor environments.

NOTE: When the FSP-201B is powered up the first time, it will use factory default parameters to operate. If adjustments are needed,

the FSIR-100 configuration tool must be used.

LENS OPTIONS

Several lenses are available for use with the FSP-201B. Lenses give coverage at mounting heights between 8’–40’ for applications such

as, offices, warehouses and outdoor use. Density and range of the coverage is determined by the type of lens and mounting height.

A lens with shroud option is also available. The shroud blocks light coming from the fixture, to prevent interference with the photocell

function of the sensor. Lens modules are IP-66 rated when combined with an FSP-201B sensor mounted to an outdoor rated fixture.

See the FSP-Lx Coverage Guide for more information.

IR Receiver

IR Transmitte

Light Sensor

Motion Indicator

Red LED

PIR Sensor

Sensor Protection Cap

NOTE: Remove Cap before use

There are three configurations of the sensor:

• The FSP-201B mounts inside the fixture.

• The FSP-201B-S mounts to a fixture or an enclosure with a 1/2”

knockout.

• The FSP-201B-D mounts to a pole or fixture.

Mounting Inside the Fixture

1. Determine an appropriate mounting location inside the light fixture

minimizing the electric light contribution to the sensor’s photocell.

Allow a minimum distance of 0.2” (5.1mm) from the wiring end of the

sensor to the wall of the fixture.

2. Drill a hole 1.30” (33.0mm) in diameter through the sheet metal in the

bottom of the fixture.

3. Add the rubber gasket to the threaded collar, and install the sensor

face down, parallel to the mounting surface. Ensure the rubber gasket

touches the inside surface of the fixture. Install the tightening nut

securely against the fixture to a torque of 25–30 in-lbs to ensure IP

rating is maintained.

NOTE: An optional collar can be installed in place of the tightening nut on the FSP-201B. This collar is included with the

FSP-201B-S and FSP201B-D, as shown below.

Mounting to a Fixture/Enclosure–Straight Nipple

1. Determine an appropriate mounting location minimizing the electric light contribution

to the sensor’s photocell.

2. If there is no knockout, drill a hole 0.875” (22mm) in diameter through the sheet

metal in the fixture or enclosure.

3. Add the rubber gasket to the nipple, and install the sensor face down. Ensure the

rubber gasket touches the surface of the fixture. Install the nipple nut securely

against the fixture to a torque of 25–30 in-lbs to ensure IP rating is maintained.

Mounting to a Pole or Fixture–Drop Nipple

1. Determine an appropriate mounting location on the pole.

2. Drill a hole 0.875” (22mm) in diameter through the pole.

3. Add the rubber gasket to the nipple, and install the sensor face down. Ensure the

rubber gasket touches the surface of the fixture. If needed, add the nut between

the sensor body and the rubber gasket to ensure a secure fit. Install the nipple

nut securely against the fixture to a torque of 25–30 in-lbs to ensure IP rating is

maintained.

Completing the Installation

1. Align the locking features between the sensor and lens module and push the lens

module forward until the o-ring seals firmly. Turn the lens module clockwise to

ensure it locks in place.

2. Connect wires as shown in wiring diagram.

3. Restore power from the circuit breaker.

NOTE: The IP66 rating for this unit is based on proper installation as indicated above.

However, as Fixture housings may vary in thickness, material, and hole

dimensions to accommodate this unit, all precautions to maintain IP66 should be

considered with the combination and installation of the unit to the Fixture Housing.

This includes installation to an IP66 rated Fixture Housing and use of suitable

outdoor rated silicone seals or accessories.

Tightening Nut

(or Optional Collar)

Fixture

Wall

Lens Assembly

Outside

Fixture Wall

Inside Fixture

Wall

Mounting Within Fixture

Tightening Nut

(or Optional Collar)

Rubber

Gasket

Rubber

Gasket

NOTE: The Outside Fixture Wall thickness should be

no greater than 0.125” (3.18mm) for optimal

sensor mounting and security.

INSTALLATION

WARNING

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE SENSOR.

Straight Nipple Mount

Nipple

Rubber

Gaskets

Nipple

Nut

Drop Nipple Mount

Nipple

Nut

Nipple

Rubber

Gaskets

Drop Nipple Mount

Nipple

Rubber

Gaskets

Nipple

Nut

CAUTION

WATTSTOPPER RECOMMENDS ADDING A

20KA SURGE SUPPRESSOR TO PROTECT

THE FIXTURE, DRIVER AND FSP SENSOR.

WIRING

120 – 277 VAC (1

), 50/60 Hz

20A Ballast/ELV/MLV/Tungsten/LED

16A E-Ballast/CFL

1HP @ 120/240VAC

20A 120VAC Plug Load – Receptacle

Class 2 Output

24 VDC, 225 mA

BZ-200 Power Pack

UL 2043 Plenum Rated

16094r1

Appliance

Control

LISTED

88T9

Control

Common

+24VDC

Red

White

Neut.

Power Pack

Red

Black

Blue

Switch

Lighting

Load

Black

Any 3-Wire

24VDC

Sensor

Hot

Red

Ground

Green

Class 2

wiring only

+VDC (Red)

COM (Black)

CTRL (Blue)

Dim– (Gray)

Dim+ (V

iolet)

Non-Dimming

Ballast/Driver

Line (Black

)

Ground

(Green)

Neutral

(White)

www.legrand.us • 800.879.8585

120 – 277 VAC (1

), 50/60 Hz

20A Ballast/ELV/MLV/Tungsten/LED

16A E-Ballast/CFL

1HP @ 120/240VAC

20A 120VAC Plug Load – Receptacle

Class 2 Output

24 VDC, 225 mA

BZ-200 Power Pack

UL 2043 Plenum Rated

16094r1

Appliance

Control

LISTED

88T9

Control

Common

+24VDC

Red

White

Neut.

Power Pack

Red

Black

Blue

Switch

Lighting

Load

Black

Any 3-Wire

24VDC

Sensor

Hot

Red

Ground

Green

Class 2

wiring only

+VDC (Red)

COM (Black)

CTRL (Blue)

Neutral

(White)

Line (Black

)

Ground

(Green)

Dim– (Gray)

Dim+ (Violet)

Dimming

Ballast/Driver

www.legrand.us • 800.879.8585

+VDC Output (Red)

COM/GND (Black)

Neutral (White)

Line (Black)Ground (Green)

Dim– (Gray)

Dim+ (Violet)

Dim-to-Off

Ballast/Driver

(Blue)

Wiring with an

external DC

power supply

FSP-201B CONFIGURATION

The configuration process establishes the appropriate parameters for the FSP-201B

operation. This is done through the FSIR-100 configuration tool. If no configuration

steps are taken, the sensor will use its default parameter values.

USING THE FSIR-100 CONFIGURATION TOOL

The FSIR-100 Wireless IR Configuration Tool is a handheld tool for changing defaults

and testing of WattStopper FSP-201B. It provides wireless access to the FSP-201B

sensors for parameter changes and testing.

The FSIR-100 display shows menus and prompts to lead you through each process. The

navigation pad provides a simple way to navigate through the customization fields.

Within a certain mounting height of the sensor, the FSIR-100 allows modification of

the system without requiring ladders or tools; simply with a touch of a few buttons.

The FSIR-100 IR transceiver allows bi-directional communication between the

FSP-201B and the FSIR-100 configuration tool . Simple menu screens let you see

the current status of the sensor and make changes. It can change FSP-201B sensor

parameters such as high/low mode, sensitivity, time delay, cut off and more. With the

FSIR-100 you can also establish and store FSP-201B parameter profiles.

BATTERIES

The FSIR-100 operates on three standard 1.5V AAA Alkaline batteries or three rechargeable AAA NiMH

batteries. The battery status displays in the upper right corner of the display. Three bars next to BAT=

indicates a full battery charge. A warning appears on the display when the battery level falls below a

minimum acceptable level. To conserve battery power, the FSIR-100 automatically shuts off 10 minutes

after the last key press.

• If communication is not successful, (if possible) move closer to the sensor.

• If still not successful, there may be too much IR interference from other sources. Programming the unit

at night when there is no daylight available may be the only way to communicate with the sensor.

NAVIGATION

Navigate from one field to another using (up) or (down) arrow keys. The active field is indicated by

flashing (alternates) between yellow text on black background and black text on yellow background.

Once active, use the Select button to move to a menu or function within the active field. Value

fields are used to adjust parameter settings. They are shown in “less-than/greater-than” symbols:

<value>. Once active, change them using(left) and(right) arrow keys. The right key increments and

the left key decrements a value. Selections wrap-around if you continue to press the key beyond

maximum or minimum values. Moving away from the value field overwrites the original value. The

Home button takes you to the main menu. The Back button can be thought of as an undo function.

It takes you back one screen. Changes that were in process prior to pressing the key are lost.

NOTE: When you change parameter values on the FSP-201B, you need wait about 3 minutes

before the new parameters are saved into the memory.

FSP-2X1

HBP-111

Home/Main

Select

Down

Right/Next

Left

Back

Power

On/Off

BAT=

IR tx/rx

IR COMMUNICATION

IR communication can be affected by the mounting height of the sensor

and high ambient lighting such as direct daylight or electric light such as

floodlights, and some halogen, fluorescent lamps, LED’s.

When trying to communicate with the FSP-201B, be sure to be positioned

under the sensor without any obstructions. Every time the commissionng

tool establishes communication with the FSP-201B, the controlled load will

cycle.

TROUBLESHOOTING

Lights will not go to High Mode:

• Check all wire connections and verify the load and the ground wires are tightly secured.

• Make sure that the sensor is not obstructed.

• Check light level parameter, to find out the amount of light that the sensor is detecting. Cover the sensor lens to simulate darkness

in the room. If the lights come ON, the setpoint needs to be adjusted. If set for minimum, more than 1 fc at the sensor of ambient

light will cause the lights to be held OFF. See the new settings section for instructions.

• If lights still do not turn ON, call 800.879.8585 for technical support.

Lights will not go into Low Mode:

• The time delay can be set from a minimum of 30 seconds to a maximum of 30 minutes. Ensure that the time delay is set to the

desired delay and that there is no movement within the sensor’s view for that time period.

• To quickly test the unit operation, enable test mode and move out of the sensor’s view. Lights should fade to low mode after 5

seconds.

• If lights still do not fade to Low Mode, call 800.879.8585 for technical support

Lights will not turn OFF:

• Cut Off time may be set to “Disable.”

• Ensure that the Cut Off is set to the desired time and that there is no movement within the sensor’s view for that time period when

the lights are in Low Mode.

• To quickly test the unit operation, enable test mode and move out of the sensor’s view. Lights should fade to low mode after 5

seconds and then turn OFF (if cut off is enabled) after 10 sec.

• If lights still do not turn OFF, call 800.879.8585 for technical support.

False Triggering may occur if the sensor is exposed to high ambient temperature conditions and the unit is set to maximum sensitivity

for PIR detection.

• If this occurs, reduce the PIR sensitivity setting from maximum to a medium point and re-check unit operation.

• If experiencing false triggering during fade down/Off, try increasing the fade time.

Lights do not turn ON:

Check for blinking red LED. If the LED blinks twice, the sensor has reached its Hold Off setpoint, if the LED blinks 3 times, the sensor

has reached its Photocell Light Level setpoint.

Lights suddenly turn off and will not come back on:

Check for blinking red LED. If the LED blinks twice, the sensor has reached its Hold Off setpoint, if the LED blinks 3 times, the sensor

has reached its Photocell Light Level setpoint.

There is no IR communication:

Perform a power cycle on the FSP-201B.

OPERATION DURING POWER-UP

The first time the sensor is installed and powered, there will be 50 seconds of warm-up. The load will turn OFF after the warm up time if

no motion is detected.

15'-32'

* Distance may vary depending on the lighting environment

15'-32'

ORDERING INFORMATION

Catalog # Description

FSP-201B Single/ Dual Phase, PIR Fixture Integrated Sensor in IP66 Enclosure

FSP-201B-S Single/ Dual Phase, PIR Fixture Integrated Sensor in IP66 Enclosure, with Straight Nipple Mount

FSP-201B-D Single/ Dual Phase, PIR Fixture Integrated Sensor in IP66 Enclosure, with Drop Nipple Mount

FSIR-100 Configuration Tool

FSP-L2 360° lens, up to 44’ diameter at 8’ height

FSP-L2-S 360° lens, up to 44’ diameter at 8’ height, with shroud

FSP-L3 360° lens, up to 40’ diameter at 20’ height

FSP-L3-S 360° lens, up to 40’ diameter at 20’ height, with shroud

FSP-L7 360° lens, up to 100’ diameter at 40’ height

FSP-L7-S 360° lens, up to 100’ diameter at 40’ height, with shroud

FSP-C1 Small collar, for use with FSP-L2 and FSP-L3 lenses

FSP-C2 Large collar, for use with FSP-L7 lens

BZ-50 Power Pack: 120/277VAC, 50/60Hz, 20A ballast or incandescent

BZ-150 Power Pack: 120/277VAC, 50/60Hz, 20A ballast or incandescent, with Hold-On and Hold-Off

capability

BZ-200 Power Pack: 120/277VAC, 50/60 Hz, 20A Ballast/ELV/MLV/Incandescent/LED, 16A, E-Ballast/

CFL/Plug Load

BZ-250 Power Pack: 120/277VAC, 50/60 Hz, 20A, Ballast/ELV/MLV/Incandescent/LED, 16A E-Ballast/

CFL/Plug Load,

with Hold-On/Hold-Off capability

BZ-250-347 Power Pack: 120/347VAC, 50/60 Hz, 16A Ballast/ELV/MLV/Incandescent/LED/ E-Ballast/CFL,

15A Plug Load,

with Hold-On/Hold-Off capability

Sensor colors indicated by one of the following suffixes at the end of the catalog #:

-W = White; -BL = Black; -BR = Bronze/Brown; -G = Gray/Silver

Page is loading ...

800.879.8585

www.legrand.us/wattstopper

No. 22833 – 4/19 rev. 7

WattStopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of WattStopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

WattStopper garantit que ses produits sont

exempts de défauts de matériaux et de

fabrication pour une période de cinq (5) ans.

WattStopper ne peut être tenu responsable de

tout dommage consécutif causé par ou lié à

l’utilisation ou à la performance de ce produit

ou tout autre dommage indirect lié à la perte de

propriété, de revenus, ou de profits, ou aux coûts

d’enlèvement, d’installation ou de réinstallation.

WattStopper garantiza que sus productos están

libres de defectos en materiales y mano de obra

por un período de cinco (5) años. No existen

obligaciones ni responsabilidades por parte de

Legrand/WattStopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida de

propiedad, renta o ganancias, o al costo de

extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

Legrand FSP-221B-S-L2-W Installation guide

Brand: Legrand

Model: FSP-221B-S-L2-W

Type: Installation guide

Download PDF

report

in other languages

français: Legrand FSP-221B-S-L2-W Guide d'installation
español: Legrand FSP-221B-S-L2-W Guía de instalación

Legrand FSP-221B-S-L2-W Installation guide

Legrand FSP-221B-S-L2-W Installation guide

in other languages

Related papers

Other documents