Jackson 44S User manual

Jackson
Brand
Jackson
Model
44S
Category
Dishwashers
Type
User manual
CREWSERIES
RACKCONVEYORDISHMACHINES
With
WISR
TM
TECHNICALMANUAL
INSTALLATIONMANUALFOREXPORTUNITS
SERVICEMANUALFORDOMESTICUNITS
ELECTRICALLYHEATEDMODELS:
CREW44
CREW66
STEAMHEATEDMODELS
CREW44S
CREW66S
Feb.25,2011
P/N07610‐003‐78‐18(RevisionD)
JacksonWWS,Inc.
P.O.Box1060,Hwy25E
Barbourville,KYUSA
1.606.523.9795
www.jacksonwws.com
Revision
Letter
Revision
Date
MadeBy ApplicableECNs Details
A 07-27-10 CW/JC N/A Initial release of manual
B 02-25-11 JC 8183
8186
8187
8177
Transformer change for 208 Volt units.
Drain handle operation & alignment change.
Door splash shield addition.
Rinse paddle switch operation.
Initial release of 66” units, 44” Steam units &
66” Steam units
C 06-30-11 JC N/A Initial release of 23” & 30” unhooded side-
loaders
D 03-28-13 JC Changed Jackson Logo
TABLEOFCONTENTS
Speciications
MachineDimensions Page6
OperatingParameters Page12
NotesRegardingElectricalRequirements Page13
ElectricalRequirements Page14
SideLoaderDimensions Page10
SteamBoosterHeaterDimensions Page11
Instructions
InstallationInstructions Page17
CurtainInstallationInstructions Page22
OperatingInstructions Page23
DelimeInstructions Page25
Maintenance
Troubleshooting Page26
PartsSection
ControlBoxComponents Page27
Overloads Page29
MiscellaneousElectricalComponents Page30
WashHeaterandHeaterShroudAssemblies Page31
PumpSuctionAssembly Page32
WashHeaters Page33
DoorAssembly Page34
Pre‐WashDoorAssembly Page35
WashDoorSpringAssembly Page36
PlumbingAssembly,MainWaterInlet Page37
WashTankFillAssembly Page38
Pre‐WashTankFillAssemblies Page39
WashManifoldandArmAssembly Page40
Pre‐WashManifoldandArmAssemblies Page42
RinseAssembly Page44
PawlBarAssembly Page46
PawlBarBracketAssembly Page47
PawlBarGutterAssembly Page48
TABLEOFCONTENTS(CONTINUED)
PartsSection(Continued)
MiscellaneousParts Page54
VentilationCowlParts Page55
VentilationCowlforUnhoodedSide‐Loader Page56
DriveAssembly Page57
Side‐Loaders Page59
Side‐LoaderDriveLinkage Page62
SteamHeatingCoilAssembly Page63
BoosterHeaterOption(Electric) Page64
BoosterHeaterOption(Steam) Page65
RackPaddleAssembly Page49
Brackets Page53
Covers,GuardsandPanels Page52
RinsePaddleAssemblies Page50
DrainAssemblyParts Page51
ElectricalDiagramsandSchematics
BoosterHeaterSchematic(3Phase) Page67
BoosterHeaterSchematic(1Phase,12KW) Page68
BoosterHeaterSchematic(1Phase,18KW) Page69
TemperatureBoard Page71
Schematic,44”(208‐230‐460/60/3Phase) Page73
Schematic,44”(208‐230/60/1Phase) Page74
Schematic,Photo‐CellTableLimitSwitch Page72
Schematic,44”Steam(208‐230‐460/60/3Phase) Page75
Schematic,44”Steam(208‐230/60/1Phase) Page76
Schematic,66”(208‐230‐460/60/3Phase) Page77
Schematic,66”(208‐230/60/1Phase) Page78
Schematic,66”Steam(208‐230‐460/60/3Phase) Page79
Schematic,66”Steam(208‐230/60/1Phase) Page80
SteamBoosterHeaterSchematic Page70
Maintenance&RepairCentersPage81
6
PageCreated:06‐30‐2011
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
MACHINEDIMENSIONS(44”LefttoRight)
E1 MAINELECTRICALCONNECTION(1.375”DIAHOLE)
E2 BOOSTERHEATERELECT.CONNECTION(1.375”DIA)
W MAININLETWATERCONNECTION(1/2NPT‐F)
D DRAINCONNECTION(1‐1/2”NPT‐F)
DET DETERGENTBULKHEADACCESS(.875”DIAHOLE)
SAN** SANITIZERINLETTORINSE(1/8”NPT‐F)
RA RINSEAIDCONNECTIONTORINSE(1/8”NPT‐F)
CP CONDUCTIVITYPROBEACCESS(.875”DIAHOLE)
S* STEAMTOWASHTUBHEATINGCOIL(3/4”NPT‐F)
C* CONDENSATERETURN(3/4”NPT‐F)
V1 VENTILATIONDUCTCONN.(LOADEND)4”x16”ID
V2 VENTILATIONDUCTCONN.(UNLOADEND)4”x16”ID
34 in
67
1
2
in
71
5
8
in
51
1
2
in MIN
(NOTE 2)
11 in
21 in
23.50
14
1
2
in
6
1
8
in
10
1
8
in (NOTE 3)
3
8
in
8
3
4
in
61
1
8
in
63
5
8
in
64
1
2
in
TABLE to TABLE
44 in
63
3
8
in
93 in MAX
(NOTE 1)
34 in
20 in
20
5
8
in
14 in
16
1
2
in
30
1
2
in
E1
E2
W
V2
V1
S*
C*
D
CP
DET
CP
4 in
7
3
8
in
RA
SAN
E2
E1
W
23
3
4
in
23
3
4
in
23
3
4
in
3
3
4
in
17
1
8
in
DET
DET
S*
W
E2
E1
C*
SAN
2
1
4
in
RA
26
5
8
in
D
7
7
8
in
19
1
8
in
11
1
2
in
11
1
2
in
44
1
8
in
NOTE 2:
VENTILATION DUCT ADAPTERS ARE
ADJUSTABLE FROM 51-1/2" TO 54".
NOTE 1:
THE MAXIMUM DOOR HEIGHT MAY BE
REDUCED BY THE ADDITION OF OPTIONAL
DOOR BRACKETS. MAXIMUM HEIGHTS OF
91", 89" & 87" ARE AVAILABLE.
NOTE 3:
THE DRIVE ASSEMBLY AND GUARD
MAY BE INSTALLED ON EITHER END
OF THE UNIT. INSTALLATION ON THE
UNLOAD END IS STANDARD. IF
INSTALLED ON THE LOAD END,
PLEASE ENSURE ANY SCRAP SINKS
IN THE TABLING ARE AT AN ADEQUATE
DISTANCE TO PROVIDE FOR CLEARANCE
OF THE DRIVE ASSEMBLY.
15
1
4
in
21
1
2
in
14
7
8
in
NOTE 4:
ALL VERTICAL DIMENSIONS MAY
VARY DUE TO THE ADJUSTABLE
FEET.
(NOTE 4)
(NOTE 4)
(NOTE 4)
(NOTE 4)
4
3
8
in
* APPLIES TO STEAM HEATED UNITS
** CHEMICAL SANITIZING UNITS ONLY
7
PageCreated:06‐30‐2011
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
MACHINEDIMENSIONS(44”RighttoLeft)
63
5
8
in
64
1
2
in
61
1
8
in
71
5
8
in
67
1
2
in
15
1
4
in
9 in
8
3
4
in
11
1
2
in
11
1
2
in
6
1
8
in
14
1
2
in
21
1
8
in
23
5
8
in
11
1
8
in
4
1
4
in
7
3
8
in
23
3
4
in
23
3
4
in
51
5
8
in
(NOTE 2)
4
3
8
in
RA
3
8
in
2
1
4
in
7
7
8
in
19
1
8
in
14
7
8
in
21
1
2
in
26
5
8
in
4
3
8
in
TABLE to TABLE
44 in
63
3
8
in
93 in MAX
(NOTE 1)
34 in
23
3
4
in
3
3
4
in
17
1
8
in
20 in
20
5
8
in
14 in
30
1
2
in
16
1
2
in
W
E1
E2
DET
CP
S*
W
E2
E1
SAN
D
C*
S*
E1
E2
W
RA
SAN
DET
DET
S*
C*
D
CP
(NOTE 3) 10
1
8
in
(NOTE 4)
(NOTE 4)
(NOTE 4)
(NOTE 4)
NOTE 1:
THE MAXIMUM DOOR HEIGHT MAY BE
REDUCED BY THE ADDITION OF OPTIONAL
DOOR BRACKETS. MAXIMUM HEIGHTS OF
91", 89" & 87" ARE AVAILABLE.
NOTE 2:
VENTILATION DUCT ADAPTERS ARE
ADJUSTABLE FROM 51-1/2" TO 54".
NOTE 3:
THE DRIVE ASSEMBLY AND GUARD
MAY BE INSTALLED ON EITHER END
OF THE UNIT. INSTALLATION ON THE
UNLOAD END IS STANDARD. IF
INSTALLED ON THE LOAD END,
PLEASE ENSURE ANY SCRAP SINKS
IN THE TABLING ARE AT AN ADEQUATE
DISTANCE TO PROVIDE FOR CLEARANCE
OF THE DRIVE ASSEMBLY.
NOTE 4:
ALL VERTICAL DIMENSIONS MAY
VARY DUE TO THE ADJUSTABLE
FEET.
16 in
4 in
44
1
8
in
V2
V1
E1 MAINELECTRICALCONNECTION(1.375”DIAHOLE)
E2 BOOSTERHEATERELECT.CONNECTION(1.375”DIA)
W MAININLETWATERCONNECTION(1/2NPT‐F)
D DRAINCONNECTION(1‐1/2”NPT‐F)
DET DETERGENTBULKHEADACCESS(.875”DIAHOLE)
SAN** SANITIZERINLETTORINSE(1/8”NPT‐F)
RA RINSEAIDCONNECTIONTORINSE(1/8”NPT‐F)
CP CONDUCTIVITYPROBEACCESS(.875”DIAHOLE)
S* STEAMTOWASHTUBHEATINGCOIL(3/4”NPT‐F)
C* CONDENSATERETURN(3/4”NPT‐F)
V1 VENTILATIONDUCTCONN.(LOADEND)4”x16”ID
V2 VENTILATIONDUCTCONN.(UNLOADEND)4”x16”ID
* APPLIES TO STEAM HEATED UNITS
** CHEMICAL SANITIZING UNITS ONLY
8
PageCreated:06‐30‐2011
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
MACHINEDIMENSION(66”LefttoRight)
15
1
4
in
67
1
2
in
63
5
8
in
64
1
2
in
7
3
8
in
61
1
8
in
23
1
2
in
21 in
11
1
8
in
4
1
4
in
73
1
2
in MIN
(NOTE 2)
63
1
2
in
61 in
10
7
8
in
34 in
11
1
2
in
23
3
4
in
3
3
4
in
17
1
8
in
33
1
2
in
7
5
8
in
14
1
2
in
6
1
8
in
9 in
8
3
4
in
8
3
4
in
20
5
8
in
20 in
93 in MAX
(NOTE 1)
3
8
in
9 in
2
1
4
in
14
7
8
in
21
1
2
in
26
5
8
in
30
5
8
in
TABLE to TABLE
66 in
85
1
2
in
14 in
16
5
8
in
20
3
8
in
14
7
8
in
W2
W3***
W1
SAN**
D1
C*
S*
RA
D2
E1
E2
W3***
W2
E1
E2
W1
RA
SAN**
V1
V2
S*
DET
D1
C*
CP
D2
E1
E2
W1
CP
66
1
8
in
DET
16 in
4 in
71
5
8
in
10
1
8
in (NOTE 3)
NOTE 1:
THE MAXIMUM DOOR HEIGHT MAY BE
REDUCED BY THE ADDITION OF OPTIONAL
DOOR BRACKETS. MAXIMUM HEIGHTS OF
91", 89" & 87" ARE AVAILABLE.
NOTE 2:
VENTILATION DUCT ADAPTERS ARE
ADJUSTABLE FROM 73-1/2" TO 76".
NOTE 3:
THE DRIVE ASSEMBLY AND GUARD
MAY BE INSTALLED ON EITHER END
OF THE UNIT. INSTALLATION ON THE
UNLOAD END IS STANDARD. IF
INSTALLED ON THE LOAD END,
PLEASE ENSURE ANY SCRAP SINKS
IN THE TABLING ARE AT AN ADEQUATE
DISTANCE TO PROVIDE FOR CLEARANCE
OF THE DRIVE ASSEMBLY.
NOTE 4:
ALL VERTICAL DIMENSIONS MAY
VARY DUE TO THE ADJUSTABLE
FEET.
(NOTE 4)
(NOTE 4)
(NOTE 4)
E1 MAINELECTRICALCONNECTION(1.375”DIAHOLE)
E2 BOOSTERHEATERELECT.CONNECTION(1.375”DIA)
W1 MAININLETWATERCONNECTION(1/2NPT‐F)
W2 PRE‐WASHINLETWATERCONN.(1/2NPT‐F)
W3*** PRE‐WASHCOLDWATERCONN.(1/2NPT‐F)
D1 DRAINCONNECTION,WASH(1‐1/2”NPT‐F)
D2 DRAINCONNECTION,PRE‐WASH(1‐1/2”NPT‐F)
DET DETERGENTBULKHEADACCESS(.875”DIAHOLE)
RA RINSEAIDCONNECTIONTORINSE(1/8”NPT‐F)
CP CONDUCTIVITYPROBEACCESS(.875”DIAHOLE)
S* STEAMTOWASHTUBHEATINGCOIL(3/4”NPT‐F)
C* CONDENSATERETURN(3/4”NPT‐F)
V1 VENTILATIONDUCTCONN.(LOADEND)4”x16”ID
V2 VENTILATIONDUCTCONN.(UNLOADEND)4”x16”ID
SAN** SANITIZERINLETTORINSE(1/8”NPT‐F)
* APPLIES TO STEAM HEATED UNITS
** CHEMICAL SANITIZING UNITS ONLY
*** PRE-WASH COLD WATER THERMOSTAT OPTION ONLY
9
PageCreated:06‐30‐2011
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
MACHINEDIMENSION(66”RighttoLeft)
E1 MAINELECTRICALCONNECTION(1.375”DIAHOLE)
E2 BOOSTERHEATERELECT.CONNECTION(1.375”DIA)
W1 MAININLETWATERCONNECTION(1/2NPT‐F)
W2 PRE‐WASHINLETWATERCONN.(1/2NPT‐F)
W3*** PRE‐WASHCOLDWATERCONN.(1/2NPT‐F)
D1 DRAINCONNECTION,WASH(1‐1/2”NPT‐F)
D2 DRAINCONNECTION,PRE‐WASH(1‐1/2”NPT‐F)
DET DETERGENTBULKHEADACCESS(.875”DIAHOLE)
RA RINSEAIDCONNECTIONTORINSE(1/8”NPT‐F)
CP CONDUCTIVITYPROBEACCESS(.875”DIAHOLE)
S* STEAMTOWASHTUBHEATINGCOIL(3/4”NPT‐F)
C* CONDENSATERETURN(3/4”NPT‐F)
V1 VENTILATIONDUCTCONN.(LOADEND)4”x16”ID
V2 VENTILATIONDUCTCONN.(UNLOADEND)4”x16”ID
SAN** SANITIZERINLETTORINSE(1/8”NPT‐F)
* APPLIES TO STEAM HEATED UNITS
** CHEMICAL SANITIZING UNITS ONLY
*** PRE-WASH COLD WATER THERMOSTAT OPTION ONLY
15
1
4
in
73
1
2
in
(NOTE 2)
10
1
8
in (NOTE 3)
71
5
8
in
67
1
2
in
9 in
11
1
2
in
63
5
8
in
64
1
2
in
61
1
8
in
7
3
8
in
4
1
4
in
11
1
8
in
21 in
23
1
2
in
10
7
8
in
61 in
63
1
2
in
8
3
4
in
7
5
8
in
29
1
2
in
93 in MAX
(NOTE 1)
3
3
4
in
17
1
8
in
23
3
4
in
3
8
in
2
1
4
in
7
3
4
in
19
1
8
in
14
7
8
in
26
5
8
in
TABLE to TABLE
66 in
85
1
2
in
21
1
2
in
14 in
30
5
8
in
16
5
8
in
66
1
8
in
4
3
8
in
4 in
16 in
E2
E1
SAN**
RA W1
W2
W3***
D1
D2
S*
C*
SAN**
RA
W1
E2
E1
W2
W3***
S*
DET
C*
CP
D2
D1
CP
DET
W1
E1
E2
V2
V1
6
1
8
in
11
5
8
in
34 in
(NOTE 4)
(NOTE 4) (NOTE 4)
(NOTE 4)
NOTE 3:
THE DRIVE ASSEMBLY AND GUARD
MAY BE INSTALLED ON EITHER END
OF THE UNIT. INSTALLATION ON THE
UNLOAD END IS STANDARD. IF
INSTALLED ON THE LOAD END,
PLEASE ENSURE ANY SCRAP SINKS
IN THE TABLING ARE AT AN ADEQUATE
DISTANCE TO PROVIDE FOR CLEARANCE
OF THE DRIVE ASSEMBLY.
NOTE 2:
VENTILATION DUCT ADAPTERS ARE
ADJUSTABLE FROM 73-1/2" TO 76".
NOTE 1:
THE MAXIMUM DOOR HEIGHT MAY BE
REDUCED BY THE ADDITION OF OPTIONAL
DOOR BRACKETS. MAXIMUM HEIGHTS OF
91", 89" & 87" ARE AVAILABLE.
NOTE 4:
ALL VERTICAL DIMENSIONS MAY
VARY DUE TO THE ADJUSTABLE
FEET.
10
PageCreated:06‐30‐2011
Revised:N/A
Technical Manual (07610-003-78-18)
SIDE LOADER DIMENSIONS
23.00
29.00
30.32
23.00
29.00
30.32
16.35 16.35
10.00
34.00
+1.00
-1.00
10.00
34.00
+1.00
-1.00
22.00 22.00
ADJUSTABLE VENTILATION
DUCT ADAPTER
ADJUSTABLE VENTILATION
DUCT ADAPTER
SIDE-LOADER
DRAIN HOSE
SIDE-LOADER
DRAIN HOSE
23" L-R UNHOODED
SIDE-LOADER
23" R-L UNHOODED
SIDE-LOADER
VENTILATION SCOOP
VENTILATION SCOOP
VENTILATION COWL
WITH CUTOUT FOR
R-L UNITS
VENTILATION COWL
WITH CUTOUT FOR
L-R UNITS
DIMENSION IS 30.00" FOR THE
30" UNHOODED SIDE-LOADER
DIMENSION IS 30.00" FOR THE
30" UNHOODED SIDE-LOADER
ELECTRICAL
CONDUIT
ELECTRICAL
CONDUIT
11
PageCreated:06‐30‐2011
Revised:N/A
Technical Manual (07610-003-78-18)
STEAM BOOSTER HEATER DIMENSIONS
E MAINELECTRICALCONNECTION(7/8”DIAHOLE)
W1 MAININLETWATERCONNECTION(3/4NPT‐F)
W2 WATEROUTLETCONNECTION(3/4NPT‐F)
PW WATERPRESSURERELIEFOUTLET(3/4NPT‐F)
PS STEAMPRESSURERELIEFOUTLET(1”NPT‐F)
S STEAMSUPPLYTOBOOSTER(1”NPT‐F)
C STEAMCONDENSATECONNECTION(3/4NPT‐F)
20
3
4
in
2
7
8
in
17
1
2
in
24 in
14
5
8
in
33
1
8
in
8
7
8
in
8
5
8
in
S
PS
PW
C
S
W1
W2
C
10
1
8
in
PW
1
3
4
in
PS
W2
11
1
8
in
22 in
3
3
8
in
19
3
8
in
20
1
8
in
28
5
8
in
20
1
4
in
W1
S
W2
PS
PW
33.69
11
3
8
in
22 in
7
1
2
in
E
E
E
SteamConsumption
(lbm/hr)
30 37 45 52 59
TemperatureRise
(DegreesFahrenheit)
40 50 60 70 80
Based upon a Steam Inlet Pressure of 15-25psig
BOOSTER HEATER STEAM CONSUMPTION
12
PageCreated:05‐04‐2010
Revised:02‐25‐2011
TechnicalManual(07610‐003‐78‐18)
OperatingParameters
ModelDesignation:44”66”44”Steam66”Steam
OperatingCapacity:
RacksperHour218218218218
DishesperHour  3488348834883488
GlassesperHour 7848784878487848
TankCapacity(gallons):
WashTank 35.635.635.635.6
Pre‐WashTankN/A15.8N/A15.8
ElectricalLoads(asapplicable):
WashMotorHP 3.03.03.03.0
DriveMotorHP0.250.250.250.25
Pre‐WashMotorHPN/A2.0N/A2.0
WashHeaterKW15or1818N/AN/A
NOTE:Always refer to the machine data plate for speciic electrical and water requirements. The
materialprovidedonthispageisforreferenceonlyandissubjecttochangewithoutnotice.
HOTWATERSANITIZING
Water
Temperatures(Fahrenheit):
Pre‐WashTemperature(Recommended)N/A110‐140N/A110‐140
MinimumWashTemperature 160160160160
MinimumRinseTemperature 180180180180
IncomingWaterTemperature
12KWBooster 140140N/AN/A
18KWBooster 110110N/AN/A
NoBooster180180180180
CHEMICALSANITIZING
WaterTemperatures(Fahrenheit):
Pre‐WashTemperature(Recommended)N/A110‐120N/A
110‐120
MinimumWashTemperature 120120120120
MinimumRinseTemperature 120120120120
IncomingWaterTemperature
12KWBooster 8080N/AN/A
18KWBooster5050N/AN/A
NoBooster120120120120
OtherWaterRequirements:
WaterFlowPressure(PSIG) 15151515
FlowRateMinimum(GPM)1.181.181.181.18
WaterLineSize(NPT) 1/2”1/2”1/2”1/2”
DrainLineSize(NPT) 1‐1/2”1‐1/2”1‐1/2”1‐1/2”
SteamRequirements
SteamLineforWashTank(NPT)N/AN/A3/4”3/4”
SteamFlowPressure(PSIG)N/AN/A10‐2010‐20
Consumption@15PSIG(lbm/hr)N/AN/A6060
13
PageCreated:05‐04‐2010
Revised:02‐25‐2011
TechnicalManual(07610‐003‐78‐18)
NotesRegardingElectricalRequirements
Allelectricalratingsprovidedinthismanualareforreferenceonly.Alwaysrefertothemachinedataplate
togettheexactelectricalinformationforyourmachine.All electrical work performed on machines
shouldbedoneinaccordancewithapplicablelocal,state,territorialandnationalcodes.Workshould
onlybeperformedbyqualiiedelectriciansandauthorizedserviceagents.AlistofauthorizedServiceAgen‐
ciesislocatedinthebackofthismanual.
Note that all electrical wiring used in the dish‐machine must be rated, at a minimum, for 100C (212F).
Furthermore,usecopperconductorsonly.
Whereapplicable,heatingelementamperagedrawshavebeenadjustedfortheassumedinputvoltage.Jack‐
sonassumesincomingvoltageswillbeeither208,230or460volts.Someoftheheatingelementsusedin
ourmachinesareactuallyratedforothervoltages,suchas240 or 480volts. Alwaysverify the amperage
drawofthemachineinoperationwhensizingcircuitprotection.
Ifyourmachineisequippedwiththeoptionalrinseheater,notetherinseheaterhasitsownelectricalcon‐
nectionandthereforerequiresaseparateservice.Amperageloadsformotorsandheatersarecalledouton
themachinedataplatefortheinstallation/servicetechnician.
Theelectricalconigurationsofthemachinesareasfollows:
AvailableElectricalCharacteristics:
 208volt,60Hz,singlephase
 230volt,60Hz,singlephase
 208volt,60Hz,threephase
 230volt,60Hz,threephase
 460volt,60Hz,threephase
AvailableWashTankHeaters:
 15KW(standardforCREW44)
 18KW(optionalforCREW44,standardforCREW66)
AvailableRinseHeaters(“BoosterHeaters”):
 None(standard)
 12KW(40Friseintemperature)
 18KW(70Friseintemperature)
14
PageCreated:05‐04‐2010
Revised:02‐25‐2011
TechnicalManual(07610‐003‐78‐18)
ElectricalRequirementsfor44”Units
Volts PhaseFreq
Wash
Motor
Amps
Drive
Motor
Amps
Wash
Heater
Amps
FLA MCA MOP
208 1 60 10.0A 1.8A 72.1A 83.9A 86.4A 96.4A
230 1 60 10.0A 1.8A *59.9A 71.7A 74.2A 84.2A
208 3 60 8.6A 1.1A 41.6A 51.3A 53.5A 62.1A
230 3 60 8.4A 1.1A *34.6A 44.1A 46.2A 54.6A
460 3 60 4.2A 0.6A **17.3A 22.1A 23.2A 27.4A
240 1 60 10.0A 1.8A 62.5A 74.3A 76.8A 86.8A
480 3 60 4.2A 0.6A 18.1A 22.9A 24.0A 28.2A
240 3 60 8.4A 1.1A 36.1A 45.6A 47.7A 56.1A
44”with15kWWashHeater
Volts Phase Freq
Wash
Motor
Amps
Drive
Motor
Amps
Wash
Heater
Amps
FLA MCA MOP
208 1 60 10.0A 1.8A 86.5A 98.3A 100.8A 110.8A
230 1 60 10.0A 1.8A *71.9A 83.7A 86.2A 96.2A
208 3 60 8.6A 1.1A 50.0A 59.7A 61.9A 70.5A
230 3 60 8.4A 1.1A *41.5A 51.0A 53.1A 61.5A
460 3 60 4.2A 0.6A **20.8A 25.6A 26.7A 30.9A
480 3 60 4.2A 0.6A 21.7A 26.5A 27.6A 31.8A
240 3 60 8.4A 1.1A 43.4A 52.9A 55.0A 63.4A
240 1 60 10.0A 1.8A 75.0A 86.8A 89.3A 99.3A
44”with18kWWashHeater
Volts PhaseFreq
Wash
Motor
Amps
Drive
Motor
Amps
FLA MCA MOP
208 1 60 10.0A 1.8A 11.8A 14.3A 24.3A
230 1 60 10.0A 1.8A 11.8A 14.3A 24.3A
208 3 60 8.6A 1.1A 9.7A 11.9A 20.5A
230 3 60 8.4A 1.1A 9.5A 11.6A 20.0A
460 3 60 4.2A 0.6A 4.8A 5.9A 10.1A
44”Steam
*Denotes240Voltheatingelementsthathavebeendown‐ratedwhen230Voltsisapplied.
**Denotes480Voltheatingelementsthathavebeendown‐ratedwhen460Voltsisapplied.
15
PageCreated:02‐25‐2011
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
ElectricalRequirementsfor66”Units
Volts Phase Freq
Wash
Motor
Amps
Drive
Motor
Amps
Wash
Heater
Amps
FLA MCA MOP
208 1 60 10.0A 1.8A 86.5A 108.5A
111.1A 121.3A
230 1 60 10.0A 1.8A *71.9A 93.1A
95.6A 105.6A
208 3 60 8.6A 1.1A 50.0A 66.5A
68.7A 77.3A
230 3 60 8.4A 1.1A *41.5A 57.4A 59.5A 67.9A
460 3 60 4.2A 0.6A **20.8A 28.8A
29.9A 34.1A
Pre‐Wash
Motor
Amps
10.2A
9.4A
6.8A
6.4A
3.2A
240 1 60
9.4A 10.0A 1.8A 75.0A 96.2A 98.7A 108.7A
240 3 60
6.4A 8.4A 1.1A 43.4A 59.3A 61.4A 69.8A
480 3 60
3.2A 4.2A 0.6A 21.7A 29.7A 30.8A 35.0A
66”with18kWWashHeater
Volts Phase Freq
Wash
Motor
Amps
Drive
Motor
Amps
FLA MCA MOP
208 1 60 10.0A 1.8A 22.0A
24.6A 34.8A
230 1 60 10.0A 1.8A 21.2A
23.7A 33.7A
208 3 60 8.6A 1.1A 16.5A
18.7A 27.3A
230 3 60 8.4A 1.1A 15.9A
18.0A 26.4A
460 3 60 4.2A 0.6A 8.0A
9.1A 13.3A
Pre‐Wash
Motor
Amps
10.2A
9.4A
6.8A
6.4A
3.2A
66”Steam
*Denotes240Voltheatingelementsthathavebeendown‐ratedwhen230Voltsisapplied.
**Denotes480Voltheatingelementsthathavebeendown‐ratedwhen460Voltsisapplied.
16
PageCreated:05‐04‐2010
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
ElectricalRequirementsforBoosterTanks
Volts Phase Freq
Rinse
Heater
Amps
FLA
208 1 60 57.7A 57.7A
230 1 60 47.9A 47.9A
208 3 60 33.3A 33.3A
230 3 60 27.7A 27.7A
460 3 60 13.8A 13.8A
40°FRise‐12KWBooster
Volts Phase Freq
Rinse
Heater
Amps
FLA
208 1 60 82.7A 82.7A
230 1 60 71.9A 71.9A
208 3 60 47.7A 47.7A
230 3 60 41.5A 41.5A
460 3 60 20.7A 20.7A
Note:0nthe208voltmachines,therinseheaterisactuallyratedat17.2KW
70°FRise‐18KWBooster
17
PageCreated:05‐04‐2010
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
INSTALLATIONINSTRUCTIONS
VISUAL INSPECTION: Beforeinstallingtheunit,checkthecontainerandthemachinefordamage.A
damagedcontainermaybeanindicationthereispossibledamagetotheproduct.Ifthereisanytypeofdam‐
agetoboththecontainerandtheunit,DONOTTHROWAWAYTHECONTAINER. The dish‐machine has
beenpreviouslyinspectedatthefactoryandisexpectedtoarrive to you in new, undamaged condition.
However,roughhandlingbycarriersorothersmayresultindamagetotheunitwhileitisintransit.Ifsuch
asituationoccurs,DONOTRETURNTHEUNITTOTHEMANUFACTURER.Instead,contactthecarrierand
askthemtosendarepresentativetothesitetoinspectthedamage.Youshouldrequestthataninspection
reportbecompleted.Youmustcontactthecarrierwithin48hoursofreceivingthemachineinordertore‐
portpossiblefreightdamage.Youarealsoencouragedtocontactthedealerthroughwhichyoupurchased
theunit.
UNPACKING THE MACHINE:Themachineshouldbeunboxedandremovedfromthepalletprior to
installing. Also remove the wooden lift beams and their associatedbracketsaftertheunithasbeenposi‐
tioned.Openthefrontdoorandremoveallofthematerialsfromtheinside.Onceunpacked,verifythereare
nomissingpartstothebestofyourability.Ifyoudiscoverapartismissing,contactthemanufacturerimme‐
diately.
LEVELTHEDISHMACHINE:Thedish‐machineisdesignedtooperatewhilelevel.Thisisimportantto
preventanydamagetothemachineduringoperationandtoensurethebestresultspossible.Theunitcomes
equippedwithadjustablebulletfeet,whichcanbeturnedusingapairofpliers.Verifytheunitislevelfrom
fronttobackandsidetosidepriortomakinganyelectricalorplumbingconnections.
PLUMBINGTHEMACHINE:Allplumbingconnectionsmustbemadetoadheretolocal,state,territorial
andnationalcodes.Theinstallingplumberisresponsibleforensuringtheincomingwaterlinesarelushed
ofdebrispriortoconnectingtothemachine.Notethatchipsandmaterialsfromcuttingprocessescanbe‐
comelodgedinthesolenoidvalvesandpreventthemfromopeningorclosing.Anyvalvesthatarefoundto
befouledordefectivebecauseofforeignmatterleftinthewaterline,andanysubsequentwaterdamage,are
nottheresponsibilityofthemanufacturer.
Waterhardnessshouldbeamaximumof6grainspergallon.Hardwatershouldbetreatedpriortobe
usedbythemachine.Ironinthewaterlinecancausestaining.Ailterdesignedtoremoveironfromthewa‐
tersupplyishighlyrecommendedforsuppliesinexcessof0.1ppm.
Yourdish‐machinecomeswithaWaterPressureRegulatingValve.Theunitutilizesalowpressureof
15PSIfortheincomingwaterline.Donotconfusestaticpressurewithlowpressure.Staticpressureisthe
pressurewhenthereisnolowandthevalvesareclosed;lowpressureiswhenthewaterisrunninginto
themachine.TheWPRVshouldbeadjustedtotheproperlowpressureataminimum.
Thewatersupplylineshallbe1/2”NPTminimumandmustbeabletoprovidewaterattheminimum
temperatureindicatedonthemachinedataplate.
Itisrecommendedashut‐offvalvebeinstalledtoallowisolatingthedish‐machinefromthewatersys‐
temintheeventmaintenanceorotheractivitiesrequireit.Also,itissuggestedthatashockabsorberbein‐
18
PageCreated:05‐04‐2010
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
INSTALLATIONINSTRUCTIONS(CONTINUED)
stalledontheincomingwaterline.Thispreventswaterhammer(hydraulicshock),inducedbythesolenoid
valveasitoperates,fromcausingdamagetotheequipment.
CONNECTINGTHE DRAINLINE: The drainfor the unit isa gravity discharge drain. Allpipingtothe
machinedrainmustbeaminimum1‐1/2”NPTANDSHALLNOTBEREDUCED.Theremustalsobeanair
gapbetweenthemachinedrainlineandtheloorsinkordrain.Ifagreasetrapisrequiredbycode,itshould
havealowcapacityof30gallons.44”unitshaveonedrainconnectionpoint.66”unitshavetwopoints.
STEAMLINECONNECTIONS:Somemachinescoveredinthismanualaredesignedtouselowpressure
steamasasourceofheatforthewashtank.Thosemachinescomewithlinesbywhichanoutsidesourceof
steam(i.e.steambooster)isconnected.Connectallsteamlinesfromtheboostertothemachineinaccord‐
ancewiththeboostermanufacturer’sinstructions.Ensurethatallapplicablecodesandregulationsaread‐
heredto.Seethemachinedataplateforinformationrelatedtosteamlowrequirements.
ELECTRICALPOWERCONNECTIONS:Allelectricalconnectionsaretobemadeinaccordancewithap‐
plicableportionsoflocal,state,territorialandnationalcodes.
DISCONNECTELECTRICALPOWERSUPPLIESANDTAGOUTINACCORDANCEWITHAPPROPRIATE
PROCEDURESANDCODESATTHEDISCONNECTSWITCHTOINDICATEYOUAREWORKINGONTHATCIR-
CUIT.
Thismanualprovidesreferenceinformationregardingelectricalrequirementsandloads,butthatinfor‐
mationmay changewithoutnotice. Alwaysreferto themachinedata platefor voltage requirements, ma‐
chinevoltage,totalamperageloadandserialnumber.Ifyoucannotreadyourdataplatebecauseithasbeen
damaged,youshouldcontactthemanufacturer.
Themainpowerterminalblocks(forthedish‐machineandfortherinseboosterheater,ifapplicable)
are locatedat the topof the machine.You will haveto remove thetopcover toaccessthese connections.
Routeincomingpowerlineswithinconduitthatwillconnectviaittingstothepre‐punchedholesinthe
backoftheunit.Installpowerandgroundwirestolugsasindicatedbytheappropriatedecalsinthecontrol
box.Usecopperconductorsonly.Useofaanti‐oxidationagentis permissible on the power connections.
Tightenallconnections.
Verifytheincomingvoltagematchesthevoltageindicatedonthedecalnexttotheincomingpowerpre‐
punchedhole.
Pleasenote thedish‐machinehasaseparatepower connectionfromtherinseboosterheaterandthe
circuit protection requirementsare different for each.Refertothemachine data plate forinformation on
minimumcircuitprotection.
DISHMACHINEVENTILATION:Thedish‐machineshouldbelocatedwithprovisionsforventingintoan
adequateexhausthoodorventilationsystem.Thisisessentialtopermiteficientremovalofthecondensa‐
tionexhaust.Ensuretheexhaustsystemisacceptableinaccordancewithapplicablecodesandstandards.
19
PageCreated:05‐04‐2010
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
INSTALLATIONINSTRUCTIONS(CONTINUED)
Note:any damage that is caused by steam and/or moisturedue toimproper ventilationis NOT
coveredunderthewarranty.
Thedish‐machinehasthefollowingventilationrequirements:
 LoadEnd:200CFM
 UnloadEnd:200CFM
Theexhaustsystemmustbesizedtohandlethisvolumeforthedish‐machinetooperateinthemanner
itwasdesignedto.
THERMOSTATS:Thethermostatsonyourunithavebeensetatthefactoryforthe wash tank. They
shouldonlybeadjustedbyanauthorizedserviceagent.
CHEMICALFEEDEREQUIPMENT:Yourdish‐machineDOESNOTCOMEWITHANINTEGRALCHEMI‐
CALSUPPLY/FEEDERSYSTEM.Youmustconnecttheunittoathirdpartychemicaldispenserthatmeetsthe
requirementsofNSFStandard29forthemachinetooperatecorrectly.
Youshouldcontactyourchemicalsupplieraboutconnectingadispensertoyourdish‐machine.Chemi‐
caldispensersmustbesetforthetypeandconcentrationofchemicalsbeingusedandthereareseveralfac‐
torsthathavetobetakenintoaccount.
Detergentusageandwaterhardnessaretwofactorsthatcontributegreatlytohoweficientlyyourdish
machinewilloperate.Usingtheproperamountofdetergentcanbecome,intime,asourceofsubstantialsav‐
ings.Aqualiiedwatertreatmentspecialistcanexplainindetailtoyouwhatisneededtogainthemaximum
eficiencyfromyourdetergent.
Thedish‐machineis able tooperatein eitherhotwater sanitizingmodeor chemicalsanitizing mode.
Yourunitshouldbeclearlymarkedabovethedataplateastothemodeitisin.Ifyoucannotdeterminethis,
contactthemanufacturerimmediatelyforassistance.
Itisimportanttorememberthatifyoudecidetooperatetheunitinchemicalsanitizingmode,youmust
ensureanappropriatechlorine‐basedsanitizerisusedintheinalrinseline.
20
PageCreated:05‐04‐2010
Revised:N/A
TechnicalManual(07610‐003‐78‐18)
INSTALLATIONINSTRUCTIONS(CONTINUED)
DETERGENT INJECTION POINT.
ANOTHER BULKHEAD PLUG
IS PROVIDED ON THE LEFT SIDE
OF THE UNIT
1-1/2" NPTF DRAIN CONNECTION
ADJUSTABLE BULLET FEET
BULKHEAD OPENING FOR
CONDUCTIVITY PROBE
CHEMICAL TUBE
INSERTION POINT
875"
INLET WATER FITTING
1/2" NPTF
MAIN ELECTRICAL
CONNECTION OPENING
1.375"
BOOSTER HEATER
ELECTRICAL CONNECTION
OPENING
1.375"
SHOWN FROM REAR OF LEFT TO RIGHT UNIT.
RIGHT TO LEFT UNIT IS MIRRORED
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87

Jackson 44S User manual

Jackson
Brand
Jackson
Model
44S
Category
Dishwashers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents